Toggle Sidebar
News Feed

#VW

Currently filtering items tagged with #VW


  • Post is under moderation
    CAR #VW-Beetle / #VW / #Volkswagen-Beetle / #Volkswagen / #Volkswagen-Beetle-MkI

    RUN BY Martin Port
    OWNED SINCE March 2011
    PREVIOUS REPORT May 2017

    Some cars just don’t get the love they deserve, and I’m embarrassed to admit that the Beetle is definitely one of them. It has given reliable service for years now and, despite my many promises to carry out major work, I’ve failed to deliver. Even worse, it took the failure of the MoT test to propel me into action, and even then it was at the pace of an anaesthetised sloth.

    What did it fail on? Surprisingly, it was really ‘only’ some rust (and a broken anti-roll-bar clamp). I’d seen much worse, but its proximity to the rear suspension mounts meant that it was an immediate ‘x’ in the box. So, the Beetle was back in the garage while I examined the options for repair. Since this coincided with winter’s first dusting of grit on the roads, I deliberately didn’t hurry – though it’s too late to take evasive action, of course.

    Eventually, once I’d cut out the rot, my brother-in-law Pat crafted some repair sections and we set to work. Between us we welded in the fix, which was a tricky under-seat corner piece, but while I was inspecting inside the wheelarch I noticed some more rust.

    I cleaned up and welded in a couple more off-cuts of steel from Pat’s workshop, and applied seam-sealer to the inner repair. That meant I now had to underseal the inner arch, which I knew desperately needed doing to the entire underside. Fortunately, it’s still in remarkably solid condition.

    I’ve used Dinitrol before and found it to be very effective, so opted for the same again this time. Without a compressor rigged up at home currently, I plumped for several 500ml cans of its 4941 aerosol because I knew it would be fairly simple to apply where needed. Getting the Beetle up in the air was easy thanks to my old set of ramps and large axle stands, offering just enough clearance for a good wire-brushing of the underside.

    Then it was time to put the Dinitrol to good use and slowly apply it to the underneath of the vehicle and into the wheelarches. An hour later I was very pleased with how the floorpans looked. Compared to using a schutz gun in a confined space, the aerosol allows you to get into all the smaller areas with ease – perfect if you don’t have access to a four-post lift.

    With the welding done I sent my spare set of period wheel rims to Berkshire-based company Procoat to be blasted, primed and powdercoated.

    A five-minute chat with the owner turned into an hour as his enthusiasm for classics became obvious, having been given the name Aston Martin by a father with a clear sense of humour. It’s little wonder that not only does he now run a company that specialises in blasting and coating car parts, but he also owns several Astons.

    Having heard him wax lyrical about what makes a good process and the importance of how many microns of coating you need on a rim, it was nice to see the fruits of his expertise when I collected the finished wheels. The gloss black is fantastic, and the finish almost mirror-like – the colour isn’t standard, but our choice for the Beetle.

    We had agreed to help Vintage Tyres out by evaluating some whitewall rubber, so these were fitted, and suddenly the combination of new tyres and shiny rims put the rest of the car to shame.

    It might be back on the road, but it looks as if the bodywork and a respray have to be the next steps.

    THANKS TO
    Procoat: 01635 200017; www.professionalcoatings.co.uk
    Dinitrol: www.dinitroldirect.com

    Whitewalls always provoke a ‘Marmite’ response, but even if they stay on just for the summer, they certainly look the part when coupled with the freshly painted rims.

    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    Volkswagen Golf GTI 16v (Mk2) From wondering what he’d just bought to its transformation into trackday perfection, Aston Parrott’s Mk2 GTI has been a car he’ll never forget.

    / #VW-Golf-II / #VW-Golf-Mk2 / #Volkswagen-Golf-Mk2 / #Volkswagen-Golf / #Volkswagen / #VW-Golf / #VW-Typ-1G / #VW-Typ-19E / #Volkswagen-Golf-Typ-19E / #Volkswagen-Golf-II / #VW / #VW-Golf / #Volkswagen-Golf / #Volkswagen-ABF / #Volkswagen-Golf-GTi / #Volkswagen-Golf-GTi-II / #Volkswagen-Golf-GTI-Mk2

    End of term Fast Fleet

    After six brilliant years of ownership, the time had arrived to say goodbye to my Mk2 Volkswagen Golf GTI 16v.

    I can still remember the day my dad and I drove to view the car in Somerset. The plan was to purchase it and then for me to drive on to south Wales where I was studying at university. Luckily for us the GTI was as described and the deal was done.

    Driving over the Severn Bridge I went to move the knob that adjusts the side mirror and it fell off in my hand. I instantly started laughing and thought to myself: what have I just spent my student loan on? The GTI was replacing an Audi A3 Sport as my everyday car…

    The simple interior design was new to me, but I instantly fell in love with the Golf’s character and the sound from its 139bhp 1.8-litre 16-valve engine. My girlfriend was waiting in the university halls to see what monstrosity I had just bought, and I was expecting a negative response to the older, no-luxuries GTI, but to my surprise she loved the boxy design just as much as I did.

    Over the next three years the GTI was used nearly every day, in all weathers and for any occasion, from tackling heavy snow to long weekends away with a boot full of camping equipment. It became part of the family and was the perfect car, demonstrating why hot hatches are so popular. Nevertheless, being an older car – and one that I would take to over 180,000 miles – life wasn’t always easy and many parts had to be replaced along the way, including the gearbox. There was also the odd bit of welding. But somehow I could always forgive its troubles because I just worshipped the way it drove.

    After graduating I got my dream job as staff photographer at Drive-My and the GTI was no longer needed as my daily driver. So as the car made its debut in Fast Fleet in mid-2015, I began turning it into my perfect GTI. Without the need for it to be so practical, I slowly transformed it into a more driver-focused Mk2, stripping the interior and adding a carbonfibre bonnet and tailgate, uprated suspension and Recaro SPG bucket seats. My Golf was also the first car I had driven on track for any decent amount of time. I remember one lovely summer’s evening – my birthday, in fact – at Rockingham and thinking it was just perfection. Despite its modest power, the car’s light weight and general set-up ensured it was quick enough not to embarrass itself.

    Driving a Mk1 Golf GTI to the Wolfsburg factory with Drive-My staff writer Antony Ingram really enlightened me as to just how good the Mk2 was. It had better brakes than its predecessor, was faster and had power steering and more headroom. We made the return trip in the then new Mk7 Golf GTI Clubsport Editon 40. This and the further honed Clubsport S are two of my favourite modern hot hatches, so much so that I stole the S’s idea of replacing the rear seats with a boot net for my own car.

    So why have I sold my Mk2? Mainly down to a lack of parking space and because I simply wasn’t driving it as much as I used to – my 993 Carrera being partly to blame for both of these. So I advertised the GTI online one evening, and the very next morning I got a call from avid Drive-My reader Simon Murray, who explained that he had been following my Fast Fleet reports and had to own the car.

    A few more messages and another phone call later and he had secured the car with a deposit, booked a one-way ticket from Scotland and was ready to collect ‘my’ GTI. It all happened very quickly, but I was very happy it was going to a good home.

    I collected Simon from the airport on a Saturday morning and we chatted about our passion for cars. After a drive in the Golf, resulting in a big smile on Simon’s face, the paperwork was signed, a quick photo was taken of the handover, and the car was gone. But it’s left me with so many good memories.

    Aston Parrott

    Date acquired April 2012
    Duration of test 6 years Total test mileage 11,000
    Overall mpg 29.5 Costs £6089 since Drive-MY (July 2015), including carbonfibre bonnet and tailgate, paint, seats, suspension, tyres and MOTs Purchase price £3500
    Value today £8500

    ‘The GTI was used nearly every day, in all weathers and for any occasion’
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    Car #VW-Beetle / #VW / #Volkswagen-Beetle / #Volkswagen / #Volkswagen-Beetle-MkI
    Run by Martin Port
    Owned since March 2011
    Total mileage 87,698
    Miles since February report 1053
    Latest costs £137

    SERVICE TIME FOR MISFIRING BUG

    The Beetle had been doing what was asked of it for some time without any purposeful maintenance, so it came as no surprise when it suddenly developed a misfire one day without warning. A cursory look failed to throw up anything obvious, so I figured that it was time to carry out a full service and see if that resulted in an improvement.

    VW Heritage markets a kit that includes plugs, leads, distributor cap and rotor arm (the car is already running a points-less ignition system), but I knew that I also needed to check the valve clearances, and that was a slight issue.

    With no replacement for the C&SC workshop in sight, my own garage out of action thanks to ongoing construction work, and the driveway full of building materials, I was faced with carrying out the service at the side of the road.

    I’m no stranger to kerbside maintenance but, with a wet winter in full swing, the thought of having to check the clearances while lying in the gutter didn’t appeal much. I was always going to be tempted by an offer from friend and Our classics regular Oli Cottrell to do the job in exchange for a few notes!

    When he delivered the car back to me, he was full of praise for how it drove – an assessment that I was pleased with, given that he worked for a time at a classic VW specialist. As suspected, the valve clearances were out and one had closed up, but with everything adjusted the Beetle was full of pep once more… until the following day, when a text from Mrs P read: “Fine going into town, but stuttered all the way back.”

    Sorting a loose ignition lead helped a little, but we also decided to look at the carburettor settings. The manual suggests that the volume control screw needs to be somewhere between two-and-a-half and three turns out, but this one was at six, which would explain the black electrodes on the new plugs. After a road test, we settled on three turns and, with a tweak to the air bypass, normal service was resumed.

    Typically, with the Beetle ousted from its cosy garage, the cold snap took its toll and killed the battery. That was easily sorted with a visit to the auto factor, but outdoor living is also proving detrimental to the chrome. That is disappointing, because it isn’t even a couple of years old – raising the issue of quality when it comes to parts. With that in mind, when the wash/wipe switch appeared to fail, I was about to order an OEM replacement, but decided to check the rest of the system first. It turned out that the switch was fine and that the upper pipework and nozzle were gummed up.

