Buyer’s guide Bristol 401-403

Buyer’s guide Bristol 401-403. The aircraft-maker’s finest car was the executive jet-setter of its day, as Malcolm McKay explains. Photography Tony Baker.

Bristol’s 401-3 was outrageously expensive for a 2-litre saloon in its day-only the likes of Bentley, Rolls-Royce and Lagonda cost more in 1949 – but it feels like a spacecraft in comparison to most of its contemporaries. A stiff chassis, effective suspension, smooth and powerful engine, plus a lightly built yet well-insulated body combine to make a car that feels taut, lively and sophisticated. Some would argue that Bristols only went downhill from here, losing their streamlined styling, gaining weight and retaining ‘advanced’ engineering until it became archaic.

Elegant Bristol 402 Convertible, first owned by Stewart Granger.

Bristol 401 with imposing backdrop of Brabazon at Filton factory.

The heart of the car’s success was its pre-war BMW-derived hemi-head straight-six, a superb unit, intelligently developed by Bristol, that was sought-after for sports and racing cars at the time. But Bristol made the most of it in the 401. The first 2-litre production saloon to hit 100mph, its all-aluminium body was exceptionally aerodynamic, helped by push-button door opening and internal bonnet/boot releases. Bristol adopted Carrozzeria Touring’s Superleggera construction long before Aston Martin. Even the gauge of aluminium varied: 16 for the tops of the front wings and the bonnet, where pressure might cause dents in a thinner gauge, and 18 elsewhere. Contoured, body-coloured bumpers with chrome inserts, mounted to the chassis via rubber blocks, were decades ahead of their time.

Other clever details include a bonnet that opens sideways (which is safer) in either direction, or can be removed by undoing a bolt, and a bootlid with a spring-assisted strut. Early 401s even had Tufnol floor and engine bulkhead, later replaced by steel. Where the alloy panel edges were wrapped around the steel tubes at the lower parts of the body, however, the sacking between gets wet and electrolytic corrosion can occur. Letting in new metal is the only cure. The paintwork is critical, too: check that it has been done properly, not blown over (which will flake off).

The rare drophead 402 attracted Hollywood stars, early examples going to Stewart Granger and Jean Simmons. In 1953 the 403 refined the idea, its engine boasting a stronger crank and larger valves, with greater oil capacity, to give 100bhp and power the car to 106mph. It boasted fresh-air or recirculated heating/ventilation, automatic reversing lights, multi-adjustable seats and an alloy petrol tank. Bristol phased out the 403 in 1955 after introducing the close- coupled 2+2 404 followed by the four-door 405.

On the road

The Autocar was hugely impressed by the 401’s comfortable 80mph cruising when tested in 1949, and by ‘handling qualities very much above the average’. Only the heavyish brakes (improved on 403) were criticised. Dunlop front discs (with servo) became optional on the 405 and are often retro-fitted on 401/3. A Coopercraft four-pot disc conversion is also available, but care must be taken to get the balance correct with rear brakes.

Having a good engine is critical: rebuilds are costly. Check which unit is in place, because upgrading to later, more powerful ones is not unusual; 40Is should have 85C engines and 403s 100As, but you may well find alternatives such as the 125bhp 100D2, the more torquey 2.2-litre 110-series or the 130-155bhp BS (Bristol Sports) motor. The engine should be driven gently until warm – check that the vendor does – and when oil is at 70°C, should show 60psi oil pressure at 3000rpm. Well cared for, these sixes ought to last 100,0 miles between rebuilds.

One-shot chassis lubrication (every 100 miles) needs checking to ensure that the pipes haven’t become blocked. Some oil dripping is to be expected, but confirm that it is not leaking from rear axle hub seals, which are a pain to replace.

Inspect the loom, because only two circuits are fused and it’s pricey to renew. Semaphore trafficators are often replaced with flashing indicators – the function built into the spodights and reversing lights to avoid adding extra lamps.

Bristols were built to take crossplies, but work well on Michelin X radials, Pirelli Cinturatos or Vredesteins. Heavy taxi tyres spoil die feel.

