- Post is under moderationCAR: #BMW-E46 / #BMW-M3 / #BMW-M3-E46 / #BMW-E46 / #BMW-M3 / #BMW-M3-E46 / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46 / #BMW-M3-Coupe / #BMW-M3-Coupe-E46
MILEAGE THIS MONTH: 156
TOTAL MILEAGE: 87,276
MPG THIS MONTH: 26.9
TOTAL COST: £167 (tyres & locking nuts)
Clubsport? Lightweight? Race car? Well, not quite; but sitting inside, the M3 does have the look of a car midprep for an attack on a Nürburgring laptime. A couple of delays mean the M3’s interior is still missing a fair proportion of its trim, but the guys at Perfect Coating (www.facebook.com/ perfectcoating) will have that sorted by the next update, so I’m looking forward to photographing the interior in its shiny new glory in time for next month. Talking of next month, with good weather on the cards and some events in the calendar I’m planning to take the M3 to Wales with some mates, and if things work out just-so, a sojourn to the Nürburgring too. Throw in another visit to Bruntingthorpe for VMAX and I’ll have a chance to put some good quality bonding miles on the M3. Truth is, I’ve not used it as much as I’d like of late which may be good for the mileage (a relatively low 87k considering the 2002 year of registration) but this is not a car to be afraid of using – you only need to look at the amount of M3s deep into six figure mileages to know that if well looked after, there is nothing to fear. With the service indicator telling me I have 800 miles left before the next service, she’ll be well looked after very soon, most likely by Highams Park Motor Company in East London.
It’s the perfect time for some routine maintenance, meaning I can look forward to summer fun with her! That’s not say I’ve not had fun in the dark months, and now I’ve had a chance to put some proper miles on the M3 with the 18-inch wheels I’ve really grown to love them. Unsurprisingly, after last month’s sideways fun the rear tyres were looking rather sorry for themselves. Lucky for me, my local tyre shop happened to have a pair of very lightly used correctly sized Pirelli P Zeros in stock; an absolute bargain for £150, and I had some new locking wheel nuts fitted at the same time. The old lockers were looking pretty sorry for themselves, and I had visions of being stranded with a flat, unable to change wheels due to a rounded off key. It’s a small thing, but it gives peace of mind. As I reported last month, initial impressions on the smaller wheels were a marginal trade off in ultimate grip in return for better ride quality and even more benign, playful handling characteristics when pushing on.
With the new Pirellis, a good run on some of my favourite local B roads cemented that impression. I’ve never been one for chasing ultimate grip anyway – I’m not setting lap times – so I’d rather have a car which has grip levels well matched to the power output, with really enjoyable handling which can be exploited at sensible speeds. On the 18-inch wheels, the M3 delivers this by the bucket load. I’ve grown to love the look on the dark grey smaller wheels too; the polished 19-inch wheels always looking a bit bling for my taste.
Despite sharing space with cars worth 50+ times what I paid for the M3, it still managed to turn heads and secure a prime spot at a local breakfast club meet. If you’re an Essex dweller, I’d heartily recommend a trip down to The Hare near Roxwell the first Saturday of most summer months (check its calendar to be sure). Get there early enough and there’s even free coffee. But more importantly an excellent mix of old, new, and sometimes hugely rare and valuable cars to have a look at… and a 15 year old M3 with half the interior missing. It was my morning jaunt to the last meet that gave me the chance to enjoy my favourite local roads, and driving back I was feeling pretty pleased with life. I think it’s fair to say my love affair with the M3 is going pretty strong…Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationHARRY NEWMAN #BMW-E46 / #BMW-330Ci-Sport / #BMW-330Ci-Sport-E46 / #BMW-330Ci-E46 / #BMW-330Ci / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46 / #BMW
Just over 18 months ago, Harry made the move from 318Ci to 330Ci, but it’s not just any 330Ci, this is an Individual example and needless to say Harry is over the moon with it. It’s finished in stunning Mora metallic which, according to Harry’s research, makes it one of possibly just 28 examples produced in this colour, making it an exceedingly rare machine. Nice as it was, a little tasteful modding was on the cards and, not being a fan of aftermarket parts, Harry has gone down the OEM+ route with his E46. A set of Eibach lowering springs have been employed on the suspension front, along with a solid aluminium front strut brace, and the 18” CSL-style wheels that he’s fitted really suit the car. As far as styling is concerned, the kidneys and front lower grilles are now gloss black along with the rear diffuser, the windows have been tinted as have the LED rear lights that Harry’s fitted, along with the front indicators. Under the bonnet there’s a GruppeM carbon intake, which will soon be joined by a set of bigger injectors and a custom remap plus an Eisenmann exhaust system.Stream item published successfully. Item will now be visible on your stream.
- Post is under moderation/ BMW / THOMAS’ E46 M3 / #BMW-E46 / #BMW-M3 / #BMW-M3-E46 / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46 / #BMW-M3-Coupe / #BMW-M3-Coupe-E46 / #BMW-M3 /
This month has seen various areas of the ’46 progress well, with the rear subframe undergoing a complete overhaul, new brake lines being fitted, the cylinder head rebuild starting, and the crankshaft receiving a full re-grind and balance. Starting with the subframe, I was initially thinking of powder coating the whole lot, but the more I thought about it the more I wanted to find something with a little bit more longevity to it. Although powder coat is reasonable hardy, I find it hard to believe it would really stand the test of time without flaking and/or peeling off. So instead I purchased some two-part epoxy mastic from Bilt Hamber – essentially it’s super glue that’s coloured black. With Zinc-phosphate embedded within the resin, once set it provides a supertough, corrosion-resistant surface that should help preserve and protect the subframe.
The subframe was taken back to bare metal and a liberal amount of epoxy applied. Whilst the underside of the car was all apart, I discovered the hard lines for the brakes were close to corroding through, so replacements here were also produced. Once again, I wanted to make sure that whatever went back in the car would last, so Cunifer pipework was used. A copper-nickel alloy, Cunifer is significantly more resilient than steel or copper alone with the trade-off being a relative lack of flexibility – although this didn’t prove to be a problem in the slightest.
By comparison, rebuilding the cylinder head has so far been a breeze. Valves, springs and retainers were the first items to be re-installed. With all the valves numbered on removal it was a case of fitting them in the correct port and giving them a quick lap. Lapping is done by applying a small amount of paste to the seat of the valve, then rubbing it back and forth on the valve seat for a few minutes. This process grinds a small layer of material off the mating faces, helping them to create a better seal with each other. Once the lapping process has been completed, it’s important to check both faces seat around the full perimeter. This was done using engineer’s blue, which was applied to the valve, then the valve was seated (with a fair bit of force) into the head. Once seated, remove the valve and check for an even coverage of blue on the cylinder head valve seat. All valves passed so it was onto the next step. This involved fitting new rockers and rocker shafts, with the former of the DLC (Diamond-like coated) variety. With the engine receiving a set of race-y cams (full specification to be revealed later), it seemed sensible to upgrade to the more slippery, harder-wearing DLC rockers.