    After dismantling the whole assembly from the water tank upwards and repeatedly sucking out all the muck, the washers function again – but in the process I had succeeded in drowning the adjacent radio. It now only partially works, and out of only one speaker. I’ve never been particularly enamoured with this unit, though, so plans are afoot to conceal an alternative in the glovebox and reinstate the dashboard blanking plate.

    With the underbonnet area emptied to attend to the washers, I noticed that the pipe from the fresh air box had disintegrated. This is meant to enable water to drain out, helping to reduce condensation on the windscreen. If, however, the pipe is absent or broken, water just collects in a pool above the fuel tank and will quickly corrode the metal. A new one was bought for £11 and so this is at least one part of the bodywork that won’t be disappearing anytime soon.

    THANKS TO Oli Cottrell: 0118 971 2091 / #VW-Heritage : 01273 444000; www.vwheritage.com


    Not a Californian sunset, but sunrise over a multistorey in Twickenham. Inset: replacement air box drain tube will help to prevent corrosion.

    Air box removed to access washer system Recent chrome already attacked by rust. Pipes and jets were thick with black gunk. Oli doing his best James Herriot impression while attempting to solve the ongoing misfire.
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    GRANDE DESIGNS Mk5 GTI gets big wheels, big brakes and a big attitude. It’s kind of a big deal.

    SATIN YELLOW #Volkswagen-Golf-GTi / #Volkswagen-Golf-GTi-Mk5 / #Volkswagen-Golf-Mk5 / #VW-Golf-V / #Volkswagen-Golf-V / #Volkswagen-Golf-Mk5 / #VW-Golf-Mk5 / #Volkswagen / #VW / #VAG / #Volkswagen-Golf / #VW-Golf / #Volkswagen-Golf-GTi-V

    Volkswagen Mk5 Golf GTi “I wasn’t going to do much to it, honest.” How many times have we heard that one? Ricky Grande is the latest person to roll out that line in front of our cameras… Words: David Kennedy. Photos: Anna Richardson and Keith Sowden.

    “You can write Ricky’s Mk5 feature this month Dave,” said Elliott as we put the plan together for this issue, “it makes sense, you wrote his last one didn’t you?” Yeah, I did, way back in 2008 when I was only a year into my tenure with PVW.

    Back then I had no idea I’d still be doing this almost a full decade later, heck, I was surprised Elliott hadn’t seen through my nonsense at that stage and I was still getting away with it. Now, roughly nine full years since Ricky Grande and I first met and almost a decade since I started on the mag, a whole lot is changing for me on a personal level but just looking at Ricky’s ‘5 is turning into something of a trip down memory lane for me. It’s funny, back then we went on far more shoots than we do now (yay, budgets!) but I still remember Ricky’s like it was only last month. Fresh faced, definitely thinner and most likely with a really stupid haircut, I went to Ilford in my Bora (back when we could take our own cars on shoots before the accountants here stopped all that!) and met Ricky and his cousin Harm and we instantly clicked. James Lipman was the photographer on the day, a guy who is now without a doubt one of the most in-demand and popular car photographers in the world, and we had such a fun day shooting the two cars, Ricky’s Mk4 and Harm’s Passat, on the streets of Ilford in the sunshine. I’ll never forget us performing a kind of rolling road block on a random overpass to get the rolling shots Lipman wanted, me driving his old Passat and him hanging out the back tailgate like he used to. Health and safety? Yeah, we've totally got that.

    Ricky and I stayed friendly over the years, bumping in to each other at shows and reminiscing about the old days and how much fun the shoot was. He is definitely one of the scene’s nice guys, so it’s pretty cool to be able to write up the feature on this, his really rather cool Mk5 so long after we first met.

    But anyway, that’s enough of the misty-eyed introductions, let’s get down to business. “This has been the biggest build I’ve done since the Mk4 days,” Ricky remembered, “I've had a few things in between, coilovers, wheels and a map, but nothing all that interesting,” he continued. “You see, after the Mk4 I’d sworn to myself that I’d never get that stuck into a car again… famous last words, right?”

    He is right. ‘I won’t get so involved with the next car’ is up there with ‘ah, it all got out of hand’ and ‘I didn’t mean to go so far’ as the most common sentences uttered to us when we interview a feature car owner. Ricky bought the car from the Edition38.com classifieds (remember them? Facebook has got a lot to answer for, they were the place to find a car back in the day) for the simple reason that he hadn’t owned a fifth-gen Golf yet and simply fancied one – simple as that! “I wanted a DSG rather than a manual but the deal on this one was too good to pass up on, I just wanted a simple, fast and reliable new daily really, nothing more than that,” he explained. “I don’t think I’d even got home from picking it up before my brother Naz and some other friends started sending photos and Instagram links of sorted Mk5s to my phone,” he added laughing, “I didn’t really stand a chance, did I?”

    Things started simply enough, like they often do, a good service and going over at GNR Motors, his brother’s garage, was the first port of call. “I’m such a perfectionist when it comes to my cars that I like them to start in the best condition possible, plus doing the boring servicing stuff first saves money in the long run, there’s no point spending all that money doing a car up if it’s going to blow up from something silly later down the line,” he reasoned.

    Service book stamped, next came some coilovers and wheels, a set of Audi Speedlines, which kept our man’s modifying itch satisfied for a little while. A season of shows later, including a few trips to Europe and most notably Worthersee, was the catalyst for the next stage, as it so often is.

    We’ve often said here on PVW that Worthersee is where trends are born. We can’t quite remember which year it was now, our collective memories definitely are more fuzzy than clear cut these days, but we definitely remember when we first started seeing the first of the ‘super low, static, tucked’ cars around the lake. They wore German plates, they were almost all nu-wave cars at the time and while the UK was still loving poke and aggressive fitments, these lads were running tall, relatively narrow wheels tucked right up under widened arches on Mk5 Golfs and the like and most importantly, they were doing it without a compressor or bag in sight. It certainly made an impression on us, and it certainly made an impression on Ricky and his crew too.

    “Our heads were buzzing with ideas on the way home,” Ricky smiled, “and after a few dinners, beers and phone calls back home we had a plan set for the Mk5 to try and get that look we had all fallen in love with out there.”

    The shopping list was impressive; RS4 buckets for the interior, wide wings from SRS like the German boys were running, OZ Ultraleggeras, big brakes on the front and the all-important special super-low coilovers. “Sukh of Westside planted the seed to get the extra low coils on it and he sorted out a set of H&R Ultralow 140s which were fantastic,” he remembered.

    The colour change also came around this time. “Out in Europe we had seen so many brightly coloured cars and just loved the impact they made,” he remembered. “I wasn’t sure what colour to do the Golf but I knew it had to be lairy,” he smiled. “I then saw a Lamborghini Huracan at my friend’s place and fell in love with its bright yellow paint which settled it. It was hard to wrap my head around the car being yellow for a while but it gets noticed where ever it goes which is cool I guess,” he laughed, “you certainly can’t miss it!”

    A little while later and it was time for a change in the chassis department. No, Ricky wasn’t abandoning the static life for a set of Air Lift’s finest, it was more of a sideways move. “My good friend Jason Debono started Gepfeffert UK which is the special super-low KW coilover arm here in the UK,” Ricky explained. “The H&Rs were fantastic but I wanted to support a friend’s new business, and the KWs came with fully adjustable top mounts, trick stainless bodies and adjustable damping too which really sold it for me.” The result of the coilover change? The Golf ended up another centimetre closer to the Tarmac and the Ultraleggeras were shoved even further up in to the arch liners, resulting in a happy Ricky.

    A number of the super-low static cars in Worthersee back then had cages in, purely for the look, and it was a look our man loved. MAQ Racing provided the show cage which also got treated to a wrap of the same yellow as the car itself and the backs of the leather RS4 buckets. Of course, with a show cage and two rear brace bars in place of where the rear bench used to be, something needed doing to the boot itself so in went a false floor setup in matching carpet. Out back Ricky had already put a Gladen 10” subwoofer in a custom enclosure on one side and a pair of Gladen amps on the opposite one courtesy of another friend of his, Amarjit at BladeIce.

    “Then we decided that the rear end didn’t look wide enough so I tracked down a R32 rear bumper and bought a R32-style Milltek system from Ruben at Tuningwerkes to suit it,” Ricky explained. “That, the EVOMS intake, RS4 coilpacks and a stage one map is all it’s got under the bonnet but that’s all it really needs,” he continued. “I’d like to have K04’d it and all that for a big jump in power but being this low does compromise the drivability, of course, and living in London like I do I didn’t think it was worth the extra effort and cost.”

    Speaking of expense, the most costly part of the whole car was without a doubt the brakes. “The brakes, no question, were the hardest and most brain-frying thing we did to it,” Ricky winced, “we must have spent £6k on second hand brake kits Naz and I trying to figure out how to make what we wanted to work, work.” The fronts were simple enough, eight-pot Brembos and 370mm discs but it was the rear end were things were complicated. “We wanted to go with R8 rear brakes with the twin calipers but with larger discs, so the rears are 365mm, only 5mm smaller than the fronts,” he added. “The hard thing was because we didn’t want to run spacers it made getting the ridiculous disks and twin calipers to fit properly a real hassle but we found a way… I’m not telling you our secret though!” He added, smiling.”

    Final items on the hit list were getting the aluminum-look trim across the dash skimmed in carbon fibre, getting the wheel, gear gaitor, arm rest and handbrake trimmed in Alcantara to smarten things up and a final set of wheels, this time 8.5x20” OZ Superturismos robbed, sorry, borrowed from friend Naz.


