Toggle Sidebar
News Feed

Currently filtering items tagged with #Eagle


  • Post is under moderation
    This BMW-E30 may appear relatively unassuming, but to the trained eye there are clues that all is not as it seems. No-one, however, will be expecting the self-styled 360i’s firepower…

    WILD CARD: BMW E30 WORDS DAN BEVIS / PHOTOGRAPHY CHRIS FROSIN 360 Kickflip 800BHP 5.8-litre E30!

    / #BMW-E30-V8 / #BMW-E30-GM-V8 / #BMW-360i-E30 / #BMW-E30 / #BMW-360i / #BMW-E30-800bhp / OK, #BMW didn’t make a 360i. But a chap called Ross did and it has two turbos, 800bhp and 5.8-litre engine!

    One of the questions I hear most often is ‘How did you get that in there?’” grins Ross Bradley, standing proudly beside his gleaming Black Cherry E30, exhaust ticking and pinging after another urgent country lane blast. “And that’s exactly the point – you make things fit. They don’t just go in there on their own.” That very much sums up Ross’s outlook on life.

    The joy of the project is as much in the build as the driving. ‘Built, not bought’ is a common phrase on the scene these days. Modifiers who’ve solely achieved their goals in the confines of a single garage with just a cup of tea and a crackly radio for company are rightly proud to wear their achievements on their sleeve. That’s not to sideline the opposing ‘bought, not built’ crowd, of course – we can’t all be experts, and there’s a whole flourishing industry set up to serve such purposes. But Ross’s history is very much hands-on, and that has informed this creation. He fancied doing stuff. Then he did it. It really is that simple.

    “I’ve always been toying with cars ever since I was little, being brought up with my dad building Yanks and hot rods,” he says. “I remember helping my dad build his Ford Pop when I was about seven years old, always doing what I could. With every car I’ve owned I’ve always had to rebuild something, be it the engine or interior for whatever reason, to make it better or make it my own.” And this is the case with the E30. The reasons for calling it a ‘360i’ will become apparent in due course. Suffice to say it’s very far from being a bone-stock 1980s three-box.

    “I always liked the E30,” Ross ponders. “I was going to get one for my first car when I started driving, but was talked out of it due to running and repair costs at the time. This was the late ’90s, so I went the Ford route and ended up having numerous Escort RS Turbos and so on.”

    Fast-forward to 2006, however, and we see that starry-eyed yearning of youth starting to come full circle. “I was out working and I saw this car on someone’s drive,” he recalls. “It had been sat there for about four years – it was a 320i, the body was in pretty good shape, although it had moss growing up the side of it, flat tyres, the usual. I offered the owner some money for it and he took it right away… I bought it for £275.”

    Game on, then. A childhood dream fulfilled and pretty cheaply too. All Ross had to do now was to make it his own. But he wasn’t going to rush into anything, he’d been waiting long enough to realise his E30 ambition so there was no need to charge in like a bull in the proverbial porcelain emporium. He used the car as a daily driver for a few years, doing bits and pieces here and there as he saw fit. New wheels, an M-Tech 2 kit, swapping the 2.0-litre motor for a 2.5. But then it all started to get a bit hairy. Suddenly that idea of doing it ‘cheaply’ wasn’t going to cut the mustard any more. It was time to commit, and commit hard.

    “About four years in I took it off the road and gave it a major overhaul,” he says. “New paint, new interior, suspension, wheels, brakes, the works. And I built the engine into a 2.5 turbo.” Of course, as your eager magpie eye will have probably spotted, that’s not the spec that the car enjoys today. You will no doubt have glanced over to the engine bay shots and spied quite a lot of cylinders in there. So just what the hell happened next?!

    “I used it like that for a few more years, until about four years ago when I again took it off the road and swapped out the motor for the Chevy V8,” says Ross, casually, as if that’s a perfectly normal thing to do. “It took me a further two years to build it from there; it was always going to be boosted right from the start - and then I had it on the road until, after a few problems last year with a couple of fires due to burst hoses, oil leaks, and turbos eating bearings, I’d had enough of the niggles. So last winter I took it off the road again and had another major overhaul!”

    OK. While you catch your breath and try to take in the sheer majesty of the spec list, let’s distil it down to the base elements: Ross is running a small-block V8 bored out to 5.8-litres (near as dammit to six litres, hence why he calls the car ‘360i’) with a massively juicy fuelling system, a pair of turbos that originally called an Iveco truck home, the sort of brutal internals more commonly found on drag cars, and a peak power figure somewhere around the 800bhp mark. Given the 1,300kg-odd kerb weight, that gives the car a similar power-to-weight figure to a Bugatti Veyron Super Sport – around 590bhp/tonne. All this from a reliable 3 Series built by one man in his garage.