And so onto the crank, where a fair amount of head scratching and research has been involved this month. First and foremost, I need to thank Daren of Crosthwaite & Gardiner for doing a superb job of regrinding my crank. It turns out the crank was in a bit more of a state than it first appeared, yet after a few tense hours of careful measuring and grinding, it’s ready to spin in anger. Regrinding the crank was incredibly eyeopening for me. There’s a lot of discussion online about how marginal the big ends are on S54s, with numerous people (including myself) removing shells after ~100k miles and finding they’re in a terrible state. I knew I was in for a regrind on the big ends, but what became apparent was that the mains weren’t too great either.
Despite the main journals looking fine, and measuring up OK at first glance, the crank was bowing considerably (0.125mm eccentricity was measured between the mains). After a bit of straightening and a light polish, the mains were running true again, although it became evident they weren’t so healthy, with noticeable scoring to the journal surfaces showing. How deep the damage went was very surprising – it was only when 0.2mm had been removed from the journals (of the 0.25 total) that all the scoring was removed. It was a similar story too with the big ends, with all of them requiring considerable material removal before cleaning up. On the big ends it was always the top and bottom side of the journal that showed the most damage, evidently from the combustion stroke and rod/piston inertia during the exhaust stroke.
Considering the state of the crank, I decided it was worth doing a bit of research into the shell/big end issues on the S54 to see if a solution could be found. Reading back through information online, it was news to me that these engines originally shipped on a 5W30 oil, before numerous big end failures forced BMW to switch to a 10W60 Castrol (as used now). Unfortunately this appeared to make matters worse, and it was soon after that BMW increased the clearances in the big end shells (forcing a recall of many M3s). Looking at how tight the shell/crank tolerance is for the S54, to me there’s no doubt these engines were designed around the 5W30, with the change to 10W60 a knee-jerk reaction to try and solve the big end issues.
It was from here that I started speaking to Driven, manufacturers of Joe Gibbs Racing Oils. Its range of oils are developed from research undertaken when trying to push the limits of highly-strung Nascar engines. These struggle to cope with incredibly high stresses on the camtrain, leading to premature wear and power loss. The Driven oils, therefore, focus heavily on reducing engine wear, as well as friction reduction for a competitive advantage. Upon discussing the S54 issues with the development team in the US, the first thing that became abundantly clear is that oil changes every ~15,000 miles in a performance engine is simply not OK. Like all products, oil has a lifespan, and when it’s being pushed hard in what’s essentially a road-going race engine, expecting it to last so long is very wishful thinking. To create oils that operate over a wide viscosity range, modifiers have to be added to the formula, and over time these break down, reducing the oils’ performance. To try and make an oil last 15,000 miles, its chemistry must also be heavily biased with detergents, leaving less room for anti-wear components.
On top of this, levels of #ZDDP ( #Zinc-dialkyldithiophosphate ) in oil have been reduced considerably. This is an important anti-wear compound, but due to its slightly negative effects on catalytic converter performance, governments are restricting its use in commercial/OEM engine oils. Driven has worked incredibly hard to reduce wear, with all its oils having considerably higher levels of ZDDP. Driven even has extensive dyno results to back up its claims. I’ll be looking to run the DT40 5W40 from the Driven range; with regular oil changes (every 6000 miles or so) this should keep the motor running sweetly and ensure the crank doesn’t lose any more precious material from its journals. Regular oil changes can’t be recommended highly enough for M car owners…Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationPOWER UP Hardcore, supercharged E46 330Ci
What was once a stock 330Ci has now evolved into a supercharged, track-focussed monster. Words: Elizabeth de Latour Photos: Viktor Benyi.
’CHARGED BMW E46 330Ci Track-focussed full-on build…
Supercharging a “lesser” model of BMW is something that a lot of people don’t really understand. “Why didn’t you just buy an M3/ M5/M6 in the first place?” they will ask and, in absolute terms, you can see their point. Why spend arguably the same amount of money, or perhaps even more, buying and subsequently supercharging something that isn’t an M car and ending up with around the same sort of power level, when you could have just bought a fully-fledged, finely-honed M machine in the first place? It’s a valid, logical point, but logic has little place in the world of modifying. The thing is that very few people buy a car knowing exactly where they’re going with it, how it’s going to end up and with the specific plan of supercharging it. Sure, some people do, but take a look through this issue, the last issue, pretty much any issue of the mag and you’ll see feature car after feature car owner saying that they really had no intention of going as far as they did with their cars. The other thing is that, generally speaking, something like a supercharger is usually one of the last mods anyone does and that’s because it makes a lot more sense – and here logic can be applied to modding – to sort out the chassis, the brakes, make sure everything else is up to scratch before you start ramping up the power. It’s the right way to do it, really.
Which brings us neatly to Richard Kiraly and his supercharged E46 330Ci. As you can probably tell from the pictures, this is one exceptionally well-sorted 3 Series and, as you won’t be at all surprised to learn, when Richard bought the car there was no plan for anything beyond the most basic of mods, let alone creating a car as full-on as this has ended up becoming. Richard has been a BMW owner for 12 years, though that time period has been divided up between just three cars: his first BMW, an E34 525tds, which was followed by an E39 525d, and now the E46. Thing is, while he may say there was no plan of attack here, both of his previous Bavarian steeds, and a couple of cars before that, have all received some level of mild modding, so we reckon he wouldn’t have been able to leave the E46 alone anyway.
Hailing from Hungary, Richard’s hunt for the right example of what was the most affordable way of fulfilling his childhood dream of owning a frameless window coupé took him all the way to Leipzig in Germany, after six months of searching, and what was then a plain old 330Ci Sport. With car in hand, the mods began and stage one was styling. The E46 Coupé is a fi ne-looking thing, we’re big fans, but go big or go home, right? Go big it was, with Richard giving his 330Ci the M3 look courtesy of the M car’s wings and bumpers before cranking things up to 11 and taking the styling to another level. The front bumper has been seriously beefed-up with the addition of that carbon lip and those full-on corner splitters and even the intakes that funnel cooling air to the brakes are made from carbon. The bonnet? That’s carbon too, a vented GTR item that’s been painted body colour with just the slats of the vents left bare, teasing its carbon construction. M3 mirrors have been added while at the rear there’s a unique diffuser, a set of LED lights and a fibreglass CSL-style boot lid to finish things off nicely. It’s a greatlooking car, all the styling enhancements blending together perfectly and with the M3 body parts on board, the more aggressive aero elements don’t overwhelm the look of the whole car.