    So what’s next for Ricky? Well, the Mk5 has already been broken and sold on, its parts living on in numerous other builds while the car itself has gone on to live another life. Ricky himself though, like I was when I was handed this feature to write, has been looking back. “I’ve bought another Mk4 Anniversary Dave,” he smiled, “well, actually we as a group have bought six of them…” Wait, what? “It’s another thing we’ve seen being done in Europe over the years, you’ll see a group of mates all with the same car but in different colours,” he explained. “We already had three Mk4 Anniversarys between us and we’ve all got Mk4s in our blood more than any other car, so we figured if we got three more we would have one each and we could do something like that, all looking kind of the same but different colours, should be cool…”

    Knowing Ricky and his group of mates, they’ll knock the idea out of the park. Get in touch when you have mate…

    “Then we decided that the rear end didn’t look wide enough, so I tracked down a R32 rear bumper and bought a R32-style MiLltek”

    while the UK was loving pokE these lads were running tall, relatively narrow wheels tucked right up under widened arches

    He is definitely one of the scene’s nice guys, so it’s cool to be able to write up the feature on his really rather cool Mk5

    Dub Details
    ENGINE: 2.0 #GTI-AXX-code , #Milltek R32-style de-cat exhaust system, #Evoms-Evolutuion intake, #Revision-D diverter, #Stage-1 map running approx 260bhp, Mk2 Audi TT engine cover, Iridium plugs, RS4 coil packs

    CHASSIS: 8.5x20” #OZ / #OZ-Superturismos LM wheels with 225/30 ZR20 tyres all round, #Gepfeffert-KW-Ultralow 120mm V2 coilovers, chassis notched front, eight-pot #Brembo front calipers with 370mm discs, rears R8 rear brake conversion with double calipers

    EXTERIOR: Wrapped in Satin yellow, SRS wide wings, R32 front Xenons headlights, rear R32 tail lights with upgraded LEDS, Mk6 rear badge, front US-spec front GTI grille, ‘open air’ front vent grilles, R32 rear bumper, rear wiper deleted, boot button popper

    INTERIOR: RS4 front sears with backs wrapped in yellow, MAQ Racing show/roll cage, Gladen 10” sub in custom enclosure, Gladen speaker amp and sub amp enclosure, false floor, carbon fibre dash trims, steering paddles and ashtray, Alcantara steering wheel, arm rest, handbrake lever and MK7 Golf gear knob, Highline instrument cluster and Polar Fiscon, Kenwood DNX521dab headunit, MK6 switches, Candy red hazard button

    SHOUT: Massive thanks to my brother Naz and the rest of the team at GNR Motors, without these guys it wouldn’t have happened and I’d probably have a lot more money in the bank. My Dad and family at Grande Auto Spares for all the support and abuse along the way, Dan and Shaun at Dubcustoms for the wrap, Jason for the Gepfeffert Suspension, Ruben at TuningWerkes for endless hours of support and parts, Amarjit at BladeIce for all the Audio, Mario at MAQ Racing for the cage and brakes support, Sunny at SS Autobody for always being up for a challenge, Edge Automotive, Raz at RetroRaz for all the retro fits, Jay at Splash & Vac for keeping the car clean, Umer at Trade4less tyres, Yusuf at ECP, Ted at TPS, Manny, Leroy, Ash, Slim, Avi B, Anna, Keith, Jamie Tall, Jamie Kebab, Danny Allen, Sukh, Raks, Ranvir, Jas, Harvey, Pandy, Sal, Vick S, Hiten, Gary S, RayARD, KamIce, Fet for the bottomless cups of tea, Vick N at Lowpro, Si at StillStatic, our Belgium crew, Gurj, Dalvir and Jaspal and last but not least all the lads at work
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    PUTTING THE BOOT IN #Volkswagen-Jetta-Mk4-1.9TDI / #Volkswagen-Jetta-1.9TDI / #Volkswagen-Jetta-1.9TDI-Mk4 / #Volkswagen-Jetta / #Volkswagen / #Volkswagen-Bora / #VAG / #Volkswagen / #Volkswagen-Bora-TDI / #VW / #Volkswagen-Bora-IV / #Volkswagen-Bora-1.9TDI / #OZ

    We don’t tend to get too excited over modified Boras these days because we very rarely get the chance, but Anthony Warrior’s example literally stopped us in our tracks. Just look at it! Words: Elliott Roberts. Photos: Si Gray.

    It’s funny, but looking back over the years, we’ve only ever featured a small number of Boras on these hallowed pages – the majority of which have been created across the pond. I’d go so far as to say you could probably count the amount of full-fat, UK-built Boras on one hand. The booted version of the Golf just never really took off here in the UK, largely because people didn’t deem it as sporty as the hatchback or as practical as the estate. Understandably we’re more than a little bit excited to bring you coverage of what Anthony Warrior’s vision of a sporty Bora should look like. It’s more than simply a breath of fresh air… it’s awe-inspiring!

    Despite being very fond of cars from an early age, the engineer from Darlington didn’t pass his driving test until he was 21! “I was certainly a late starter, that’s for sure. I remember as a kid that my dad was always a Ford man, but for me it was hearing my friend’s Mk3 Golf VR6 for the first time. That triggered my passion and love for all things VW almost instantly,” he confessed. Despite initially being into the idea of getting a Golf, due to owning quite a large dog Anthony’s other half, Claire, insisted that it had to be a five-door: “I’m not keen on five-door Golfs to be honest,” said the 35-year-old, “so I started looking at Boras and ended up buying this one.”

    The car might have only had one previous owner and been low mileage with just 50k miles on the clock, but it was totally bone stock and that just wouldn’t do. “Okay, I can honestly say that all I ever really planned originally was a set of wheels and perhaps a remap. Now, some 12-years, five sets of wheels, three sets of coilovers, air ride and £1000s spent on bodywork and interior, I can safely say I didn’t intend to go this far.”

    Anthony’s modified journey didn’t begin all that positively though, with a set of 18” Audi A8 replica wheels shod in equally awful balloon tyres being his first step on the ladder. It was actually PVW’s very own Dave Kennedy, or rather his Bora project, that helped Anthony see the light: “I have to say that I’ll always remember watching the progress of Dave’s black car… And those huge wheels he attempted to fit to it.” Needless to say after the rep’s came a set of BBS RCs, followed by a couple of sets of BMW wheels before Anthony finally wound up with his current set-up: “The wheels were something that took ages to get right, especially as they’re 20s, which nobody had really done at the time or certainly hadn’t pulled off,” he said. Anthony claims it was a bit of a gamble buying the genuine Ferrari wheels as it was a big financial outlay, but when they came up for grabs he accepted the challenge. Talk about trial and error, too: “I knew I’d need to run adaptors and the fronts were pretty straight forward being a pair of 25mm items. Out back the adaptors were quite large at 38mm, but that wasn’t a problem until I offered the wheels up before ordering tyres. For some reason one of the wheels poked out a bit more than the other, so I had to take the adaptors to work and have 2mm machined off one of them.” It’s quite a common problem on the Mk4 platform where the axle never sits perfectly in the arch. You don’t actually notice when running standard ride height as there’s lots of clearance in the wheel arches. It’s only when you’re go low and are dealing with millimeter clearance that it becomes apparent.


    Talking of air-ride, after running numerous sets of coilovers over the years Anthony finally decided to bite the bullet and opt for air: “I decided I was sick of bouncing the 130-mile round trip to and from work, so invested in and Air Lift Slam set-up.” Obviously the install has progressed over time, from the original set-up he fitted in his in-law’s freezing garage, to the carbon-clad, hard-lined work of art you see today. “The air tank is still the original item, but now wears a carbon-fibre skin with copper strands running through it, which Paul from C6 Carbon said was a must-have to tie-in with my copper hard lines.” Since the initial air install, Anthony has also fitted poly bushes throughout and also added IDf drop plates to allow the amount of camber needed to run 11s out back.

    It’s obvious that Anthony, who is an engineer by trade, is pretty proud of what he’s achieved with the car, especially as he’s carried out virtually all of the work – other than the paint and carbon – himself! Believe it or not the all-metal, wide-body makeover was carried out around six years ago (before the air ride and Ferrari wheels, in fact) when Anthony was still on coils and looking to fit some wide 6-series BMW wheels. “The bodywork had to be one of the most time-consuming parts of the whole project but then it was done twice. I wanted the arch lines to be as close to factory as possible, to keep it subtle.” As if widening the car by around 4” front and rear wasn’t going to be pretty damn obvious. The thing is, despite the added girth and crazy-wide wheels filling each corner, Anthony almost pulled off the whole subtle thing. For some reason though, he wasn’t really happy: “I seemed to fall out of love with the car for a while at this stage and it just got used and abused really.” It was only after talking to his friend, Dentman that Anthony got the bug again: “He suggested I should take the car to Autospray in Darlington, which I did. We discussed my plans and I quickly decided they were the right guys!”


    Apparently the car was only booked in to have the wide-body conversion reworked, which should have taken a week, but that soon changed to include smoothing the doors and rear bumper, repainting the front bumper and bonnet, then doing the B-pillars and rear door quarterlight bars gloss black, plus adding new window rubbers, clips and screws: “Four weeks later it was ready for show season. That was four years ago, and since then it’s been back ever year to have little bits added or improving,” he said. The car has got continuously smoother as time has gone on. However, we love how the gloss black external parts break up the Satin silver colourcoding so it’s not too over powering.

    On the engine front Anthony hasn’t gone too overboard, but he did admit to getting a little fed up being left behind by his mates whenever they went out in their cars together: “I needed to do something, so I took the car to Revo for a remap, but that turned out to more than a simple flash. We actually had to remove the ECU and install a new chip. What a difference it made out on the open road, though.” After a quick rolling road session it showed 152bhp and 270lb/ft of torque: “I was pleased but figured we could do a little better, so went for a full Milltek system from the turbo back, with de-cat pipe, too." With the addition of an ITG panel filter and Allard EGR delete, the final outcome was 165bhp and 297lb/ft and Anthony was finally happy! Having driven the car for best part of a year with the tiny stock brakes hidden behind those monster 20” hoops, Anthony was ready to up his game again, especially now he had a bit of extra power, too: “Even though I’d fitted a 312mm TT set-up up front they still looked small and the standard rears we just embarrassing, so a set of fourpiston Ferrari Brembos were sourced to replace the fronts. Then all I had to find a set of suitably large discs and make them fit,” he smiled.