    “During the most recent overhaul, I remade the exhaust manifolds and downpipes, and replaced the turbos with a set of Holset HX35s, and then got them ceramic coated,” says Ross. “I also sold my old red leather interior and put a new one together, with Recaro CS front seats and an E30 M3 rear bench, all custom-retrimmed by Lawrence at LG Trimming in north London.”

    While this car is all-motor on the face of it, the interior is one of our favourite elements. With the astonishing attention to detail going on under the bonnet it’d be easy to turn this E30 into a stripped-out drag monster, jettisoning anything that’d add unsavoury weight.

    So we love that Ross has brightened up his day-to-day commute with such a flawlessly executed and fashion-forward cabin. “With the interior sorted, me and my dad stripped the car down and repainted it in Black Cherry Candy, and after refitting with all new BMW window rubbers and so on it’s now what you see today… all the work apart from the interior was done by me, everything hand-made in my garage. So anything that I needed to make this work, I had to fabricate, as you couldn’t buy it off the shelf – the engine mounts, chopped-out rear end, remade gearbox mounts, you name it.”


    What Ross has created here is arguably the ultimate stealth weapon. Those who aren’t in on the secret may find themselves drawn to the car simply because it’s so beautifully presented. But there’s little to suggest anything’s radically altered aside from the subtle clues of the flared arches and front-mount intercooler. Indeed, peering through the window and spying that interior may convince you that it’s a mere show-pony. “That’s very much not the case,” laughs Ross. “I drive it as much as I can.” And with Bugatti-shaming power, wouldn’t you? It’s safe to say this car gets a pretty hard time on a regular basis.


    “I just love it,” he smiles, with the satisfaction of a job well done.

    “Most of my friends think I’m mental. But you only live once!”

    Ross is running a small-block V8 bored out to 5.8-litres.

    The car has a similar power-to-weight figure as a Bugatti Veyron Super Sport.

    Recaro CS front seats and an E30 M3 rear bench, all custom-retrimmed.

    ROSS BRADLEY

    You’ve put quite a lot of work into this, then?

    “Yeah, the amount of time I’ve put into it… I couldn’t put into numbers, really. It’s years. Years and years of hard labour!”

    Not really a budget build either, given the massive spec?

    “Ha! No, I’ve always thrown what I’ve got at it. It’s taken everything I have.”

    All plain sailing, though?

    “No real dramas. Couple of fires, turbos letting go, oil leaks… That’s just customising, isn’t it? There were points when I thought ‘It’ll never get done, never see the road,’ but I got it there. You’ve just got to keep pushing, haven’t you?”


    TECHNICAL DATA SPECIFICATIONS: BMW E30 #GM-V8

    STYLING Resprayed in Black Cherry Candy; rear arches flared and rewelded; M-Tech 2 BMW Sport body kit; front valance modified for intercooler.

    TUNING Early Chevrolet small-block #V8 rebored 0.030in to 5.8-litre; GM forged crank; #ARP main studs; #Eagle H-section forged conrods; #Clevite big end bearings; Probe oversized forged pistons; Melling high-volume oil pump; ported and polished alloy heads; Manley severe-duty stainless steel swirl-polished oversized valves (2.02in inlet, 1.6in exhaust); #Edelbrock valve springs with titanium retainers; Cloyes double roller timing gear and chain; Clevite cam bearings; Comp Cams 256/263-degree blower cam and lifters; Edelbrock magnum chrome moly pushrods; Comp Cams 1.5:1 alloy roller rockers; #Brodix rocker covers, ARP hardware (rocker arm studs, intake manifold bolts, sump bolts, timing cover bolts, engine mount bolts, exhaust header bolts, crank pulley bolts, bellhousing bolts); ARP oil pump driveshaft; custom engine mounts; hand-built custom turbo headers and downpipes; twin Holset HX35 turbos with 12cm² turbines; twin Tial 44mm wastegates; two-stage boost control; handbuilt custom twin 3in turbo-back exhaust with Simons silencer; custom intercooler; Tial 50mm dump valve; Edelbrock Pro-floinlet and matching fuel rails; Pro Comp 90mm throttle body; 770cc injectors; swirl pot with high-flow in-tank lift pump; twin Bosch 044 engine feed pumps; Torques pressure regulator; March serpentine pulley kit; Pro Cool alloy radiator; Megasquirt ECU; Ford Ka coil packs; fully lightened and balanced flywheel and rotating assembly; Toyota Supra Mk3 R154 gearbox with custom Chevy bellhousing adaptor – rebuilt and uprated with Marlin Crawler thrust washer; billet bearing retainer and selector forks; McLeod hydro clutch release bearing; ARP clutch bolts; Spec R Stage 4+ full-face paddle clutch; alloy fluid reservoir; Cube short shifter; custom propshaft; E28 M5 210mm LSD with 3.07 final drive and M3 Evo twinear rear mount; custom rear crossmember; custom driveshafts with UJs; custom gearbox crossmember.