The wheels are Japan Racing JR3s, which suit the look and direction of the car perfectly, and while their familiar sixspoke design doesn’t get your attention, the colour certainly does. It’s a bold, bright blue that doesn’t tie-in with anything, anywhere on the car but wow, does it look good. Somehow it just works so well against that sexy, solid grey paintwork and your eyes are immediately drawn to the wheels. They’re the first thing you notice on the car and you realise that, actually, opting for that punch of colour was definitely the right thing to do as it really makes them stand out. You can probably tell that this car hasn’t been built for show, it’s all about go, and peering between the spokes of the JR3s confirms that beyond any reasonable doubt as that’s when you notice the massive brakes. The calipers come from a 135i, says Richard, with six-pots up front clamping M3 CSL discs, and two-pots at the rear while the suspension has also been suitably uprated and these mods came about when he decided to start making track outings a regular occurrence. BC Racing coilovers have been fitted here, and they deliver a solid drop, along with uprated anti-roll bars, Powerflex bushes, Eibach adjustable rear control arms and front and rear strut braces, completing a comprehensive programme of upgrades. The interior changes, too, have come about from the car’s regular appearance at track days and amateur tournaments; up front, a pair of bucket seats have been fitted, along with a set of Schroth three-point harnesses, while the rear seats have been removed altogether, as has the air-con. White-faced dials have been added to give the gauges a sportier look and Richard has also fitted a digital display in place of one of the central air vents to keep an eye on various under-bonnet temperatures.
So, to the engine. The M54B30 is a great motor, plenty of torque, a lovely top end, plus it sounds lush but by modern standards it’s not going to set anyone’s world alight and with him being so committed to track driving, you can see why Richard wanted a little more performance. NA mods are fi ne and could liberate a bit more horsepower but if you want serious gains then you have to bring out the big guns and go straight for forced induction. What Richard’s got strapped to the side of his engine is an ESS TS1 supercharger kit, which uses a twinscrew, positive displacement blower, and that means it delivers a huge hit of low-end torque the moment you hit the accelerator, perfect for punching out of turns on track. It’s an impressive piece of kit and puts out some meaty numbers, 320hp and a very healthy 302lb ft of torque. Here it’s been further bolstered by the addition an #AFE high-flow intake, a set of Schmiedmann high-flow cats and a ProEx exhaust system with racing silencer while an S54 oil cooler helps keep temperatures down on track. The transmission hasn’t been forgotten about, either, and Richard’s fitted a lightweight flywheel and Sachs race clutch plus an LSD to help him put all that power down.
We really like Richard’s E46. It’s been built with purpose after being bought with no specific direction in mind. It’s a focussed and finely-honed machine, but one that’s not so extreme that it can’t be used on the road. It looks good and it’s got the power to match the extreme aero additions; it really is an exceptional performance package. Richard has spent eight years getting the car to where it is today, but he’s not done yet and the next round of mods is imminent. “I want to cover the interior in Alcantara,” he says, “and I’ve currently got a CSL front bumper with twin brake air inlets under construction and I’ve also got an ESS TS2+ supercharger kit ready to go,” he adds, which is really going to take this E46 to the next level.
TECHNICAL DATA FILE #BMW #Supercharged / #BMW-E46 / #BMW-330Ci / #Japan-Racing / #ESS-TS1 / #ESS-Tuning / #BMW-330Ci-E46 / #BMW-330Ci-Supercharged / #BMW-330Ci-Supercharged-E46 / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46
ENGINE AND TRANSMISSION 3.0-litre straight-six #M54B30 / #M54 / #BMW-M54 , #ESS-TS1-supercharger-kit , #AFE air filter, #Schmiedmann sport cats, #ProEx exhaust system with racing silencers and black heat-resistant quad tips, S54 oil cooling system. Five-speed manual gearbox, lightweight flywheel, #Sachs racing clutch, short-shift kit, #LSD
CHASSIS 8.5x18” ET15 (front) and 9.5x18” ET15 (rear) #Japan-Racing-JR3 wheels with 225/40 (front) and 255/35 (rear) tyres, #BC-Racing coilovers, uprated anti-roll bars, #Powerflex bushes, #Eibach adjustable rear control arms, front and rear strut braces, #Brembo six-piston calipers with M3 CSL discs (front), #Brembo two-piston calipers (rear), braided brake lines, competition brake fluid
EXTERIOR E46 M3 wings, front and rear bumpers, carbon front splitter, front bumper race air intake, GTR carbon bonnet, E46 M3 door mirrors, custom rear diffuser, E46 M3 CSL-style boot lid, LED rear lights
INTERIOR White gauges, digital data display in central air vent, bucket seats, three-point Schroth harness, rear seats removed, air-con removed, spare wheel well removed, fire extinguisher
“What Richard’s got strapped to the side of his engine is an #ESS-TS1 supercharger kit, which uses a twin-screw, positive displacement blower”
BC Racing coilovers with adjustable top mounts.
135i brakes have been fitted all-round.
“The wheels are Japan Racing JR3s… and while their familiar six-spoke design doesn’t get your attention, the colour certainly does”
Bucket seats, harnesses and rear seat delete let you know this E46 means business.Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationLongtermers #BMW-E46 / #BMW-M3 / #BMW-M3-E46 / #BMW / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46 / #BMW-M3-Coupe / #BMW-M3-Coupe-E46 / #BMW-M3 / #2002
Plenty of action for the M3, Ben gets his German race licence, Elizabeth almost says goodbye to the 1 Series while the repaired E90 318i has more dramas
After a couple of quiet winter months the M3 must be wondering what’s hit it! New wheels, interior in pieces… it’s even been on track alongside a couple of fun jaunts on local roads. Let’s start with the interior refresh. I’d been talking to the guys at Newbury based www.perfectcoating.co.uk for a few weeks about some options to revive the scuffed, scratched and scabby grey plastic interior trim in the M3. The interior of my car was in great shape overall when I purchased it – nice shiny seats with only mild bolster buffing, whilst the dash and remainder of the cabin trim was in excellent shape, perhaps even better than you’d expect of an 80k mile, 15-year-old M3. Letting it down though, were always the plastic inserts with their metallic grey finish. Given these adorn the door handles and electric window switch surrounds amongst others, they were in prime position to deteriorate from 15 years of contact with rings, nails and the natural oils from human skin.
So a jaunt over to Newbury was arranged, where the guys at www. perfectcoating. co. uk had the relevant parts out of the car in short order. The individual pieces looked even worse sitting on a bench under bright lights, the door handles predictably being the worst offenders. The parts are sanded down to remove the existing paint and prepared for the black basecoat.
Once this is applied, the clever part of the process happens, as the film is applied through hydro dipping (or water transfer printing as it’s known) to create a finish which looks almost identical to a carbon weave, with some golden colour showing through (we opted for this to better match my M3’s Phoenix yellow – many other finishes and colours are available).
Once this has cured (a very quick process), the parts are sent to the bodyshop for a high quality lacquer to give a deep, lustrous and hardwearing finish. Having seen some completed parts earmarked for a Mustang I was blown away by the quality and can’t wait for the finished items to be refitted – pictures and in-depth report on the process next month. The fact that the process is just as suitable for external parts is highly compelling: carbon spoiler and mirrors anyone? My return journey from Newbury made for an easy drop in to Aldershot to pick up the set of original 18- inch wheels I sourced through the popular M3cutters forum. I’d been interested to try these and experience for myself if the ride and handling were tangibly different on the smaller rims and accompanying taller sidewall tyres. There is a marginal reduction in unsprung weight over the 19-inch polished alloys, shedding 1.4kg per front and 1.1kg from each rear wheel; of course this is mitigated by the slightly heavier rubber due to the taller sidewalls. In reality, it’s the latter which seems to make the biggest difference to the driving dynamics in the handful of miles I’ve been able to try them so far.