    After quite some time spent searching, Anthony eventually found a set of 400mm Alcon discs originally intended for a Jaguar XKR: “First these needed redrilling to fit my 5x100 hubs, then the bell housing needed machining down so the wheels would clear them.” And this was before he’d fathomed out how to make the calipers fit: “I started with cardboard templates and using wooden blocks to get the measurements for the adapters right. Then I bought two pretty large bits of steel, which were drilled and milled for around ten hours apiece. I went a bit over the top getting them as smooth and shiny as possible,” he said. Anthony claimed by the time it came to the back he’d run out of ideas, not to mentioned money: “I figured I’d got a perfectly good 312mm set-up going spare now, so why not just convert that to fit the back?” How hard could it be? “Well, after a bit of drilling, cutting, grinding and lots of swearing they went on.”

    Although hard pushed to choose his favourite single modification, Anthony admits that he is particularly fond of the way the interior came together as a whole: “I just love the Recaros up from and am so pleased Paul made me do the Mk3 Rocco rear bench conversion, too. I love all the carbon work Paul’s done inside as well, then there’s the TT dash which tops it all off for me.” That said, the dash swap was probably the hardest part Anthony had to tackle himself: “I thought, how hard can it be?” Turns out, pretty damn hard! “I needed modified clocks because my car’s a diesel and they never made a Mk1 TT diesel, then the steering column had to be lowered and brought backwards,” he continued, “and because I did the full centre-console, the gear linkage had to be modified so I could select all gears. This, along with all the wiring and installation of the electric heater box – as my car didn’t have climate control – made it more than a challenge.” It was worth it in the end, especially with the diamond-stitched leather top, tying it all in nicely with the rest of the trim.

    We asked Anthony what he’d change about the car if anything and he had this answer: “I wouldn’t really change a thing other than just doing it the right way the first time around, rather than rushing in and regretting it after.” As for the future, he’s going to look at cleaning the bay up, tucking some wiring and adding some more carbon: “Of course more carbon, lots and lots of it!”


    Dub Details

    ENGINE: 1.9-litre PD 115 TDI with custom chip (producing165hp and 297lb/ft), 3” down pipe and de-cat, #Milltek non-resonated system with twin-exit back box. Allard EGR delete pipe, #ITG panel filter, Touran engine cover painted crackle black, #Forge short shift kit

    CHASSIS: 8.5x20” and 11x20” Ferrari 599 HGTE three-piece forged wheels by OZ with polished lips and faces mounted on G23 adapters (25mm front, 38mm and 36mm rear) with 215/30 and 245/30 Nankang tyres respectively. #Air-Lift-Slam-Series front struts, #Air-Lift tapered rear bags, #Air-Lift-V2 management, #Viair-444cc compressor and five-gallon tank, #Powerflex poly bushed all round, IDF rear correction plates. Ferrari four-pot front callipers with custom machined brackets and 400mm Jaguar XKR Alcon discs re-drilled to 5x100 with machined-down bell housings, Audi TT 312mm front brake set up adapted to fit the rear with callipers painted yellow to match fronts

    EXTERIOR: Full respray in the original Volkswagen Satin silver, arches extended 40mm each side in metal, smoothed factory bumpers blended in the extended arches (front and rear), smoothed rub strips, side repeaters and roof aerial deleted, genuine Golf Anniversary front valance modified to fit and painted gloss black, genuine Golf Anniversary side skirts, Bora 4Motion rear valance (painted gloss black), genuine OEM xenon headlights with twin, centre running lights and turn signal relocation, all-red rear lights with gloss black housings, Lupo stubby mirrors (electric and heated) with clear glass and gloss black basis, new window rubbers all round, gloss black B-pillar and rear door window bar, gloss black grille, bumper grilles and scuttle tray, genuine Jetta GLI grille (carbon skinned), aero wiper arms and blades, gloss black rear towing eye cover

    INTERIOR: Full Mk1 Audi TT dashboard and centre console conversion with diamond stitched leather top and custom instrument cluster, modified steering column and shortened gear linkage relocated OB2 port, Climate Control retro-fitted with heater box change, Recaro Sportster CSs in black leather with gloss black inserts, Mk3 Scirocco rear seats retro-fitted and trimmed to match fronts, six-speed Beetle Turbo gear knob, Momo 280mm wheel, carbon-skinned door card tops (with deleted door pins), steering column cowl and TT knee bars (all carbon skinned in Audi small weave by C6carbon). Black perforated leather roof lining and A, B and C pillars, Golf Anniversary black grab handles, interior light, seatbelt tops, sun visors, alarm sensors and rear view mirror, Passat mirror adjuster, leather door cards all round with custom audio builds in front doors. Brushed-aluminium door grabs, custom bootbuild with floating floor (lit by LEDs), five-gallon tank skinned in small-weave carbon with copper strands running in the weave, copper hard line installation, twin AVS polished water traps, polished compressor fittings and polished bulkhead fittings

    AUDIO: JL Audio MBT-RX Bluetooth receiver, #Precision-Power-Par245 five-band EQ mounted where head-unit would have been, JL Audio XD 1000/5v2 amp with copper/carbon-skinned cover to match air tank, JL Audio TW3 12” sub in non-ported custom enclosure, 8 x 6” Jehnert woofer speakers 2 x 4” Jehnert mids, 2 x 2” Jehnert tweeters, Jehnert crossovers and lots of Dynamat throughout

    SHOUT: My wife, Claire for putting up with ‘that car’, Paul at Deluxe Detailing for looking after and preparing the car, Mike and Vicks at Kleen Freaks for all their support, Paul at C6 Carbon for all the carbon goodies, Pete, Adie and the crew at Autospray Darlington, Justin at Car Spa Darlington, D&W Wheel restorers for the powder coating, Rob at JL Audio UK, plus Lee, Woody, Roger, Ricky and lastly my buddies Dentman, Shaun, Begley, Wardizzle, Cuzy and Nathen

    It’s obvious that Anthony is pretty proud of what he’s achieved with the car, especially as he’s carried out virtually all of the work himself.

    I just love the Recaros up from and am so pleased Paul made me do the Mk3 Rocco rear bench conversion, too.

    Recaro CSs are pretty special up from but Scirocco rear bench is a genius addition.
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    GREAT WHITE #Volkswagen-Corrado-G60 / #Volkswagen-Corrado / #Volkswagen / #VW-Corrado-G60 / #VW-Corrado / #VW / #2017 / #1992 / #Autostrada / #Volkswagen-Corrado-Supercharged / #Volkswagen-Corrado-G60-Supercharged

    Modified Corrados are hard to come by at the best of times and tastefully tuned ones even more so. Thankfully, Declan Bowyer’s G60 is a good egg! Words & Photos: Jon Cass

    It was only around five or six years back that VW’s striking Corrado seemed to be making a major comeback with an array of modified examples suddenly breaking on to the show scene. There was much whooping and high-fiving from Corrado fans all round, yet disappointingly, this trend has slowed down more recently. Thankfully it looks like at least a few are waiting in the wings. The vast number of stunning, fresh VAG builds at 2016’s Elsecar At The Races was truly mind blowing, yet it hadn’t gone unnoticed that there were barely any non-standard Corrados present still. There was one though, and boy did it stand out… as the two trophies from that day will testify.

    Declan Bowyer may only be 27-years-old, but his passion for VW’s timeless coupe stems back to 2007 when he was just 17. “I went to my first Dub meet that year and there was a blue Corrado VR6 running Schmidt Modernlines with Porsche seats. From that moment on I knew this was the car to have,” Declan smiled. Yet, like so many of us, his driving career actually began with a classic Mini. “I learnt a lot from that car in the time I had it, even though it was eventually stripped and never fully rebuilt, “ Declan confesses, “I met my girlfriend, Carly at a VW show soon after and bought a Mk1 Golf GX.” The Mk1 was never going to be a show winner as Declan’s budget was very limited at the time. It was, however, lowered to the max and consequently more was spent replacing sumps than tyres!

    “While I had the Mk1, I started looking around at Corrados, but I was still only 19 at the time,” Declan remembers. “I noticed new ones pop up on eBay and this white, ’92 G60 appeared for sale only two hours away from me, so I went over to have a look.” When a vendor is genuinely into his cars, especially the model you’re buying, that’s always a good sign and fortunately this was the case here. “He had other interesting projects on the go including a Mk1 Caddy with a V6 Audi lump in the back. Thankfully the Corrado seemed genuine, so I went for it.” Apparently it was also completely standard, still wearing its factory BBS RZs, complete with matching spare wheel and cloth seats, though this wasn’t in the best condition and the bodywork had began to show signs of rust; “I didn’t think it needed much work despite this, but I’m sure as anyone else with a G60 Corrado will know that they can soon turn into a money pit,” Declan laughs.

    Initially things went well and Declan drove his new purchase around for around two years with no serious problems; “I didn’t plan on heavily modifying the car to start with,” Declan explains, “I just added a set of coilovers, a new exhaust and painted the wheels.” The Corrado was even driven to the Nurburgring where it performed pretty well, but shortly after things started to go wrong. “The head gasket let go on a trip back from Cornwall, but at least this gave me the excuse to remove the head and opt for a Stage 2 upgrade with gas-flowed, ported and polished head,” Declan smiles.

    Attention then turned to the worn cloth interior, which would arguably have been a little downmarket even when the car was new. Luckily Declan’s partner, Carly had decided to remove some of the mods from her Lupo before putting it up for sale and amongst these were a pair of Porsche 964 half-leather seats, which really suit the Corrado. Declan managed to source a set of leather door cards, a rear bench and also added a black carpet with fresh Alcantara headlining to match. “Soon, after all the interior had been completed, I was driving along and suddenly the front subframe snapped,” Declan recalls, “I had to buy a new subframe, which I strengthened, but there had been a lot of suspension damage caused, too, so I bought a set of KW Variant 1 coilovers, a poly bush kit and wishbones. I then had everything powder coated and sealed to eliminate anything like this happening again.”