    CHASSIS 9x17in #ET25 (front) and 10x17in ET20 (rear) #Hartge polished three-piece wheels; 215/40 (f) and 235/40 (r) #Federal-RSR tyres; custom billet aluminium centre caps; modified front crossmember for engine clearance; reinforced rear beam; E36 M3 front anti-roll bar with custom mounts and rose-jointed droplinks; reinforced rear trailing arms; custom rear strut brace tied into custom rear diff mounting bar; #Gaz-GHA coilovers; #GAZ adjustable front top mounts; stainless steel steering linkage joints and custom linkage; steering rack moved 20mm forwards; alloy power steering reservoir and custom lines; in-car brake servo conversion using Renault Clio servo; VW Sharan brake master cylinder; AP Racing six-pot front callipers and 330mm discs; five-lug conversion using E36 and Z3 hubs; Porsche Brembo six-pot rear callipers; Apec Z3 rear discs.

    INTERIOR Full custom retrim in Ruby Red nappa leather and black Alcantara; Recaro CS front seats with custom rails; E30 M3 rear bench in nappa leather with quilted design; doorcards in black Alcantara with quilted nappa leather inserts; dash, centre console, glovebox, handbrake, gear gaiter and roof lining in black Alcantara with matching stitching – by Lawrence at LG Trimming in Enfield, London.

    THANKS Thanks to Shaun at V8 Developments for the wiring and mapping; Dad for helping me paint it; and Lawrence at LG Trimming for the retrim.
    • While you lot usually love to hate anything wearing a BMW badge that doesn’t have a BMW engine under the bonnet, in the case of Ross Bradley’s twin-tuWhile you lot usually love to hate anything wearing a BMW badge that doesn’t have a BMW engine under the bonnet, in the case of Ross Bradley’s twin-turbo Chevrolet V8-engined E30, you just loved it as it is your 2016 Performance BMW Car of the Year.

      The engineering that’s gone into building this absolute beast of a machine, all of it done by Ross himself, is both mind-blowing and eye-watering in equal measure. The fully built, rebored Chevy small block V8 now sits at 5.82-litres and has been bolstered with a pair of Garrett T04E turbos resulting in a staggering 880hp. Fully polished 17” three-piece Hartges sit under widened rear arches, there’s a fully removable carbon bonnet, while the red Sport interior adds a bold splash of colour. You might not approve of that V8 swap, but this is such an impressive build that it’s impossible to hate.
        More ...
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    MK1 TT
    1.8T with 353bhp

    WIDE BOY With big arches and 10.5x18in alloys, this 352hp TT has some serious road presence…


    The original TT still ranks as one of the most significant Audis ever made. When this curvaceous, bold design was unveiled back in the late 90s, it made a huge impact. Here was a production car that looked very much like the original concept, and it was available to buy. Not only did it look fantastic, its performance credentials were strong, too.

    The venerable 1.8 20v turbo found in the S3 8L saw some upgrades, which took it to 225PS (221bhp). This gave the cool coupe lively performance, matched to a slick 6-speed manual box. With quattro drive, it hooked up the power and was quick off the mark, as well as surefooted when the going got slippery.

    With heated leather seats, a very cool looking dash and xenon lights it was a very nice thing to own. Back in 1999, a new TT would have set you back almost £30k. Today, you can pick one up for under £2,000, making them a bit of a bargain.

    Laszlo, the owner of the TT pictured saw the potential with a TT immediately.

    Having owned a big old Mercedes, he wanted something, small and sporty that was also fun to drive. A TT made sense – it was the right money and offered lots of tuning potential. “I wanted to switch from the yacht like feel of the Benz, to a stiffer, lighter sports coupe,” he says.

    Things began slowly with a simple air filter upgrade and ECU remap. But having seen lots of big power Audis around, it wasn’t long before the silver TT was sent to respected local tuning firm, Turbotuning.