Tyre footprint remains the same, with 225/45/18 up front and 255/40/18 at the rear as opposed to 225/40/19 and 255/35/19, but the taller sidewall has reduced initial bump harshness, whilst there is a trade off to steering sharpness when turning in. Perhaps due to less tyre deformation, it feels like the 19s have slightly more ultimate lateral grip, but we are talking fi ne margins here which would take an accelerometer to confirm. On the road, the 18-inch setup does feel like it works better, providing the M3 with an added degree of suppleness to deal with our imperfect roads. At the same time, the chassis feels a little bit less edgy on the limit, proving extremely friendly with the DSC turned off ; a feeling I was able to confirm on track recently where some pretty extreme corner entry styles had the M3 virtually on the lockstops in third, but feeling utterly benign and predictable in extremis, as well as sensational fun. Of course, much the same can be said of the wonderfully balanced E46 M3 chassis no matter which wheels you’re running, but there was a tangible and enjoyable difference to note. That the 255/40/18 rubber is significantly less expensive than 255/35/19 is a pleasing side benefit….
This has freed up the 19s for a refurb too. They are thankfully free of kerb rash, but the lacquer is looking a bit second hand in places. If you have any recommendations of a place to have these cost effectively refreshed in Essex or London please feel free to message me.
BMW E46 M3
MILEAGE THIS MONTH: 622
TOTAL MILEAGE: 87,120
MPG THIS MONTH: 28.8
TOTAL COST: £350 (wheels)Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationGorgeous E46 M3 / Slick E46 slammed, styled and tuned
THE PEOPLE’S CHAMPION / Words: Elizabeth de Latour / Photos: Sunny Ryait
With a perfect blend of styling and tuning mods, this E46 M3 really is the modified package that everyone can enjoy the people’s.
Oh yes, this is what we’re talking about. As much as we love all the air ride, the big wings, the engine swaps, the turbos, superchargers and wild wide-body kits, sometimes you just want something a bit more down to earth, a bit more achievable, affordable, a people’s champion that we can all get behind and enjoy, and Richard Ansari’s E46 M3 is that car. It looks great, that’s going to be your first reaction, because it really does, but as with many seemingly simple builds, there’s a lot more going on here than you might first notice and Richard has really put a lot of love and hard work into his M3 over the past five years.
The E46 M3 dream must have seemed almost unattainable back when Richard passed his test and got behind the wheel of a mighty 1989 Mazda 626. A BMW was going to happen though, there was no doubt about it, thanks to his dad’s decision to run a string of Bavaria’s finest when Richard was growing up, but what really sowed the seed deep down into his brain was the blue E30 325i his dad once owned. “I couldn’t get into BMs right away as soon as I passed my driving test as insurance was one roadblock as well as being a student in my younger years,” he laughs and it wasn’t until he turned 23 that he could finally make that dream a reality. “By pure chance my mate had decided to sell his E30 325i Cabriolet and gave me first dibs on it before advertising it. I knew the car and while it did have some very questionable mods, underneath it all was decent, having had a full respray, no rust, was structurally sound and had cream interior to complement the Zinnober red exterior. It was almost like reliving my childhood with those memories sat in my dad’s E30, but this time I was behind the wheel,” he grins.
Over the next three years the E30 underwent a transformation that saw it ending up with a 2.7 conversion and receiving a feature in these very pages back in March 2007. The E30 was then followed by an E46 330Ci and that path could only lead in one, inevitable direction... “The E46 M3 was a dream car for me,” says Richard, “and when my mate bought one in late 2010 and let me drive it, I made a plan there and then to own one in 2011. I had originally wanted one in Techno violet but, being a very rare colour, it was mission near-impossible to find one, so I started to look at a few other colours as a second option,” he says. That led him to Pistonheads, where he stumbled across this Steel grey Coupé, with a manual gearbox and just 50,000 miles on the clock. Richard grabbed his friend Dips, from Custom Cars, headed over to take a look at the car and ended up buying it. “I wanted to keep this one fairly standard except for a couple of subtle mods, keeping away from doing any more big modifications,” he laughs, “unfortunately, though, once I fitted a set of CCFL angel eyes and black kidney grilles, it was a bit like opening Pandora’s box,” and so we begin…
With the angel eyes and black grilles being joined by a pair of black wing vents, Richard decided to carry on with the styling mods, adding smoked Depo indicators and repeaters and tinting the outer rears to match with Lamin-X film, then sourcing and fitting a set of facelift smoked inner lights. At the rear there sits an AC Schnitzer-style carbon fibre diffuser, which fills out the bumper nicely, along with a genuine CSL bootlid, while up front, a Strassentech-style lip adds an air of menace to proceedings and is joined by a set of Hamann foglight covers, with smoked fogs. Richard says that his plan was to enhance the car’s looks without going crazy, and we have to say he’s most definitely achieved his goal. The styling additions he’s chosen give the M3 a more pumped-up appearance, accentuating its aggressive styling, but without going too far or overwhelming the looks. And, while his first choice of colour may have been Techno violet, we’ve got to say that Steel grey looks really good on the E46 M3.
The suspension has been through a few changes during Richard’s time with the car. He started off small, with just some Apex lowering springs but it wasn’t long before he found himself wanting more adjustment and decided to take the plunge with some coilovers. His first set were from D2 but the car now runs BC Racing coilovers, which offer all the adjustability he could ever want and have allowed him to achieve the perfect ride height. “With the suspension sorted I was looking at big brake kits as the next big upgrade,” he tells us. “For the M3 there are a lot of options and routes you can go down and then, one day, an ad came up for a complete set of AP Racing brakes from Imran at Evolve Automotive. After a quick think, and after checking the piggybank, we did the deal and I picked them up. It did occur to me, not long after that, what would I do if my wheels didn’t have enough clearance, without having to resort to using big spacers, but figured I’d worry about it later. One way or another there was not going be any compromise, so I dropped the calipers over to Dips at Custom Cars to work his magic, turning them from red to orange.
I really like the way they look behind the wheels but beyond that the stopping power is so consistent compared with the OEM setup. I mounted the front wheels to check for clearance and luckily to my surprise only a 5mm spacer was needed,” he says.
As far as the wheels are concerned, Richard didn’t start off small and work his way up to something impressive, he went big right away, kicking things off with a set of AC Schnitzer Type 3 Racing splits, which are a great-looking classic wheel design. But that wasn’t enough for him, he wanted more… “I wanted something a bit special,” he says, “it had to be a three-piece wheel and my ideal choice was a set of Hartge Design C splits, but not only are they rare they also command a huge premium. I wanted something that you don’t see everyday and it had to have friendly offsets, with the aim of building a set of wheels wide enough, without needing any major work to fit straight on and not needing any camber.