    By now a pattern was emerging where modifications had escalated following disasters and more were yet to come. There was a brief reprieve before disaster number three struck, however, enough to give Declan time to sort the deteriorating bodywork. “I was still driving the Corrado on a daily basis and this was having an adverse effect on the paintwork,” Declan recalls, “rust was starting to appear in a few places and I needed to get it sorted before it got too bad.”

    Luckily Declan had a friend that worked at Lexus who was offering to carry out a full respray. All Declan needed was to strip the car first to save time in the paint shop. “I remember it was winter time and I had to drive the car there in the snow with no windows in, which was certainly an experience,” Declan laughs. “I wanted to keep it the original Alpine white as at the time I had no intentions of spraying the engine bay.” The end result was flawless, but this also meant the Corrado was now too nice to remain a daily driver.

    As 2012 came around it marked a return to the now familiar disaster zone when the G60 engine packed up whilst returning from Nottingham; “We’d just bought our first Royal Python snake (as you do – All) and were on our way home, so we had a few strange looks from the recovery driver as we tried to conceal the snake in a fabric bag,” Declan smiles.

    The failure of the G60 at least meant Declan had an excuse to sort out the engine bay, which was by now letting the side down compared to the rest of the car; “I had to take the engine out anyway, so it was a now or never decision when it came to smoothing the bay itself,” he remembers. This would be the hardest part of the whole build taking loads of time and patience with all of the work carried out by Declan, his family and a few mates in his tiny garage. “I’d not carried out any fabrication work on this scale before, but as I’m a hands-on type of guy, I was ready to give it a go,” Declan tells us. “I’d studied other cars I’d seen at shows along with magazine features which helped a lot, but all the work involved and having to buy parts in from Germany and the USA meant the Corrado was off the road for two years in total.

    Once all the fabrication work was complete, the bay could be sprayed by the highly respected, Tim Ansell at True Paintworks; “When it came back it blew my mind, but I then started panicking about how I was going to put an engine and all its ancillaries back inside without causing any damage,” Declan adds.

    The damage to the original engine was unrepairable, so a second-hand unit was sourced and rebuilt from a bare block, complete with PG Stage 2 gas-flowed and ported head with Bar-Tek hydraulic lifter kit. It also benefits from 550cc injectors and looks the part with that custom G60 cam cover. The supercharger is a Stage 4 Jabba Sport item with 65mm pulley and Declan has also added a BBM induction kit, with a custom intake pipe, angled to exactly 90 degrees along with custom coolant hoses and a Mocal oil cooler. Some serious smoothing has taken place on the manifold and the custom intercooler set up includes a Rallye U-bend, custom hoses and top-fill radiator, while the exhaust system is now a Milltek Classic item with de-cat connected to a four-branch stainless manifold. “I‘m really happy with the result, especially the colour coding, which went just as planned,” Declan smiles. “The only aspect I’d change is the stock ECU (currently running an SNS Pro Digi-lag custom chip), as I could have omitted a lot of sensors and running issues, though these problems have finally been sorted out,” he said.

    With the engine back in, thanks to a cupboard full of bed sheets to protect the bay, Declan then had to reroute the wiring underneath to retain that cleaned look. The ECU is now inside the cabin and the battery and washer bottle are located in the boot, while the ignition coil is mounted on the scuttle panel. “I then had to make my own length HT leads to the coil to keep that hidden and ran the vacuum hose for the ECU through to the inside of the car,” Declan points out, “I could then get rid of the coolant expansion bottle thanks to the top fill radiator I’d made.”

    You can understand by Declan’s detailed explanation why the whole engine bay process took two years. In fact, given the amount of thought and money that’s gone into it all, we’re surprised it didn’t take him longer!

    The final puzzle to solve was now the wheels… the make or break point of any modified car. “I knew which wheels I wanted all along; a set of dark grey, 16” Autostrada Monzas and it had taken four years to find some,” Declan recalls. “The dishes were refurbed by Ellie at Voodoo Motorsport and Slam Signs managed to reproduce the original logo in gold leaf to make them perfect. I couldn’t wait to get them on, but as ever this didn’t go to plan,” Declan recalls. “I had already upgraded the brakes to Ibiza Cupra R Brembo callipers and discs and had been advised these wheels would just bolt straight up to them. They did on the rear over my Mk4 brake conversion, but not on the front so I had to shave 10mm from the calliper carriers, which did the trick!” The result is tight, but it works perfectly and stops on a penny according to Declan.

    Seven years of hard graft and a last minute fitment of an OMP steering wheel eventually saw the Corrado make a return to the road where it soon picked up a healthy stack of trophies, a reward for Declan’s efforts. “I’m really proud at what I’ve achieved along with some help along the way and what seemed like an endless string of disasters has resulted in a positive outcome,” Declan smiles. The Corrado may often be overlooked these days, but when you see creations like this spring out of the woodwork, it’s sometimes hard to work out why.
    Porsche 964 seats always look at home in a 'Rado, don't they? Royal Python snakes (just out of shot), not so much...

    "I’m sure as anyone else with a G60 Corrado will know that they can soon turn into a money pit”

    "I had to take the engine out, so it was A now or never decision when it came to smoothing the bay"

    Dub Details #Volkswagen

    ENGINE: 1.8-litre four-cylinder G60 in smoothed engine bay with Stage 2 head, #Stage-4-supercharger with Rallye U-bend – painted in Toyota Demeca grey. #BBM fuel rail, pressure regulator, 550cc injectors, custom coolant pipes, custom intercooler set-up, BBM modified induction kit, smoothed inlet manifold – painted in Toyota Demeca grey, #Supersprint four-branch stainless exhaust manifold, #Milltek exhaust system with decat. Expansion tank deleted, battery relocation to boot, washer relocation to boot, custom wire tuck, #SNS 5.5 Digi-Lag ECU chip, custom silicone induction hoses, custom top-fill radiator, custom G60 cam cover, braided fuel lines, braided oil cooler lines, Mocal oil cooler with thermostat, MSD Blaster coil with Magnacor HT leads, Stage 2 carbon Kevlar clutch kit, #Walbro 226 fuel pump

    CHASSIS: 7x16” (front) and 8.5x16” (rear) ” #Autostrada-Monza wheels painted metallic grey with polished lips and black barrels with Nankang NS2 tyres and 30mm 4x100 to 5x114.3 custom adapters. #KW-Variant-1 coilovers, poly-bushed front subframe, poly-bushed steering rack, poly-bushed wishbones, Mk4 Golf top suspension mounts, #Eibach anti-roll bars with poly-bushed mounts, Ibiza Cupra R Brembo front callipers (modified), 305mm drilled and grooved front and rear discs, Mintex front brake pads, custom front braided brake hoses, Mk4 Golf alloy rear callipers, #EBC Ultimax rear brake pads, custom braided brake lines, Porsche 944 brake fluid reservoir

    EXTERIOR: Full respray in VW Alpine white, side strips deleted, badgeless grille, tinted headlights, carbon number plate light plate, 50mm front VR6 splitter, rear wiper deleted

    INTERIOR: Porsche 964 half-leather Alcantara front seats, Corrado black leather rear bench and door cards, OMP 330mm steering wheel, black Alcantara roof and sunroof lining, black VR6 sun visors, leather handbrake lever

    SHOUT: This has been a family and friends build and I couldn’t have done it without them. Huge thanks to Tom Justice, my brother Sean Bowyer, my mum and dad, Les Bowyer and Barbara Bowyer, my friend Joe Whitmore who apparently helped in some way, my fiancée Carly Dolman, Tim Ansell at True Paintworks and my friend Paul Cross, Ellie at Voodoo Motorsport and everyone who has supported me along the way, plus Chris Perry for helping to find the photo shoot location
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    DARWIN AWARDS


    Bernd Stich’s Jetta could roll its way to the top of the podium at any show-and-shine you care to mention. But this is no cynically thrown-together show pony – this is the culmination of over twenty years of evolution… Words: Daniel Bevis. Photos: Igor Vucinic.

    Evolution has a lot to answer for. Lots of your body parts serve no useful function – body hair is pointless for modern human living, for example. And wisdom teeth do little other than to misalign jaws, while the auricular muscles around your ears are unnecessary as we don’t swivel our ears to hear sound like some creatures do, and your coccyx has no purpose because you don’t have a tail. Your appendix is rubbish too – when people largely ate plants it might have had some role in digestion, but nowadays the only thing it can do is get inflamed and explode, which doesn’t help at all.

    Nevertheless, evolution is super-clever. Just look at the quirky national characteristics of speech patterns – the Spanish are loud and boisterous, the Italians lyrical, the French romantic, and acoustic adaptation theory suggests that such traits develop so that the sounds we make work best with our natural surroundings: harsh consonants get lost or distorted in rainforests, but have room to breathe among European hills and valleys. Open syllables like ‘aloha’ work better in tropical climes. And so it goes. It’s not just humans, this is true of birds and cats and all sorts.

    In modern Germany, evolution is evidently working overtime. This beige Jetta proves it. In the time that Bernd Stich has owned his trusty coupe it’s passed through more radical evolutionary changes than a millennium of walking sea creatures, each phase markedly different to that that preceded it. It’s as if Bernd and his VW are syncing DNA code to determine the ultimate fate of this well-beloved car. Well, either that or he just really likes it and happens to change his mind a lot. “I can tell you the exact date I bought the car – 22nd November 1996,” he tells us. “And how it looks now - this is what I call my Level 5 modifying…”

    The love affair, which has clearly endured, began early; Bernd was desperate to get his hands on the Polar silver car in time for his 18th birthday, and it’s been through a multitude of looks and setups since then, with each year bringing fresh enthusiasms. The whole merry-go-round was spun into action when he swapped out the original 1.3-litre motor for a rather more robust 16v, and it was the act of gradually but irreversibly becoming a regular show-goer that cemented his keenness for modifying in general and the #VW scene in particular. At the time people weren’t really modding Jettas, it was all about the Golf, so that immediately gave Bernd the edge, and with the ‘valver’ in place he opted to augment it with a set of G60 front brakes and GTI 16v rears – and it was at this point that the aesthetic evolution went into overdrive. Before it knew what had hit it, the ’89 Jetta was wearing big bumpers and slathered all over in pearlescent orange Volvo paint, the smoothed bonnet and boot lid complemented by an absence of arch trims between those fat bumpers. And then the interior was trimmed in cream leather, some Porsche 944 wheels appeared, there was talk of air-ride… the car made it into these very pages, in fact, such was the radical nature of it all.