OWNER’S VIEW

Mike Davies

“I always liked Bristols since they were new,” recalls Davies, “and remember Setright writing about them. I’ve owned various classics and had a Scimitar when I bought this 403 in 2001, but soon found I wasn’t using the Reliant. It has the disc brakes and overdrive, and feels so modern for its time. The performance, handling and steering are not like driving a ’50s car: it keeps up with modern traffic and cruises at 70-80mph on the motorway. I’ve fitted Mahle pistons – the rings and grooves were worn in the old ones – and put fresh bearings in the gearbox plus a new clutch. I enjoy working on it. but had to get Bristol Cars to fit the new headlining! I’ve also reset the carbs; the jets used to work loose. We’ve driven it to France and Spain on holiday.”

The knowledge

WHAT TO PAY

402 and coachbuilt tourers

Show/rebuilt 401/3

Average 401/3

Restoration 401/3

PARTS PRICES

Rear chassis extension (make + fit) £500

Front bumper (make + fit) £2-2500

Rebuilt engine £14-20,000

Water pump £660

Triple Solex carb rebuild £425

Rebuilt gearbox £3600

Brake master cylinder £130

Brake shoes (front axle set) £80

CLUBS

Bristol Owners’ Club boc. net Bristol Owners’ & Drivers’ Association bristoloda. org

BOOKS

Bristol Cars 1946-2012 Brooklands Books Bristol Cars A Very British Story Christopher Balfour, Haynes Bristol An Illustrated History

Charles Oxley, Crowood

SPECIALISTS

Spencer Lane-Jones 01985 847133 Bristol Cars 020 8560 3300 Brabazon Motors

0117 951 8726 Brian May 0121 430 3767 Ian Nuthall 0115 978 063 Mitchell Motors 01747 820223 Andrew Blow 01672 539689 Derek Hughes Overdrive Kit 01642 654328

TIMELINE

1948 Oct 401 and 402 launched: 400 chassis and 85C engine, new, more spacious, aerodynamic Superleggera body (400 continues).

1950 401 Second Series: Brivadium dry liners in cylinder block, improved cooling, optional oil cooler, freer-flowing exhaust, plain (not pleated) leather seats, chrome inserts not rubber in bumpers, bigger lip over top of dash. 402 production stops (21 built): also 400 ends 1951401 Third Series.

1953 May 403 replaces 401 (618 built): 100bhp 100A engine, front anti-roll bar. Alfin drums all round (later finned iron rear); 404 short- wheelbase 2+2 also launched.

1954 Four-door 405 joins the family.

1955 Final 403 (281 built); last 12-15 had 100B2 engine. CR up from 7.5:1 to 8.5:1,105bhp, sidelights on top of front wings, rear reflectors.

FACTFILE

INSURANCE

£157.94, for a 30-year-old Londoner with full no-claims bonus and a clean licence on a ’54 403 as a second car, agreed value £40,000, garaged overnight, 5000 limited miles. RH 01277 206911.

THE ALTERNATIVES

AC 2-LITRE

Venerable ohc ‘six’ in a leaf-sprung alloy-on- ash two-door saloon was refined, but lacked Bristol’s performance and modernity; also made as rakish Buckland tourer, DHC and four-door saloon. Sold/no built 1947-58/1129 Mpg 20-28 0-60mph 19.9 secs Top speed 80mph Price new £1456-1636 (’53) Now £8-15k (saloon)

HEALEY ELLIOTT/ WESTLAND/ TICKFORD/ABBOTT

The 2.5-litre Riley ‘four’ wasn’t as smooth as the Bristol ‘six,’ but was potent enough with light alloy bodies. Appealingly sporting, with great heritage. Sold/no built 1946-’54/466Mpg 18-26 0-60mph 14.6 secs Top speed 104mph Price new £1726-1797 (’53) Now £40-75,000

One to buy

Price £47,000

Year of manufacture 1950

Recorded mileage 35,151

Vendor Oselli, Great Horwood. Bucks; tel: 01993 849610; oselli.com

For Superb rebuilt condition

Against Minor oil leaks; indicator fault

Chassis 401/807 with engine 85C/1972 was restored by Brian May between 2005 and ’08 at a cost of more than £35,000. It didn’t appear to need any new metal once the paint was off, and is now nice and straight with excellent door fits and shiny fresh paint. Looking down the sides reveals a few gentle ripples although that’s normal. The chassis and sills are solid and there’s a recent part-stainless steel exhaust, plus a few oil drips from engine, transmission and rear axle.