After missing out on a set of Oz Futuras, I found some Oz Mitos on German eBay just before whisking my partner off to Marrakech for her birthday; I had an idea of what they looked like on a normal E46 but couldn’t find a set fitted to an M3 anywhere, so I knew this was my opportunity to run something fairly unique. Midway through the holiday, while she was getting ready in our hotel room, I placed a bid just before the auction finished and won,” he grins. Best. Holiday. Ever.
“They were 18s with the right offsets and being the Type 1 version, which are reverse mounted, are pretty rare in a BMW fitment. As soon as they arrived I went down to Dips for a test fit and we worked out what lip sizes to run front and rear. Originally they came as 8.5x18s and 9.5x18s and I really wanted to run an 11” wide wheel at the back, so Dips started the strip down of the wheels for a full refurb. He ordered 3.75” lips for the rear and moved the 2” lips to the front making the new setup 9x18” and 11.25x18”.
We knew an arch roll was needed, so Dips got that sorted and, with fresh Continental tyres fitted, we mounted the wheels. Seeing them built up and fitted on the car I knew I had made the right choice,” he grins. “They just completely changed the way the car looks, but not only that, the fitment is perfect too, with no rubbing or any negative camber required to aid with clearance.”
With the car looking on point as far as styling was concerned, Richard popped his bonnet and took a good, long, hard look at the engine bay. “At first I had no real plans on doing any engine mods,” he admits, “that is until a group buy came up for some Geoff Steel Racing air boxes on the M3 Cutters forum. After reading the feedback on it and with a bit of encouragement from forum members I went ahead and placed a pre-order.”
Usefully, as part of the group buy, Evolve joined in with a special offer on Alpha N remaps to go with the air boxes so, with his sexy new carbon air box fitted, Richard headed up to the company’s Luton HQ to get the car remapped. “These cars make anywhere between 320-330hp on average,” he explains, more than a few ponies shy of BMW’s 343hp claim, “and originally mine made 321hp. After fitting the airbox and mapping it, we saw 349hp, which was a very nice gain and was noticeable on the road. As well as that is the induction noise you get as soon as you floor it. It makes such an awesome roar you never get tired of it and want to hear it more and more,” he says with a grin. “To complement the airbox for sound and for a little extra power, I fitted a set of 100 cell cats paired with an Eisenmann Race rear box, which has given a better throttle response through the rev range. To finish off I got the holy grail of exhaust manifolds, with a set of Supersprints, which very rarely come up for sale. They were brand new but never fitted and I soon snapped them up to complete the setup.”
While he may have been sorted for power, that carbon air box was showing up the rest of his engine bay, so action needed to be taken. Obviously carbon was the way forward, and Richard began to develop a little bit of an obsession with the mesmerising weave. First came an intake cover that fits over the existing item but also partially covers the front of the air box, and once that had been fitted, obsession became unstoppable addiction. Desperate to feed his habit, Richard read up on and briefly considered having a go at carbon skinning, before he found Prapan, who runs NVD Motorsport, and saw his carbon-skinning talent. Quick as a flash, Richard had removed his emissions pump, xenon ballasts and ECU cover and handed them over for skinning in 2x2 weave to match the air box and also asked for a pollen filter cover. The six week wait to get the parts back was absolutely worth it but when it came to getting the rocker cover skinned, the cost of postage and import duty was proving prohibitive.
Richard found himself a slightly more local carbon skinner by the name of Jaydee Customs, over in Poland, who duly skinned the aforementioned rocker cover, leaving Richard with virtually nothing left to cover in carbon. The finishing touch here in the engine bay is a rather sexy and substantial Rogue Engineering strut brace. And now we come to the interior, because of course Richard couldn’t leave that alone either, and we’re glad he didn’t.
Originally, his M3 had been fitted with the black leather interior, nice but a bit plain and, for Richard, lacking contrast against the Steel grey exterior. “I didn’t want to settle for red,” he says, “so I searched for a year until a rare Cinnamon interior came up on E46 Fanatics. It wasn’t a sale but a straight swap for black leather, offered by a chap called Mark who was working for Nitron Racing at the time. So after a brief chat on the phone we arranged for me to come down to him one day and we both swapped out our interiors at the premises. For me it made such a huge difference, not just the fact it was a nicer place to sit in now, but it goes so well with the car.” We have to agree as we’re big fans of coloured interiors, they make such a nice change from the usual dour shades, and Cinnamon is seriously lush.
It’s further complemented by matt dark myrtle wood trim, an unusual choice for an M3 and an extremely rare trim option, but it’s absolutely gorgeous and looks so good here. The steering wheel has been re-trimmed by Royal Steering wheels, with extra padding, cinnamon stitching and a cinnamon centre stripe while the gearknob has been replaced with an illuminated F10 M5 item with matching gaiter, mounted on an E60 short shift for crisper gear changes. Finally, Richard’s most recent interior mod, is the Awron gauge mounted in the driver’s-side centre air vent. “It was a bit of an impulse buy,” admits Richard, “I saw a demo of it on YouTube and when I saw they had made them for the E46 I got one ordered. It goes nicely with the dash and it’s a nice bit of kit, displaying various parameters from intake temperatures to O2 sensor voltages along with a G force meter and loads more functions.”
It’s taken Richard four years to get his M3 to where it is now, and he couldn’t be happier with the result of all that work. “I think where it is now I have found that place where I wouldn’t change much else,” he smiles. “A full respray is on the cards next, in the original colour, and I want to get the map tweaked with the addition of the exhaust mods. But my long term plan if I can is to keep the car and hopefully one day give it to my son,” which would be an amazing gift, and something very special for that young man to hold onto. So, does that mean Richard’s hanging up his modding hat for now? No… “I have an E30 325i Cab which I bought over four years ago as a project car so, with the help of Dips, there are some big plans for it. Watch this space!” he says with a smile and you can be sure we will be.
“… I think where the car is now I have found that place where I wouldn’t change much else”
/ #BMW-M3-E46 / #BMW-M3-Tuned-E46 / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-M3 / #BMW-3-Series-M3-E46 / #BMW-M3-tuned-E46 / #BMW-M3-tuned / #Evolve / #BMW / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46
TECHNICAL DATA FILE #BMW-E46 / #BMW-M3 / #OZ
ENGINE AND TRANSMISSION 3.2-litre straight-six #S54B32 / #S54 / #BMW-S54 , #Geoff-Steel-Racing carbon fibre air box, #Evolve-Alpha-N remap, #Supersprint-V2 exhaust manifolds, 100 cell race cats, #Eisenmann Race rear exhaust section with 83mm tail pipes, carbon fibre engine cover, emissions pump cover, ECU cover, xenon ballasts and pollen filter cover, Matt Haley billet aluminium oil filter cover, #Rogue-Engineering one piece strut brace. Six-speed manual gearbox
CHASSIS 9x18” (front) and 11.25x18” (rear) three-piece #Oz-Mito wheels with 225/40 (front) and 255/35 (rear) Continental ContiSportContact 3 tyres, #CA-Automotive stud conversion kit with Motorsport Hardware wheel nuts, BC Racing BR series coilovers, Revshift 80a subframe bushes, #AP-Racing-BBK with six-pot calipers and 356mm discs (front) and four-pot calipers and 328mm discs (rear), custom orange calipers
EXTERIOR Original Steel grey paintwork, Strassentech-style front lip with carbon fibre insert, Hamann fog light covers, smoked fog lights, black kidney grilles, black wing vent grilles, 4000K CCFL angel eyes, Depo smoked indicators and side repeaters, carbon fibre black and white bonnet and boot roundels, AC Schnitzer carbon fibre rear diffuser, OEM CSL boot lid, Lamin-X smoked rear lights, Eagle Eyes smoked inner boot lights
INTERIOR Full cinnamon interior swap, matt dark myrtle wood trim, re-trimmed padded steering wheel with cinnamon stitching and cinnamon centre stripe, F10 M5 gear knob and gaiter, E60 V8 short shift kit, Awron digital vent gauge
THANKS Dips at Custom Cars for his input and direction over the years, Teddy at SSDD Motorsport, Prapan at NVD Motorsport, Jaydee Customs, John at carbolts.co.uk, Evolve Automotive, Alex at Elite Car Care, Jack at Royal Steering Wheels, all my friends, family and my understanding wife for supporting my passion for cars over the yearsStream item published successfully. Item will now be visible on your stream.