    Bernd wasn’t done yet, though because not long after the 2.8-litre VR6 motor appeared. It’s just a natural function of the survival-of-the-fittest ethos, is it not? Bigger is often better.

    Forget ‘less is more’, increasing your piston count by 50% is where it’s at. So in 2003, Bernd got hold of an Mk3 Golf VR6 and basically tore it to pieces, harvesting everything he might need to pump up his Jetta’s creds. The engine is naturally the first thing you’d spot from this major round of surgery, artfully tarted-up as it is by oodles of chrome work and a smoothed bay for it to snuggle down in, but the eagle-eyed will also have spotted the Mk3’s dash, which has been fettled and honed to fit perfectly inside the cabin. Some oh-so-early-’00s König seats found their way in, too, along with a polished Wiechers roll cage and a beefy audio install. Oh yes, the exterior wasn’t a lurid orange any more either – it was something far more OEM-subtle from somewhere within the silver/blue/grey Venn diagram. Air-ride was taken care of by a simple #BSS single-pump system with a five-gallon tank and much of the wiring hidden away.

    “Lots of the ancillaries were chrome-plated before refitting,” Bernd explains. “The slam panel, driveshafts, wishbones, gearbox end casing, front sub frame, brake servo…” It starts to turn into a very long list. Even the Typhoon induction kit is shiny enough to hold a mirror up to the fact that you don’t own a Jetta this cool. It was once all of this work was done that Bernd decided to strip the thing down to a bare shell again and paint it all in VW Passat Grey Pearl. That was back in 2006. And if we fast-forward to 2013, we find it all being stripped down once more. That’s the crux of natural selection, it favours adaptability.

    There are two key elements that immediately grab the eye as a result of this latest, fastidiously executed evolution. The first is the colour: now swathed in Nevada beige, the Jetta flies deliciously under the radar to all but those in the know, having the air of an OAP-spec budget runabout that’s secretly pumped full of steroids. The second is what Bernd’s been up to underneath the car. This is the kind of detail that’d only become apparent to you if you were on your hands and knees, greeting the car in the manner in which a dog might romance another (unless, obviously, you’re looking at photos of it in a magazine – which, mercifully, you are), but the level of work that’s gone into it is really quite phenomenal. The entire underside has been stripped, perfected, and polished to an improbable shine, a festival of beige that culminates in a mouth-watering fuel tank (there’s a phrase you don’t hear very often) that’s wrapped in sumptuous leather and held in place with polished straps – a gift from buddy Ralf K, who used to own the very tank fitted to his Golf.

    This is very much the pinnacle of the modifiers’ art. None of this stuff needs to be done. The fact that it has been done, and done so well, demonstrates Bernd’s commitment to doing things properly. Those shows he used to go to in the nineties clearly left quite an impression.

    Beyond the paint, much has been done to ‘retro up’ the look: those big bumpers are long gone, replaced by the period skinny items that work so well to amp up the element of stealth, and the nerds among you may have spotted the 1986-spec doors, chosen for their old-school quarter-light windows. And the interior is now a fabulous showcase of what might have happened back in the late-1980s if a tuner like Radford or Tickford had offered a coach-built version of the Jetta – it all oozes with custom vintage flair, and yet the materials are distinctly premium and high-end. Porsche 924 seats wear bespoke faux-leather and corduroy, the rear seats trimmed to match and with a colour-keyed carpet to suit, and the pillars are trimmed in a tasteful brown to dovetail with the dash. There’s no stereo any more as today Bernd simply prefers the aggressive bark of that VR6 through its shiny Supersport system.

    “It was my first car,” he grins. “All the others are just dailies… it started off all original and cost me DM7500 back in ’96. And now – plans for the future? No, I have none for this car. The baby is coming in May, the next Jetta driver, that’s my future.” Sure, he says that, but it’s not really his decision to make is it? This Jetta has held Bernd in its thrall for over two decades, its very physical construct controlled by the whims of nature and evolution, and we can’t see this pattern breaking any time soon. For now, this car exists as a perfect showcase of age-old passion and flawless craftsmanship. What happens next is in the hands of anagenesis and biodiversity.

    Dub Details #Air-ride / #1989 / #Volkswagen-Jetta / #Volkswagen / #VW-Jetta / #Volkswagen-Jetta-II / #Volkswagen-Jetta-VR6-II / #Volkswagen-Jetta-VR6 / #Volkswagen-Jetta-Air-Ride / #Volkswagen-Jetta-Air-Ride-II / #VW /

    ENGINE: Chromed and detailed 2.8-litre VR6 ( #AAA ), with #SuperSport stainless steel exhaust system, Typhoon induction, Mk3 Golf VR6 manual gearbox – lacquered gloss black

    CHASSIS: 7.5x17” BMW #BBS split-rims with 195/35 Nankang tyres. #GAS ( #German-Air-ride-Systems ) air-ride setup, Mk2 VW-Golf G60 front brakes with 280mm discs, Mk2 Golf GTI rear axle with disc brakes, braided lines

    EXTERIOR: 1989 shell painted Nevada beige, 1986-spec doors, small bumpers, shaved bay, detailed underside, leather-trimmed fuel tank with polished straps

    INTERIOR: Mk3 Golf dash, Porsche 924 front seats – custom-trimmed in faux-leather and corduroy with rears to match, Raid wooden steering wheel, Beetle shifter, beige and brown #Vorwerk carpet, chrome air tank in boot

    SHOUT: My best friends Björn, Timo, Maik, plus Ernst-Equipment (tuning parts), Febi (aftermarket parts) and Carlack-Schwung (painter)

    The whole merry-go-round was spun into action when he swapped out the original 1.3-litre motor for a rather more robust 16v.

    Polished #VR6 lump lives in engine bay so clean you could, well, lick it!

    Single air tank fixed to back of rear bench means boot is left clear.

    Since we last saw the car Bernd has gone balls-out with the underside. Note the leather-clad fuel tank.
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    TOP BANANA 1.8T-powered euro-look mk3

    / #VW-Golf-III / #VW-Golf-Mk3 / #VW-Golf-Mk-III / #Volkswagen-Golf-Mk3 / #Volkswagen-Golf-III / #Volkswagen / #Volkswagen-Golf-1.8T-Mk3 / #Volkswagen-Golf-1.8T-III / #Volkswagen / #VW-Golf-1.8T-Mk-III / #VW-Golf-1.8T / #VW-Golf-1.8T-Mk3 / #VW / #Volkswagen-Golf-Bi-Turbo / #Volkswagen-Golf / #Volkswagen-Golf-Bi-Turbo-Mk3

    Big-turbo Mk3 runs US-spec bumpers, air-ride, full cage and stripped interior. Words: Daniel Bevis Pics: Patrick Hille For Mitch van Werven, the act of building his dream car has been a life-altering journey of friendship and inspiration. And not just life-altering – this unmissably yellow GTI has some mind-altering properties too…

    If we’re to believe the late- 1960s Donovan song Mellow Yellow, it’s possible to get high on bananadine. This is, of course, nonsense – you can no more experience a psychotropic buzz with a banana than you can brush your teeth with it or use it to hammer an IKEA wardrobe together.

    A hoax recipe for bananadine was published in the Berkeley Barb, an underground counterculture newsletter in California, in 1967; it detailed how it was possible to extract a psychoactive substance from banana skins, which you could then smoke to achieve LSDlike effects. This gained some credence when William Powell, who thought it was true, reproduced it in The Anarchist Cookbook in 1970. In fact, the original feature in the Barb was a satirical piece questioning the ethics of criminalising psychoactive drugs; smoking banana skins may create a placebo high at best, but there’s no scientific reason why you could actually get stoned on bananas. You can’t.

    That said, there must be some manner of mind-altering substance swirling around the city of Lochem that’s enabled the coming-to-life of this trippy little Golf. Lochem’s in the Netherlands, and we’ll leave you to draw your own conclusions there; suffice to say that this is one Mk3 Golf that dabbles in the more colourful fringes of our everyday perceptions of reality.

    Still, we’d never suggest that this car’s owner, Mitch van Werven, was under the influence of anything beyond strong coffee and a pocketful of dreams throughout the Golf’s reinvention; indeed, the evidence seems to suggest that he’s singularly focused on automotive mischief rather than anything chemical. “Why spend so much time, money and energy on a car?” he grins. “Because we can, and we enjoy it very much. Some people go to the club, we go to the garage and build our dream cars.”

    Stirring sentiments indeed, and the inclusive ‘we’ here refers to a disparate but close cast of characters who feature strongly in Mitch’s own everyday interpretation of garage life; Bernd, Joran, Stevie, Roberto, Thomas, Mike, Martijn, these are the personalities who’ve helped our protagonist mould and shape his vision from questionable base to yellow dream machine. “I bought this car when I was sixteen, back in 2009,” Mitch explains. “Back then I was working at a garage and this Golf arrived in part-exchange – a #1996 GTI 16v. I saw it, and immediately called my dad to say ‘I want this car!’ It had been really well used – 266,000 kms on the clock and plenty of rust, but I think the Mk3 is the best model of Golf. The original Dusty Mauve paint was bad, too, but it was an all-original, three-door GTI 16v, so I just had to have it.”