    Here, the 1.8T was stripped down and rebuilt with fully forged internals including Mahle pistons and race spec bearings. The plan was to make the car as reliable as possible, so boost was held back to a relatively modest 1.5bar. Even so, with a Garrett GT2871 turbo, plus supporting upgrades, the TT made a very handy 352hp and 531Nm. Although we hear about plenty of 400+bhp models with large turbos, I have to say around the 350bhp mark seems to offer a great balance of performance and drivability for the road. I’ve been out in lots of TTs with this sort of power and they’re great fun. Plus, there’s less stress on the relatively small capacity 1.8-litre engine – something to take into account unless you liken spending time getting things fixed all the time.

    But there’s more to this TT than a decent bit of poke under the bonnet.


    Up front, Laszlo has fitted a set of six-pots from a Porsche 996. These big brakes required adapting to fit, but do an admirable job of stopping the little TT. With four pots at the rear and Ferodo DS pads, this thing scrubs off speed with aplomb.

    One area that any TT will benefit from upgrades is the chassis. In stock trim they’re quite soft feeling and set up for a neutral handling – as you’d expect. But with some tweaks, you can transform them. With a full complement of Powerflex bushes, the chassis and steering components now feel reassuringly tight, which translates into a much more positive feel to the steering and general handling. Bushes may not be the sexiest of upgrades, but they really do make a huge difference – especially on an older car, where the stock items are likely to be worn. With uprated anti-roll bars, the chassis is well set for hard use.

    One thing you can’t miss is the rather wide wheels. The 18in Japan Racing alloys are a huge 10.5 wide, which is why a set of, what the Americans like to call “overfenders” have been fitted. Some will love them others not so much, but you can’t deny they give this little TT serious road presence.

    A V6 TT front bumper has also been fitted together with the rear bumper insert, which looks much fresher. There’s also a V6 rear wing.

    Inside, Laszlo has really gone to town. The bucket seats have been trimmed in leather with yellow stitching with cheeky R8 logos. The R8 theme continues with the steering wheel and gearknob, complete with open gate.

    So there we have it. A Mk1 TT with an aggressive, OEM+ look, that’s also packing a nice punch thanks to the engine tuning – with the potential for a lot more should he wish to increase the boost and maybe fit a larger turbo.

    Top: Rear seats have been removed Below: 1.8T is forged and runs a GT2871.

    SPECIFICATION #Audi-TT-225 / #Audi-TT-8N / #Audi-TT / #Audi / #Audi-TT-Quattro / #Audi-TT-Quattro-8N / #Audi / #Quattro / #Garrett / #Garrett-GT2871 /

    Engine 1.8 20v turbo, Turbotuning shop rebuilt with #Eagle rods, #Mahle pistons, stronger bearings, low compression with rebuilt head, #Rothe turbo manifold, GT2871 Garrett turbocharger, 76mm exhaust system, custom exhaust with 90mm tips, custom intake, #Ramair filter, #HG-Motorsport intercooler 12-row #Motec oil cooler, F#orge BOV and boost controller, 630cc injectors, Walbro fuel pump

    Transmission 6-speed manual, stronger clutch with Kevlar disc, #Torsen rear diff
    Power 352hp and 531Nm at 1.5bar
    Brakes Porsche 996 fronts with 6-piston calipers, 4 piston rears, Ferodo DS pads and braided lines

    Suspension Custom rear control arms (GL), #Powerflex bushings all around, GL front strut bearing without damping, custom ARBs, #Eibach spacers, wheel bearings converted to studs, #Sachs dampers, custom air-ride setup with Viair compressor and #Airlift-Autopilot - #Air-Lift-V2 (tuned by #Fakukac )
    Wheels 10.5x18in #Japan-Racing-JR-11 wheels with 255/35 tyres
    Exterior V6 TT front bumper and rear insert, SEAT Cupra front lip, V6 TT rear wing, #EPMAN Racing bumper mount, Porsche green mirror housings, custom arch flares made up from Nissan SX kit
    Interior Bimarco bucket seats with Porsche-style leather upholstery and stitching, custom rear seat delete and crossbar, R8 steering wheel and gear knob, custom open gate, Osir gauge holder, Defi Stepmaster gauges, Porsche green details

    Left: Porsche 6-pots Below: R8 open gate gear lever.

    Right: R8 themed interior Below: R8 wheel and gearknob.

    “The TT made a very handy 352bhp and 531Nm”
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation

    ALL AMERICAN TAKE OVER

    Fitting a massive Yank V8 lump into your BM is nothing new, but doing that and then strapping a pair of turbos on for good measure takes things to a whole other level….