- Post is under moderationThomas Koflach’s #BMW-E46 / #BMW-M3 /
This project came about through a fair amount of luck on my part. An E46 M3 had been on the radar for a few months – the lure of the straightsix was well and truly calling and having been out in my brother Ben’s #S54 Touring on numerous track days I knew just how good the engines were. The difficult part was, I wasn’t quite sure exactly what I wanted or what would fit the available budget.
It was therefore fortuitous when Ben mentioned that a friend’s E46 had just thrown a rod in spectacular style, punching no less than three enormous holes in the block. The rolling shell was semi-broken for parts before being moved on as a whole. Aside from both front wings missing, the only real omissions were the engine, differential, wheels and exhaust system.
So that’s where this project starts really: a rolling E46 M3 in need of a new engine. Having successfully purchased the shell, attention turned to finding a donor engine. From the outset I’d decided that I wouldn’t simply bolt in a replacement; whatever went in there would have to be a little special. A donor engine was quickly sourced, albeit one with a cracked piston, and a full strip down commenced. Further damage was found upon stripping the engine down, with scoring to the cylinder walls and a number of big end shells showing alarming levels of wear. The big end below the cracked piston was the worst, with a bit of damage showing on the crank. Problems already, but none that can’t be overcome!
With the engine fully stripped-down anything that was remotely suspect was binned, whilst anything that looked usable received a thorough inspection. Whilst the oil pump was apart the engine received its first upgrade: a #VAC-Motorsport upgrade kit supplied by #Hack-Engineering . With a redesigned shaft, sprocket and fastening mechanism, the upgrade kit safeguards the oil pump from the two main failure mechanisms: the shaft shearing or the nut loosening off in operation. With a lot of time and effort going into the engine, oil pump failure certainly wouldn’t go down well and would almost certainly damage the engine beyond repair. The money spent here safeguarding the rest of the engine is money well spent in my book!
Over the next few months the engine will be built back up, with careful component selection and detailed analysis taking place to ensure everything runs perfectly. Having spent most of my career working as a design engineer for a race engine manufacturer I’m hoping to share a little bit of engineering insight as I work through the project, including designing my own set of custom cams.
/ #BMW-M3-E46 / #BMW / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46 / #BMW-M3-Coupe / #BMW-M3-Coupe-E46Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationPANDEMMONIUM
Sam Huggins is a clear thinker. He wanted an E46 M3 with the UK’s first Rocket Bunny Pandem kit, he wanted it to be the only one on Squared wheels, and he made it so. It’s a hell of a way to cause a ruckus. Words: Daniel Bevis. Photos: Matt Woods.
Rocket Bunny E46 M3
Overthinking. It’s the modern curse. We have too much information available to us these days, we’re being constantly bombarded with reams of impenetrable data from all corners of the globe (not that globes have corners…), and we’re essentially spoiled for choice. We’ve reached saturation point; we don’t have time to absorb a new idea before a fresh one elbows it out of the way and starts jumping up and down yelling ‘look at me, look at me!’, and is then immediately bumped for something else. Previous generations never had to worry about this. In a world before smartphones, the internet, and all the other modern buzzwords that your grandpa still enunciates as if they’re spelled in all-caps, information arrived via word-of-mouth and the ten o’clock news.
Everything today is just too fast-paced. Okay, we know what you’re thinking: we sound like relics from a bygone age. Get with the programme, fogeys. But thankfully we’re not alone in this quasi-despair at the pace of digital evolution. Sam Huggins is on board with this antiquated way of thinking. For while his E46 M3 may feature bang-on-trend additions, he hasn’t overthought it. It exists merely as a snapshot of what he wants it to be, no more, no less.
Unpretentious, uncomplicated, and honest. “I’ve been a fan of #BMW s for about ten years,” he says. “I think they’re superior to other makes in that you can squeeze more fun out of them; in that sense they represent very good value for money.” Well, he’s on to something there. And an early sighting of a Phoenix yellow E46 M3 in a showroom was enough to light the blue touch paper for Sam. “I fell in love with it, the colour was amazing,” he enthuses. “I’ve since had an E92 M3 as well, but I came back to the E46 for this project because I decided that I preferred it.” See, there’s no mucking about here. He’s laser-guided, like the Terminator. “My first car was a Corsa,” he goes on, “but my dad wouldn’t let me modify cars at all. It was when he passed away that I started modifying, about five years ago.”
This isn’t a mercenary act of rebellion, merely a statement of fact. You’ve probably gathered by now that Sam’s a goal-oriented guy; he identifies what he wants, then he makes it happen. So it is with this M3.
“I found the car on Pistonheads,” he explains. “It was totally stock, and in mint condition, and I basically bought it because I wanted to learn to drift.” Such incendiary words are bound to reduce vast swathes of dyed-in-the-wool purists to quivering heaps of apoplectic grumbling, but he didn’t build this car for them – he was working to a checklist in his head, and the first thing on the list was the wheels.
“At the time, these were the wheels to have,” he grins. “With hindsight perhaps it would have been nice to have some custom Rotiforms built so I wouldn’t have to run spacers, but…” [he ponders reality for a moment, then the light bulb above his head re-illuminates] “…no, these are definitely the right wheels for the car. I can say that I’m the only one running on #Squared SD2s.”
They’re pretty mighty too. Forged threepiece splits with an acre of dish on the rears, artfully colour-contrasted to highlight how the inky black spokes seemingly plunge into a gigantic bowl of custard against the menacing black of the wide-hipped body. Naturally you can’t just bolt a set of 11”- wide wheels on the back of your E46 and expect everything to be sunshine and roses.
The arches won’t thank you for it. So Sam had a decision to make – how does one broaden such a car to accommodate this new-found girth? The obvious answer, it seemed to him, was to make his own body kit: “I made it and fitted it myself,” he says, “although it started cracking before too long, so I decided to do things properly and go for a Rocket Bunny Pandem kit instead. And that’s pretty sick, as it’s the only one in the UK.”