Inside, the leather, carpets and headlining are all unworn, plus the dash timber and instruments are mint. The only tiny faults are an indicator lever that needs a grubscrew to secure it, and the driver s door lock handle is broken off.

The engine is smart and tidy, with cleanish oil and slightly brown coolant to the right level in the top tank. The original jack is still strapped to the bulkhead, and there’s a spin-on oil filter conversion, with fluid and level okay.

It starts easily and drives sweetly with strong synchros. The steering is properly fluid and the brakes nip up well. Oil pressure is 60psi, rising to 70psi with any revs, with temperature steady at 85°C. The indicators light if you twist the switch spindle, but they don’t flash (to be investigated).

The history file contains much correspondence over the restoration and an original green continuation logbook issued in die 70s. The last MoT test was carried out in 2012.

Who else but an aeroplane builder such as Bristol could manufacture a streamlined saloon that looks as good as a 401-3?

{gallery}401{/gallery}

Engine is in fine order, with spin-on oil-filter conversion.

All the chrome is pristine; lots of tread on Austone radials.

Signature Bakelite sports wheel fronts stylish dashboard.

Our verdict

Early Bristol saloon prices are rising fast as their exclusivity and quality are finally being recognised: buy a good one and you will not regret it. Beware down-at-heel cars – they were cheap for a long time and many owners couldn’t afford the high parts and repair costs. Neglect of the body and engine lead to severe restoration costs, so choose a project with caution.

FOR

•             Superb performance for a 1950s 2-litre

•             Delightful details and quality throughout

•             Practical for everyday use or long tours

•             Comfortable and quiet, with fine handling

AGAINST

•             Superleggera body is expensive to fix and paint

•             Complex cross-pushrod engine is pricey to rebuild, and can disintegrate through age

•             Specialist nature means costly parts and repairs

Beautifully balancedshape of 403 is basicallythe same as 401, but thefine proportions were lostin the restyled and less-streamlined 405 four-door.

Check for cracked block on right-hand side; it costs c£2500 to repair. Skimming the alloy cylinder head can drastically raise compression; listen for pinking and inspect for signs of overheating or head-gasket leaks. If the radiator is more than 10 years old, it should be recored and the engine coolant passages cleaned out.

Axle oil lubricates the torsion-bar link arm pivot bearing; if it wears, the oil leaks out. This, plus rear hub leaks, can wreck the axle if left to run dry.

Bristol-made gearbox is sturdy and can invariably be rebuilt. Adding a compact J-type overdrive is worthwhile; the kit requires no chassis modifications.

Steering and suspension wear if neglected: look for signs that one-shot lubrication works and has been used, and that springs have leather gaiters.

Drum brakes are okay on 403s (but fade on steep descents); 401’s are heavy. Front discs and a servo can be fitted. Repro master cylinders vary in quality.

Leather-upholstered seats are comfy and front backrests can be set to four angles. A full retrim costs £12k and the thickness of factory hide is unavailable.

Instruments can generally be rebuilt if complete; second-hand ones can be found. Check wood all matches and is good; replacement is relatively easy.

1 Aluminium fuel tank where it’s held by steel straps.

2 Steel/aluminium corrosion across front apron.

3 Corrosion along the sills and over wheelarches.

4 Main chassis legs.

5 Chassis outriggers.

6 Rot behind B-posts.

7 Rear inner wheelarches.

8 Rear chassis extensions.

9 Double-skinned steel panels each side of the spare-wheel tray.

10 Corrosion above rear bumper.