    Rebel yell Utterly insane twin-turbo V8 E30 with almost 900hp.

    After tiring of turbo M20 reliability issues, Ross Bradley went back to his hot rod roots and rebuilt his E30 using American V8 power… with two turbos this time. Words: Ben Koflach. Photos: Matt Woods.


    Meet Ross Bradley, an E30 nut who likes to do things his own way, particularly if it involves a twin-turbo V8. The story begins back in March 2010 when he bought this black 325i and, like so many of us, he formulated a plan to make it his own. “It was sitting on a drive for about four years with moss growing up the sides. I used to see it when I was out at work,” explains 35-year-old Ross. “It was pretty solid body-wise, so I offered the guy some money and bought it for £275. I got it home, changed the plugs and put fresh fuel in and it fired up first time!”

    Fast forward a year or so and his E30 was something we’d all be proud to call our own, featuring Borbet A wheels, a nice drop in ride height and a full M Tech 2 body kit, among other tricks. However, having grown up around American hot rods and other powerful machinery, it was only a matter of time before the engine bay got something of a shake-up.

    “I’ve always had turbo cars. I just have a passion for them,” Ross tells us. “And the BMW needed more power so the only way to go was turbo!” Ross laughs. The car’s transformation started with him taking the original M20 and turbocharging it, earning him the bragging rights of having over 400hp under his right foot. Having been an engineer by trade in the past he made it all look easy, building up the M20 with forged pistons, a custom intake plenum and plenty more goodies. Ross was happy until an oil pressure issue left him with a knocking bottom end and feeling thoroughly disheartened. Fortunately Ross isn’t the kind of guy to remain demoralised for long and he used this temporary upset as a chance to refocus. “I’ve always been a fan of proper V8s – not the little BMW ones but full-blown Ford or Chevy motors,” he explains. “Now that I had the chance, I decided to get rid of the old turbo engine which kept going wrong, and I sold all the parts to fund a new engine.”

    Ross’s plan for Yank horsepower made good sense. “I considered the newer GM LS engines but at the time they cost more than a complete S50, and you can just as easily build an old type V8 with EFI for half the price.” A decision was made and Ross was soon the owner of a small-block, 350ci (5.7-litre) block ready for building up. While Ross pressed on with using the bare block for test-fitting purposes, his shopping list started becoming a reality. A #GM forged crank, Eagle forged rods, a hightorque starter motor, alloy roller rockers and a new sump all arrived, with Ross’s plans continuously evolving for how the engine would fit in the car and how it would be built.

    “The gearbox I chose was the manual gearbox from the Mk3 Toyota Supra: the R154. With a couple of little mods they can be bombproof, but not cheap at £600 for the box alone!” Ross says. He was still waiting on engine parts but could at least get the gearbox built up. This would allow him to finalise the engine location once and for all.

    All new bearings went in, along with an uprated first gear thrust washer, before the front end was built up with a Chevy bellhousing, hydraulic clutch release bearing and all the necessary conversion parts. What soon became clear was that the E30’s transmission tunnel just wasn’t going to be big enough. Luckily it wasn’t beyond the call of a few hour’s work with a hammer. The next obstacle was the crossmember and anti-roll bar. A conversion to an E36 anti-roll bar (which sits ahead of the crossmember) had that issue solved easily enough thanks to some fabrication work, but Ross also had to notch the crossmember for clearance and ended up moving the steering rack forwards by 20mm to clear the starter motor.

    This left Ross with the small block sitting happily in his engine bay, as low and as far back as was possible. “The shifter even ended up in the right place!” laughs Ross. “There was just a sensor that I had to add clearance for, so things were going well.” With his engine and gearbox mounts fabricated, Ross then threw on the aluminium heads that he’d ordered and checked the clearance of everything with his turbo manifolds fresh from the States. Sure enough, his engine mounts had to come back out for some further clearance work and he had to make plans for relocating his brake servo and master cylinder to under the dashboard. For Ross this was all in a day’s work.

    With the engine position decided, Ross pulled the V8 block back out so that he could finally start transforming it into a functioning engine. The local machine shop was tasked with boring out the cylinders by .030”, taking displacement to beyond the 5.8-litre mark. Probe forged pistons were mated to the Eagle rods, with the crank going in with Clevite bearings and ARP hardware. His camshaft of choice was a Comp Cams 256/263-degree grind, made especially for turbo applications.