Sam was working on the car when he could over evenings and weekends, so it took around a year before the E46 rolled out on its new rims along with the exotically bulky new bodystyle, but the finished product really speaks for itself. Indeed, the choice of gloss black is a deliberately un-boisterous choice, in deference to the ostentatiousness of a lot of other Rocket Bunny cars, that makes the #M3 almost subtle. Almost, but not quite. It’s very wide and has yellow wheels, let’s not go nuts. And you’ve probably spotted the ducktail spoiler and the roof-mounted vortex generators from a Mitsubishi Evo too – this thing gets less and less subtle the more you pore over the details, it’s like a greyscale Magic Eye picture of a bullfight.
“The car was way too high for my liking, and I couldn’t afford air-ride, so I went for some budget coilovers,” he continues, ticking a further item from the mental checklist. But don’t let the word ‘budget’ fool you into thinking it’s not a considered, quality chassis: just take a peep through the wheels and you’ll spot a K-Sport big brake kit at either end, and the way Sam’s got those coilies wound before the lens gets it sitting just right here.
“I fitted a #K&N induction kit too; it only took about an hour, after I watched a tutorial on YouTube,” he says, again with a supremely focused air. “And I was thinking about doing a full race car interior, but to be honest I ran out of money at that point, so I just went with an extended shifter and a deep-dish steering wheel – all of the budget went on the exterior.” This is no hardship really, as it’s not as if the inside of an M3 is an unpleasant place to be, and that brutal exterior aesthetic really does deliver.
What we have here, then, is a nononsense car built to a specific brief with no messing about. It’s a very efficient kind of fun that fits neatly with the M3’s German roots, with just enough Japanese zaniness to pop it onto the scene’s radar and keep it there. “The Pandem kit is definitely my favourite part of the car,” says Sam. “Just look at it, it’s amazing! And being the only one in the UK, that just makes it cooler.”
He’s not wrong. And having worked methodically through his uncomplicated list of modifications, is Sam now ready to sit back and enjoy cruising around in his exotic new creation? “No, it’s for sale,” he deadpans, “I’m buying a VW Transporter.”
Aha. Okay, we wouldn’t expect him to mince words about the realities of this build. The lesson to take away is that this car was never about following the herd of listening to received wisdom – it exists solely in its own snapshot in time. And that’s a pretty rare thing these days.
“The Pandem kit is my favourite part of the car. Just look at it, it’s amazing!”
DATA FILE #Rocket-Bunny / #BMW-E46 / #BMW-M3 / #BMW-M3-E46 / #Squared / #BMW / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46 / #BMW-M3-Coupe / #BMW-M3-Coupe-E46 / #BMW-M3-Rocket-Bunny / #BMW-M3-Rocket-Bunny-E46 /
ENGINE AND TRANSMISSION 3.2-litre straight-six #S54B32 / #S54 / #BMW-S54 , #K&N induction, six-speed manual with short-shift
CHASSIS 9x19” ET21 (front) and 11x19” ET20 (rear) #Squared-SD2 forged three-piece wheels with 235/35 (front) and 275/30 (rear) tyres, coilovers, #K-Sport big brake kit (front and rear)
EXTERIOR Gloss black, Rocket Bunny Pandem wide-arch body kit, ducktail spoiler, Mitsubishi Evo roof-mounted vortex generators, fibreglass front wings
INTERIOR #OMP deep-dish steering wheel, extended gear shifter
“These are definitely the right wheels for the car. I’m the only one running on Squared SD2s”Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationWith killer styling, perfect stance and an S54-swap , 2M Autowerks’ E46 is an absolute feast of awesomeness. Words: Elizabeth de Latour. Photos: Viktor Benyi.
Werk it 2M S54 E46 Spectacular Stateside #M3-powered , metal #wide-body-3-Series.
We’ve been around for a long time. We’ve seen a lot of modified cars over the past 19 years (and 209 issues) but we love the et excited by some of the cars we come across. It’s a sign that we’re still in the right job and a sign that you out there in modded #BMW land are doing something very right. And it doesn’t get much more right than 2M Autowerks’ painfully good E46.
This is the sort of car that leaves you a little bit breathless. It’s the sort of car you can spend forever looking at and never get bored of. It’s the sort of car that just feels so utterly complete that it makes you question everything you thought you knew. You’re probably feeling exactly that way right now; don’t deny it…!
The man behind this build, and one half of 2M Autowerks, is David Mendoza – a self- confessed petrolhead through and through. And, unlike a lot of the big show builds we come across, this E46 is his own personal car which he’s owned for 16 years now. It’s that sort of long-term attachment and commitment to project cars that always makes us feel warm inside. “I’ve been into BMWs ever since I could remember,” says David, “but once I was able to purchase a car and actually be behind the wheel, that’s when it became even more special.” We can see how stepping from a hand-me-down Toyota 4x4 into an E46 would have felt very special indeed. “I absolutely loved the lines on the E46 and knew I had to have one,” he says. “Ideally I wanted to get an M3 but at the time I was two years into college at San Diego State University and knew my limits, so I had to settle for the #BMW-330Ci-E46 .” And while it may not have been an M3, the #330i is such a sweet package that, as far as compromises go, it barely counts.
It all began, as these things so often do, with some simple mods and while David did have a plan, it didn’t pan out as he envisaged. “When I bought the car it was Jet black and the first thing I did was get rid of the amber corners, reflectors and side markers,” he says. “At first I started with just simple exterior modifications: wheels, tyres, clear lights, springs, and a Dinan cold air intake. I left the car like that for years and years.
Then my brother and I opened up 2M Autowerks and I started to play around a little more with the cars. I ended up basically doing everything and anything I could.” He’s not kidding…
This is one of those builds where there’s so much amazing stuff going on that it’s difficult to know where to start but seeing as the first thing that hits you is the styling, let’s start there. One of the many, many things that we really like about David’s E46 is that he’s not gone down the default Sport or M3 bodystyling route; yes, there are a few elements but the car has retained its SE essence and this is bolstered with rather a lot of custom work. The front and rear bumpers are both SE items but here they’ve been enhanced with Hamann lips that have been blended in, resulting in a perfectly smooth and unique look that makes a refreshing change from the norm and gives this E46 a bold, distinctive presence. The M3 bonnet works really well with the car’s overall look and is matched to a pair of M3 mirrors, still arguably the best-looking E46 mirrors about, and M3 side skirts to fill out the car’s profile. What you might not realise is that those front arches are also M3 items; David has had the side vents welded shut for a much cleaner, smoother look which definitely seems to be the theme with this E46. The most impressive part of the whole is, without doubt, that fat, all-metal wide- body rear end with its massive pumped-up arches. They really endow this E46 with monster road presence. It’s a great combination of styling elements and the whole package is complemented by a dazzling Imola respray – which we think is far more suited to a head-turning build of this calibre than blend-in black.