    As tales of first cars go, it’s not a bad one – so often it’s the case that the best first car in people’s minds is ‘any car – literally any car’, but Mitch is clearly a man of principle and ambition. “The car owns me, not the other way around,” he laughs. “It’s taken years to get it to this point, and it’s not finished – project cars never are, are they? And having started the transformation back in 2010, it’s come a long way.” He’s not kidding. You’d certainly never look at the car and think ‘high-mileage rust bucket’ these days. What about that colour, then? Swapping purple for yellow is a proper Art Attack move. “Yeah, I’m not telling you what the paint code is,” Mitch smirks. “I wanted to have a colour that you don't see very often. Most cars nowadays seem to be blue, grey or black, so I chose a bright shade. Also, I just like yellow…”

    Naturally there was quite a lot of work involved in shuffling the various skeletons in the Golf’s closet before it was ready for paint. The first job on commencing the project was to totally strip the car down to see what was what, then stalk through the thing with lethal force, like some kind of enraged sniper, mercilessly eradicating corrosion and letting in new metal to cover the tracks. While this was going on, Mitch and his crew also removed everything superfluous from the car, following an over-arching ideal of exploiting power-to-weight ratios once the thing was completed. The Mk3 Golf is by no means a lard arse, but there are always savings to be made. A gram here, a gram there, it makes a difference. And we’re not just talking about the bananadine here.

    “I made the choice of which engine I wanted, and once I’d settled on the 20vT I went out looking for one,” Mitch recalls. “With some happiness I found another Mk3 that had already been 20VT-swapped, so I bought that as a donor, stripping it completely and selling everything I didn’t need.” The finished product in that shiny bay wears a Garrett GT28 turbo along with some fairly racy manifolds and a #Kdata #kdFi ECU to keep everything humming. And with the shell prepped and the engine spec’d, that sunglass-baiting paint shade entered the fray. “After the car came back from the paint shop, the fun could really start,” he says. “First we built the engine in the car and made it all work, then took it back out again to clean everything – and let me tell you that was a lot of work! The cleaning alone took over three-hundred hours.” And when he says ‘cleaning’, we’re not talking about a duster and a can of Pledge here – take a look at the fastidiously shaved, smoothed and slippery engine bay.
    You could challenge a passerby to wedge a toothpick in there and they’d be confounded for hours. You could drop a handful of toothpicks over the motor and every single one of them would make it down to the garage floor.

    “Together with my best friend Bernd, we put the car back together,” Mitch continues. “We drove across the whole country for parts; this was almost the best part of build, being with my bro, having fun and getting new stuff for the Golf. After we had collected everything we needed, we started really putting the car together and piece-by-piece it blossomed. Every step brought us closer to the final result, and after years of hard work we could finally do some shows. Last year was the best year for us – the car got a ‘Best in Show’, the offer of a PVW feature and a place on display at the Essen Motor Show. This was the point when we said to each other, ‘Yay, we did it’!”

    From the genesis of the idea right to the very end, Mitch’s buddies were deeply ingrained in the process, and it’s this communal all-in-it-togetherness that made the build so memorable. Not that there is an ‘end’ of course, not really – he’s already talking about air-ride, new seats, another yellow repaint, and some serious engine mods too.

    “I can’t honestly say I had a clear idea in my head of how this would turn out, back when I was sixteen,” he admits. “Sure, I had a lot of ideas, but I never thought I’d achieve this unique look.” Indeed, the project today sports a variety of disparate styling cues from across the scene; our American cousins lent some inspiration in the form of their bumpers and wings, while the Jetta nose is a nod to the old-school stables that are mirrored in the choice of BBS RS rims.

    The fact that it sits this low on coilovers rather than ’bags assures credibility and bravado points, and the interior really is something else: that Wiechers ’cage in particular is a shimmering manifestation of the scaffolders’ art, brutally complex and frighteningly purposeful.

    “I was influenced a lot by other Mk3s on the internet, but also just by mine and Bernd’s keenness to try out our own ideas,” says Mitch. “I guess I’d describe it as OEM+ with a race-car influence, but it’s its own thing, really. And the reactions it gets now are crazy; I like to take it out for a drive with my girlfriend over some nice roads, and the feeling of doing that in your dream car is cool, but then when you arrive at a show and people are coming over and saying they love the car – it’s the best feeling. I can honestly say that building this Golf was the best time of my life.” And we can tell by the sparkle in his eye that this isn’t just the bananas talking – this guy’s tripping off his little box on Wolfsburg dreams, and that kind of thing is thoroughly addictive.

    With bright yellow paint, side markers and shiny BBS, Mitch's Mk3 has more than a hint of the US scene.

    Left: Look closer at the weave and you realise this is indeed the real deal. Below: With 742bhp on tap no wonder Andreas is happy!

    HKS Turbo Timer times the turbo and ensures all turbo related things are kept in time. Like the speaking clock.

    Hardcore Wiechers Sport roll cage is not messing about is it?

    Dub Details / #Garrett / #BBS-RS / #BBS /

    ENGINE: #Rebuilt-1.8T 20v with #Garrett-GT28 turbo, rear-mounted exhaust manifold with 3” downpipe, H-profile conrods, kdFi V3 ECU, #Ross-Machine-Racing intake manifold, battery relocated to rear, six-speed manual

    CHASSIS: 17” #BBS-RS-320 (front) and 17” #BBS-RS-350 (rear) with 185/35 Nankang NS-2 tyres. #Weitec-Hicon-TX-Plus coilovers and Audi S3 312mm front brakes

    EXTERIOR: Secret yellow paintwork, US bumpers and wings, Jetta front conversion, ‘cleaned’ boot, smoked tails, shaved bay

    INTERIOR: Stripped and painted, custom Wiechers Sport roll cage, Cobra Monaco Pro seats, Schroth harnesses, #HKS turbo timer

    SHOUT: Bernd Nijdam, Joran Meijerink, Stevie van der Vaart, Roberto Polo, Thomas Kevelham, Mike Temminck, Martijn Maat – thanks to these guys, without them the car would never be completed


    “I guess I’d describe it as OEM+ with a race-car influence, but it’s its own thing, really. And the reactions it gets now are crazy"

    “Most people assume it’s a 3M wrap so it’s always good fun to invite them to take a closer look…”
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    NEW JACK HUSTLER
    A lot of people talk about thinking outside the box when it comes to building a car, but few actually do. Jack Smith is someone who definitely walks the walk though.

    / #Volkswagen-Golf-Mk1 / #Volkswagen-Golf-1 / #Volkswagen-Golf-I / #Volkswagen / #Volkswagen-Golf / #VW-Golf / #VW-Golf-I / #VW / #Volkswagen / #Volkswagen-Rabbit / #Volkswagen-Rabbit-I / VW / #VW-Golf / #VW-Rabbit / #Tarmac / #Volkswagen-Golf-US-Spec-Mk1

    “As soon as the old stock colour started coming up all my ideas about painting it Silver went out of the window”

    “It would have been so much easier to import a full car myself, but with the money I already loaded into the car I thought I’d just build one”
    “It’s something different and I can say that I built it, there’s a sense of pride in that... it's art to me"

    RUN RABBIT

    Jack Smith’s Mk1 may look like a genuine #US-spec Rabbit… until you notice it’s right-hand-drive. And that’s just the start of the madness…

    A lot of people talk about thinking outside the box when it comes to building a car, but few actually do it. Jack Smith is someone who steps right outside of it... Words: Tony Saggu Photos: Si Gray

    To say Yorkshireman Jack Smith has eclectic tastes in automotive faire would be something of an understatement, with less than a decade on his driver’s license the twenty something Rotherham based paint sprayer has auditioned more style and makes of motors than most. “Me, I love building cars, the make and model or even the style isn’t as important as actually making the thing,” he told us. “It gets my mind working, thinking of things that not many people have done before, you know, taking something bland and making it something amazing." His latest metal massaging makeover takes the shape of a German born, English market, Americanised runabout with a petrol to diesel swap, newfangled technology and old fashioned looks... if you’re looking for predictable, keep walking.

    “I actually started with a Renault 5 1.2 five door before I could drive,” laughed Jack, “My dad bought it for me so I had something to work on. That went matt black on lowering springs with some P slot wheels.” Once the 'L' plates had been discarded French fancies were replaced with a little German flair in the shape of a shiny Red 1.0 Mk3 Polo. The rims and springs added gave the car the right look until Jack introduced the coupe to a spot of unintended custom bodywork, “It ended up in the window of a local computer shop...” we’ll say no more. Sadly the lad’s luck didn’t improve much with the wrecked red Polo’s replacement, “Yeah, I had a white Mk3 1.3 Polo coupe after that, almost identical to the red one but with wider arches on the front,” he recalled. “That had a Corsa go into the side of it.” After the two crumpled coupes Jack tried his luck with a five door, another Polo, another Mk3, and tempting fate another 1.3. Thankfully the blue-hued saloon worked out well and was only given up when Jacks present project came along. “I’ve had a Golf, a Vento and even a bagged Mazda 3 along the way,” he told us, “I currently have a daily Lexus GS300 that is VIP inspired on Weds Kranze LZX and D2 air suspension with a fair bit of camber.”

    Switch hitting Japanese gangster rides aside, Jack admits if he’s honest it’s the Dub life that pushes his buttons. “I think it all started from seeing people I used to ride BMX with buying and modifying them,” he recalled. “I found a German modified VW magazine while I was on holiday in Europe years ago, I couldn't understand anything in it but the cars looked pretty cool and I knew I wanted a piece of that, I started getting PVW after that and as soon as I could drive I bought myself the Polo coupe.” The latest Smith built sensation which you see here began like many makeovers with a chance encounter, “I wasn’t really looking to buy a Mk1,” explained Jack, “I had the blue Polo at the time and was pretty happy with it. My mate Ricky had bought it and done a bit of welding and other stuff so he could sell it on,” he continued. “Then it eventually just came up on a local forum that Ricky was selling it soon and at a good price. I didn’t need another car, but who doesn’t want a nice cheap Mk1? I put the Polo up for sale straight away and got on the phone to Ricky.” At seven hundred quid the antique '83 Golf was a steal, it had plenty of issues in all areas but the Yorkshireman wasn’t daunted. “It was pretty tired looking,” he told us, “and it had the typical MK1 rust problems. The paint was very faded paint and honestly it needed a good general tidy up to make it acceptable.” The car ran though, not too bad either according to Jack, the alternator was a bit dodgy but the car came with coilovers. “I had to take it for a MOT and there with a decent list of problems for me to fix,” he recalled.