    Such is the aftermarket support for these engines that Ross managed to get his aforementioned aluminium cylinder heads for just £200 and set about porting them himself by hand to make the most of a set of massive Manley valves (2.02” inlet and 1.60” exhaust, in fact). This V8 may only have 16 valves but it makes up for that with sheer size. The heads were finished with Edelbrock valve springs and titanium retainers, which are operated by Comp Cams billet rockers and Edelbrock Magnum pushrods. No stone has been left unturned with this Yank powerhouse.


    A good old Holley carb was initially used to get the engine running alongside a Megasquirt ECU and Ford coil packs. Ingeniously Ross used a few of the old M20 sensors and brackets to feed the ECU with all the needed info, which allows the V8 to run normally aspirated for a few miles as a gentle run-in. A huge Pro Cool radiator, a custom intercooler and a day’s worth of custom fab work by Ross got the E30 roadworthy but he was far from done.


    When the time came to switch to fuel injection Ross, as usual, didn’t do things by halves. With the rear boot floor in bits (more on that in a moment) he plumbed together a fuel system capable of supplying enough jungle juice for the monstrous powerplant now sitting up front. A high-flow lift pump feeds a two-litre swirl pot, with twin Bosch 044 pumps then feeding the engine through front-to-rear braided AN lines. All that fuel is supplied to 770cc injectors mounted in an Edelbrock intake manifold, fitted with a 90mm Procomp throttle body.


    That swirl pot setup is mounted onto a flat rear floor. Ross’s car has no spare wheel well and for a very good reason. With the extra power and monstrous torque that he was going to be feeding through the rear end, some serious reinforcement was needed. The entire rear beam was dropped and stripped and Ross’s work began.

    The first thing on the ingredients list was an E28 large case diff; though it bolts right up to the E30 rear beam, that’s about where the compatibility ends; not a problem for someone like Ross. The beam was sent away for blasting and once back, he could begin. “I started by going over the old welds to make them a little stronger and I went around the trailing arm brackets again as some of them aren’t fully welded,” he explains. “Then I started the reinforcing.”

    These reinforcements included plating over the diff mounts and bridging together the various factory joins with extra material. Bars were then also added between the diff mount and beam itself before a thick plate was placed over the diff recess. In short, Ross’s work is so solid we reckon it would withstand even a nuclear strike.


    Next up was getting that diff mounted up. The E30’s single-ear rear diff mounting is famed for a lack of strength and so after some experimenting Ross found that an E36 M3 Evo diff cover and mounting bracket would bolt up to the E28 diff (with the addition of a spacer he made), giving him two ears to mount with. However, the E30 doesn’t have the provisions to bolt such an arrangement up, hence Ross had cut the boot floor out of his. A new crossmember was made out of box section, bridging the chassis rails and including mounts for that large case diff and the anti-roll bar brackets.

    “With the rear crossmember done I started the rear strut bracing,” Ross tells us. This included strengthening plates on the rear strut towers along with a welded-in strut brace. This was then joined to the diffmounting crossmember with a set of bars tying the whole lot together for maximum rigidity before everything could be sheeted over to form a new floor.

    The trailing arms were also braced with bars and then the whole lot bolted back under the car, complete with the new diff and a revision of Ross’s UJ driveshafts. However, he still wasn’t done, using the opportunity to also convert the car to fivestud all-round. Rather than the usual way, this arrangement was completed using Compact or Z3 parts with a bit of a custom setup. This consisted of Z3 wheel bearings and hubs, which needed a little machining to fit. “I used 300mm Z4 discs on the Z3 hubs, and then used Porsche Boxster Brembo fourpot calipers,” smiles Ross.

    Up front the E30 stub axles were sleeved to allow E36 wheel bearings and hubs to be used, enabling the use of an XYZ brake kit. It was originally meant for a Japanese application using a 5x114.7 PCD and Ross also had to make his own brackets, too. Nothing phases this E30 fanatic.

    Of course, the most noticeable change Ross had to make was to fit new wheels. The old 4x100 Borbet As would no longer fit but Ross found something else that would work nicely. It doesn’t get much better than three-piece Hartges, made by OZ back in the day. He found them in Poland and had them shipped over. They had polished lips and gold centres, which looked great, but weren’t quite what Ross had in mind. Therefore the wheels were stripped right down for the centres and lips to be repolished, and a lack of centre caps saw Ross approaching UK firm and BMW specialist Hack Engineering to reproduce the original plastic caps in billet aluminium so that it could all be polished up with the same mirror shine. Mirror-polished hardware finished the wheels off, with grippy Federal RSR tyres put in charge of getting all that power down.