All this would be for nought, however, if David had fallen at the wheel hurdle, but there never really was any danger of this happening considering the rest of the work going on here. “Back in #2002 , I initially went with an OEM+ size and a set of staggered 19” iForged Senekas,” says David. But once the wide-body conversion had been completed, the 8.5” and 9.5” widths just weren’t going to cut it. A three-piece wheel with a stepped lip was at the top of his shopping list and that’s exactly what we’ve got here. You’re looking at a gorgeous set of Aristo Forged MJKs, a size down at 18” across but massively wider to fill out those newly pumped-up arches, 9.5” wide up front and a serious 11.5” at the rear. They’re finished in custom matt Oro paint, which looks perfect against that bold red body.
The car’s stance is no less perfect. The killer ride height has no air behind it, however, as this E46 is all static, slammed on a set of Status Gruppe SRS coilovers which bring the arches to within a whisker of the tyres. In addition David has fitted a set of UUC anti-roll bars.
Now, the #BMW-330Ci is a brisk machine, powered as it is by BMW’s rather wonderful M54. But considering everything else going on with this project, it was never really going to cut it especially with David’s long- standing desire for an E46 M3. As good as the M54 is, the S54 is just a bit better – so that’s what you’ll now find in the engine bay. Once glance at that engine, however, will tell you that it’s most definitely not standard.
And that’s because just an engine swap wouldn’t have sufficed; David wanted to extract maximum power from that awesome straight-six. Up top, there’s a set of custom 2M Autowerks E46 velocity stacks handling the intake side of things, with an Alpha N tune by RK Tunes along with a set of Turner Motorsport pulleys. At the other end of the engine you’ll find set of 2M JSP custom stepped race exhaust manifolds which connect to a UUC TSE1 exhaust. David also fitted an Earl’s oil cooler and a Mishimoto high performance radiator, which has since been changed for a CSF race rad. It’s not just the engine that has been worked on; the engine bay too has been given plenty of attention to ensure that this E46 turns as many heads with the bonnet off as it does with it on. David carried out a wire tuck and then welded up any excess holes for a super-smooth look. Then he added a custom cabin air filter and brake covers, before finishing the engine bay off in cement grey, which delivers a striking contrast to the bold and bright Imola bodywork. The cement grey really was an inspired choice, and is not what you expect to see when the bonnet is up, or off, and it definitely makes you look twice. With the engine swap completed the E46 had the performance it deserved but, as the old adage goes, power is nothing without control, and so the stock front brakes were removed and replaced with a pair of substantial Porsche 996 calipers, though you’ll be hard pushed to spot them as they too have been painted in cement grey with just a red Brembo logo, making this possibly the most discreet BBK setup we’ve ever seen. The calipers themselves sit on Rally Road brackets and are mounted around ECS tuning two-piece CSL discs with braided hoses for good measure.
You might think that after all that, by the time he got to the interior David may have run out of steam, but you’d be dead wrong; he’s really gone to town in here. Step one: the seats. The stock items have been unceremoniously ejected and replaced with a pair of utterly gorgeous Recaro Speed items finished in black leather with red stitching.
They are joined by some choice Alcantara items which include a Colby handbrake gaiter and gear gaiter (both with M tricolour stitching), plus a Colby Alcantara steering wheel with matching stitching and a red centre stripe. The front doorcards and rear side panels are gorgeous CSL carbon fibre items, while the rear is dominated by an Autopower half-cage with harnesses and topped-off with a custom rear seat delete. The finishing touch is a splash of Oro paint on a few trim areas and the cage itself, which adds a unique touch of colour.
It’s impossible to dislike an E46, they’re such good cars. And this is arguably one of the best we’ve seen. David has clearly poured a vast amount of money and love into it and the end result is so complete. Well, other than the addition of a carbon roof, which David will fit in a few months. Once that’s on, this car will be completed for good – and it’s rare to be able to say that about any project. David has already started on his next build, an S85 V10-swapped E46 track car, as well as an E36 PTG-style track car, but don’t worry, this E46 isn’t going anywhere. All that’s left for David to do now is ‘werk’ it. Lucky chap!
TECHNICAL DATA FILE #2M-Autowerks / #BMW-E46 / #BMW-M3-E46 / #BMW-M3 / #BMW-M3-2M-Autowerks / #BMW-M3-2M-Autowerks-E46 / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-M3 / #BMW-3-Series-M3-E46 / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46 / #Aristo-Forged /
ENGINE AND TRANSMISSION 3.2-litre straight-six #S54B32 / #S54 / #BMW-S54 #S54-swap , #2M-Velocity stacks, #2M-JSP custom stepped race exhaust manifolds, #UUC-TSE1 exhaust, #Alpha-N tune by #RK-Tunes , wire tuck and excess holes welded, engine bay painted cement grey, custom cabin air filter and brake covers, Earl’s oil cooler and fittings, #Mishimoto high performance radiator (now CSF race radiator), #Turner-Motorsport underdrive pulleys, six-speed manual gearbox, #UUC short-shift kit
CHASSIS 9.5x18” (front) and 11.5x18” (rear) #Aristo-Forged-MJK three-piece wheels in custom matt #Oro-paint with #Motorsport-Hardware 70mm (front) and 90mm (rear) stud kit, 255/35 (front) and 295/30 (rear) Falken FK453 tyres, #Status-Gruppe-SRS coilovers, #UUC anti-roll bars, Porsche 996 brake callipers (front) painted cement grey with red #Brembo logo on #Rally-Road brackets, #ECS-Tuning two-piece #CSL discs, stainless brake hoses
EXTERIOR Full respray in Imola red, Hamann front lip blended onto SE front bumper, black kidney grilles, M3 bonnet, M3 front arches with side vents welded shut, M3 mirrors, M3 side skirts, custom all-metal wide-body rear, Hamann lip blended onto rear bumper
INTERIOR Recaro Speed front seats with custom leather and red stitching, Autopower half-cage painted in Oro with harness, CSL carbon fibre front and rear doorcards, Colby Alcantara steering wheel with and red centre stripe, Colby Alcantara handbrake and gear gaiters with M tricolour stitching, multi-touch- screen head unit, Oro painted trimStream item published successfully. Item will now be visible on your stream.
- Post is under moderationTariq Vadgama / #BMW-E46 / #BMW-320Ci-Sport / #BMW-320Ci-Sport-E46 / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46 / #BMW-320Ci-E46 / #BMW-320Ci / #BMW
Five years ago Tariq treated himself to a gorgeous Imola red E46 320Ci and the ensuing half decade has seen him take it from standard to decidedly not-standard. It’s been lowered on a set of FK coilovers and when we say lowered we mean lowered, with Tariq winding them all the way down front and rear. The front and rear bumpers have been smoothed, the bonnet has been debadged and the grilles have been colour-coded. When it came to wheels, Tariq didn’t want to go aftermarket, so he’s added a set of 18” Style 32s from an E38 while inside, the cloth interior has been replaced with a leather one from an M3 in Kiwi. Tariq says he took a risk with the colour but he loves the end result and we have to agree.Stream item published successfully. Item will now be visible on your stream.