    A couple of hundred quid’s worth of parts and a spit and polish would have been the sensible thing to do, the resulting ratty but reasonable ride would have kept most Dub fanatics satisfied and smiling. A steady diet of Max Power, Revs, Fastcar and Redline magazines growing up had put Jack in a different frame of mind though, not to mention a couple of older cousins who had done nothing to take the edge off the custom car craving. “There wasn’t a chance of it staying standard,” laughed Jack, “ Initially I wanted to make it like every other MK1 you see at shows, it was going to be silver on polished BBS RS's, but when I actually started working on the car all that changed.” Job one, after the coilovers had been wound down to the limit and a set of Minilites from the old Polo had been bolted on, was to give the car a good clean and go over with a polishing mop to restore the righteous retro Pragus Blue. “As soon as the old stock colour started coming up all my ideas about painting it Silver went out of the window,” recalled Jack, “The blue is just perfect, it suits the car so well.” The next few months saw the car more often than not in pieces on the Jack’s driveway, the Mk1 was a sweet little motor but it was teaching young senior Smith a valuable if hard lesson... it was old, and old things break down and stop working a lot. “One of the biggest reasons the car looks and drives the way it does now is that basically everything needed to be repaired or replaced,” explained Jack, “if I was going to fix something anyway I thought I may as well make it better.”

    Straightening the generally abused and rust riddled bodywork set the direction of the project and gave the car is final character. “When it came to the look I wanted It was mainly the US cars that got my attention,” revealed Jack, “The American lads were doing really low cars, with half the floors cut out and full of exotic custom suspension work. I knew I'd never go that far as it was out of my skill set, but I knew after looking at their cars that I wanted to make my car look like an American style VW.” The internet had taught our man that when it came to true US spec, there was only one direction he could go.

    “The Westmoreland Rabbit,” he smiled, “Once I started thinking about it I realised I’d never seen a US spec Rabbit over here. Everyone was making MK2/3/4/5s US spec, but I couldn't understand why no one had imported or made a Mk1 over here. It would have been so much easier to import a full car myself, but with the money I already loaded into the car I thought I’d just build one.” It wasn’t long before Jack realized that giving his German built hatch the American look was going to take more than just slapping a Rabbit badge on the boot. The American built Mk1s have a look all of their own with more than a few US only exterior details and body panels. “Getting the parts was no joke,” lamented Jack, “A lot of the bits like the Hella rear lights, turn signals, side markers and the grill I got from Mexico via dodgy websites and ebay. The front panel was found on VWvortex after months messaging people who were breaking cars for parts,” he continued. “It a big piece to post over so convincing someone to do it took a while, finally someone decided to do it for me. I can’t remember his name but the bloke was a legend. He only charged me about $60 then $60 shipping as I only got the top half of the front panel to save on shipping costs.”

    The all important and decidedly unique Hella Projector headlights were apparently liberated from some sort of Jeep and sourced through the Edition38 forums for a reasonable £90. “The front wings were a major headache,” recalled Jack. “The driver’s side came from #VW-Heritage over here and only cost £30 delivered, it was a brand new genuine wing. I couldn't believe my luck when I found that.” The passenger side 'fender' however wouldn’t be such an easy acquisition, “The other side I was really struggling,” he explained, “Everyone wanted $500 for shipping and I couldn't justify spending that much for one wing. It took a lot of hunting but after talking to someone on #VW-Vortex from a place called Old-Skool-VW we worked out a way to get around the postage.” Clued up VW heads will already know that the major difference between the German wing and the Pennsylvania panel is the leading edge around the US spec corner light. “He agreed to cut me a spare wing up and sent me only the front part which wraps around the turn signal,” revealed Jack. “He cut it just big enough to fit in a USPS Fixed Rate shipping box. I think this was also $60 plus $45 shipping. Once it arrived I had to figure out how I was going to graft it into a Euro wing.” A good deal of careful measuring, delicate cutting and skillful welding had the wing looking every part the perfect stock American example. While the welder was out the rear panel needed to be similarly cut and shut to house the long rear lights the Yanks like so much. Unsurprisingly Smith has strapped on a pair of Westmoreland issued bumpers fore and aft to complete his American auto adventure, the heavy girder style steel protrusions are normally the first US styling faux par to be binned by Stateside Dubbers, in favour of the slim and sexy Euro examples.

    Toned down with matt black paint and pushed closer to the body with custom crafted brackets however, it seems Jack has made VW of North America’s design department’s bumper blunder a thing of stylish beauty. It’s no surprise, with our man being a painter by trade, that the reapplied Pragus Blue top coat is smooth, silky and to our eyes perfectly refinished, Jack though, ever the perfectionist, reckons he could have done better. “I’d like to go back and redo the bodywork,” he told us, “Since I've gained more experience in the trade over the years, I've got more of a eye for detail now than when I first painted it, I was only in an apprenticeship back then.”

    Jack told us the original 1.1 under the bonnet was on its last legs, pumping out more oil than horsepower. “I got offered a 1.8 conversion and tried fitting that, but it would never run and no one could figure out why it wouldn't start,” he told us, “I got so annoyed and decided just to rip it all out and find a cheap engine to chuck into it. I saw a 1.6 #GTD for sale for £150, it had everything including the fuel pump and turbo.” Jack admits his experience with engine conversions is pretty limited, but dropping in the diesel was a doddle, “essentially its four mounts, a custom downpipe and about six wires,” he enthused. “Obviously there's a little more to it than that, I had to get a gearbox and some other stuff, but me and my mate Kyle could take it out in less than two hours.” Although originally the cheap oil burner was just supposed to be a temporary engine to get the car mobile, Jack told us it wasn’t long before the diesel started to grow on him, “I soon fell in love with it,” he smiled, “ turning the fuel and boost up made it really nippy and it was still stupidly economical.

    The kinda reason I decided to keep it and refine it,” he continued, “I took it out a couple of years ago to clean it up and smooth the engine bay. It still makes me smile when you look in the rear view mirror and see a cloud of black smoke.”

    Despite the nicely detailed diesel swap and skillfully executed body conversion, Jack reckons his favorite part of the build lays elsewhere, “It’s without a doubt the wheels,” he smiled proudly, “The Fifteen52 Tarmac348 wheels, I wanted them the day they got released but I couldn't afford them.” A good deal of overtime and skipping a few nights out with the lads, as well as selling his Fifteen52 Snowflakes had the prized rollers bought though, to up the ante a touch the boys at the legendary California style haus custom made the rims in two piece with brushed centres and polished lips for the Mk1.“The suspension is a Havair strut kit with paddle valve management,” continued Jack, “I think they were the only MK1 struts available at the time when I was wanting to get air for the car. To be fair I've had them a fair few years and it’s all still working fine, which is not bad seeing I used to use this car daily as well.”

    Raising the turrets and giving the frame a little notching love helps the bags put the little Mk1 in the weeds, “The wishbone mounts and sump sit on the ground now,” he assured us. “The front struts have been drilled out to give me more negative camber and the rear suspension has some camber disks behind the stub axle to do the same at the back.” The dropped and diesel swapped hatch from oop north is certainly unique, not just in the land of dales and moors either, Jack’s built himself something very different from a familiar platform and we reckon you would be hard pressed to find a twin on either side of the Atlantic ,” he smiled, “Its art to me, creating something special out of something ordinary.” We think he nailed it.

    1.6-litre Mk2 Golf GTD lump provides plenty of smiles with the 'boost and fueling would up." Looks sweet too!

    Air install out back is simple but clean and nicely functional. Well, what more do you need really?

    "Heeeeres Jacky!" Jack's plan to chop Si Gray up with an axe thankfully didn’t pan out. All work and no play makes Jack a dull boy...

    Old-skool Cobra buckets work brilliantly up front with rears trimmed to match.

    Dub Details

    ENGINE: 1.6-litre GTD from a MK2 Golf, ‘fuelling wound up, boost wound up’, Mk1 Series 1 radiator, front mount intercooler, custom solid boost pipes painted gloss black, Mk3 8v GTI rocker cover painted gloss black.

    CHASSIS: 8x16” #Fifteen-52 #Tarmac-348 two-piece wheels, ET5 front and ET0 rear with 165/45/16 Nankang NS2 tyres, #Havair #air-suspension struts, paddle valve management with a five gallon tank, #Viair-380 compressor, raised turrets, camber holes extended on front struts and turrets, camber disks on the rear hubs.

    EXTERIOR: Full repaint in the original Pragus Blue colour, late Westmoreland Rabbit front end conversion with #Hella Projectors, late Westmoreland Rabbit Long rear lights, Late Westmoreland Rabbit bumpers refinished in matt black, Rabbit rear side markers, GTI plastic arches, GTI A-Piller trims, #Zender three-piece spoiler, flared and cut arches, partially smoothed bay with the scuttle panel removed and hidden wiring.

    INTERIOR: Renewed door cards, new carpet, 80's Cobra bucket seats with the original rear bench trimmed to match, boot build fully carpeted with tank and compressor on show with hardlines. Gloss black painted Mountney steering wheel with a chrome centre.

    SHOUT: I would like to thank Cayla for putting up with my love for my cars, supporting me and helping me out with them. Big thank you to everyone at Rollhard, they helped me out massively last year, I couldn't have met a nicer bunch of people. Also a big thank you to the guys at Autoperfekt for keeping my cars clean. I would also like to thank Brad for the welding, Kyle and anyone else that's helped me along with the build process.
    Stream item published successfully. Item will now be visible on your stream.