    This meant that phase two of the build was complete, and Ross enjoyed using it for the latter half of last year’s show season, clocking up the miles attending every show possible. Having witnessed it personally, we can confirm that when Ross’s E30 pulls up at the showground, a serious number of heads turn thanks to the appearance of a tidy E30 with the soundtrack of a lumpy, all-American V8. It really is quite something.

    The way Ross has gone about building his E30 is like no other. While absolutely nothing on the car itself can be considered off-the-shelf, he’s also shown incredible ingenuity when it comes to building a reliable powerplant thanks to the strength (and low prices) of the American aftermarket. In fact, though untested, it’s estimated that the junkyard-rescued small block is currently pushing around 880hp and 750lb ft at 1.3bar. Could American power in an E30 be the way to go? You wouldn’t want to argue otherwise after seeing this machine.

    Boot houses fuel system with two-litre swirl pot and twin Bosch 044 fuel pumps.

    If you’re a keen show-goer in the UK you’re likely to see Ross’s monster throughout the year. However, do be warned – by the time it’s show season the E30 will be looking quite different. Ross didn’t want to tell us exactly what he was up to but you can rest assured that the E30 will be even better, very soon.

    DATA FILE #Twin-turbo #V8 / #BMW-E30 / #BMW / #BMW-E30-V8 / #Bosch-044 / #Garrett-T04E / #Garrett /

    ENGINE #Chevrolet-small-block-V8 , rebored 0.030” to 5.82-litre, #GM / #GM-V8 forged crank, #ARP main studs, #Eagle H-section forged con rods, #Clevite big end bearings, Probe oversized forged pistons, high volume oil pump, ported and polished alloy heads, #Manley-Severe-Duty stainless steel swirl-polished oversized valves (2.02” inlet, 1.6” exhaust), Edelbrock valve springs with titanium retainers, #Cloyes three-piece solid timing gears, Clevite cam bearings, Comp Cams 256/263-degree blower cam and lifters, #Edelbrock #Magnum chromoly pushrods, #Comp-Cams 1.5:1 alloy roller rockers, #Brodix rocker covers, ARP hardware (rocker arm studs, intake manifold bolts, sump bolts, timing cover bolts, engine mount bolts, exhaust header bolts, crank pulley bolts, bellhousing bolts), ARP oil pump driveshaft, custom engine mounts, customised turbo headers, twin Garrett T04E turbos, Tial wastegates, custom twin 3” turbo-back exhaust with Simons silencer, custom intercooler, Tial dump valve, #Edelbrock Pro-flo inlet and matching fuel rails, #Procomp 90mm throttle body, 770cc injectors, swirl pot with high flow lift pump, twin #Bosch 044 engine feed pumps, #Torques fuel pressure regulator, #March serpentine pulley kit, #Pro-Cool alloy radiator, #Megasquirt ECU, Ford coil packs, fully lightened and balanced flywheel

    TRANSMISSION #Toyota-Supra-R154 gearbox rebuilt and uprated with #Marlin-Crawler thrust washer bearing retainer and selector forks, #McLeod clutch release bearing, #ARP clutch bolts, Spec R Stage 4+ paddle clutch, alloy fluid reservoir, #Cube shifter, custom propshaft, E28 210mm LSD with 3.07 final drive and M3 Evo twin-ear rear mount, custom driveshafts with #UJs , custom gearbox crossmember

    CHASSIS 17x9” ET25 (front) and 17x10” ET20 (rear) Hartge fully polished three-piece wheels, 215/40 and 235/40 Federal RSR tyres, modified front crossmember for engine clearance, reinforced rear beam, E36 M3 front anti-roll bar with custom mounts and rosejointed droplinks, reinforced rear trailing arms, custom rear strut brace tied into custom rear diff mounting bar, #GAZ coilovers, GAZ adjustable front top mounts, stainless steel steering linkage joints and custom linkage, steering rack moved 20mm forwards, alloy power steering reservoir and custom lines, incar brake servo conversion using Renault Clio servo, VW Sharan brake master cylinder, #XYZ six-pot front calipers and 330mm discs, fivelug conversion using E36 and Z3 hubs, Porsche #Brembo six-pot rear calipers, #Apec-Z4 rear discs


    EXTERIOR M Tech 2 body kit, carbon bonnet, E36 M3-style mirrors, widened rear arches, smoked rear lights, smoked front indicators, yellow foglights

    INTERIOR Full red leather Sport interior, black carpets, custom gauge illumination (blue with red needles), A-pillar mounted auxiliary gauges (boost, #AFR , oil pressure), fuel system in boot

    THANKS Dad for all of the paintwork, Shaun from V8 Development for all the mapping and wiring.

    Red leather Sport interior looks fantastic and features custom gauge illumination and auxiliary gauges in the A-pillar.

    I’ve always been a fan of proper V8s… full blown Ford or #Chevy-motors .
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    WHITE LINES / Words Davy Lewis Photography Jape Tiitinen.

    600BHP SNOW PLOUGH
    Wide-body #Audi 80 quattro. This 603hp, wide body #Audi-80-GTE was built for one thing – hooning on the frozen roads of Finland…

    Our man in Finland, Jape, is always sending us cool videos. When he’s not taking amazing images of some of the world’s most exciting, and indeed powerful Audis, he’ll be capturing them in action. From riding shotgun in Philipp Klaess’ insane 225mph, 1000bhp B5 wide body, to Gatebil monsters, this man knows no fear. It was when one of Jape’s emails pinged into my inbox that I discovered this beast of an Audi 80.

    The email simply said, “Hi Boss, check out this Audi 80 snowplough!” There was a link to a video in which a tough looking 1980s saloon was being given death in the snow. It looked like tremendous fun. The driver was clearly having the time of his life in this wintry playground, and given the pummelling my ears were getting from my headphones, it was clear that this thing was running a rather large turbo.

    So I pinged Jape an email to find out more... Turns out the owner is a good friend of his, which doesn’t surprise me – everyone seems to be a mate of Jape’s – even our own Julian Loose in the UK (is there anyone Jape doesn’t know?!) The lucky owner of this ultimate snow toy, is a chap called Pasi Kellokumpu. A well known face on the Finnish tuning scene, he runs a trailer company transporting cars all over the place. But when Pasi isn’t towing cars, he’s driving them – sideways.

    It’s no secret that the Fin’s seem to have an innate ability to go incredibly fast, in the kind of conditions that would make us Brits scared to set foot outside the house. The joke about needing a wiper on the side windows is actually closer to the truth than you might imagine. But, even in this country filled with expert sideways merchants, Pasi is still regarded as a bit of a lunatic.

    Now that really must take some doing in Finland! The Audi 80 is however a mere toy for this guy. You see, tucked away in his garage, are a couple of serious power cars that he only drives in the good weather. There’s a 1000+hp Ur-S4 for track and an insane S2 packing a mighty 1319hp – surely the most powerful in the world. This out-and-out drag monster is named “Aim and Pray” which kind of says it all really. We’ll be featuring both of these truly epic cars as soon as the winter releases its icy grip on Finland. The 80 GTE is then a mere toy – something to keep him amused over the long winters. It may be a ‘toy’ to Pasi, but for most of us, it’d be a dream come true.

    Based on a 1986 Audi 80 GTE quattro, this once sedate saloon has been transformed into a full-on hooligan. Under that Sport quattro-style vented bonnet, sits a fully built 2.2 5-pot lump running a #Holset HX40 turbo. This behemoth blower, together with supporting upgrades, including straight through 3in exhaust, huge 4in downpipe, massive intercooler, and uprated fuelling, helps this thing make 603hp and 660Nm.

    When the big Holset comes on song, all hell breaks loose – perfect for playing in the snow. All four wheels light up in an instant and big, four-wheel drifts are easy. It’s loud too. That five cylinder howl sounds all the more glorious with the turbo chuffing and snorting away as Pasi bangs through the gears.

    Talking of cogs, with more than three times the stock power, this Audi 80 has been treated to a heavily uprated box. It’s an S4 01E six-speed unit that’s bolstered by a Sachs Race 3-paddle clutch and S2 driveshafts. A lightened flywheel helps things rev – something this engine has no problem with already!

    Pasi has fitted a set of Brembo brakes from a Leon Cupra R together with some S2 rear discs. This setup provides ample stopping power – when the tyres have something to grip on, of course. But then the 8.5 and 9.5x17in Fondmetal rims aren’t shod in your average ‘winter’ rubber; this thing runs proper studded tyres. However, when the snow has cleared and the sun returns to Finland, Pasi swaps to some girthy 10 and 11.25x17in wheels, which I’m reliably informed, look amazing.


    Aside from the rip-snorting engine and bullet proof transmission, there are plenty of other treats built into this supersnow saloon. Inside, it’s all about performance; anything that wasn’t required was chucked in the bin. All you’ll find now are go-fast aids, such as the multi-point roll cage (handy when you’re only ever a hairs breadth away from sticking it on the roof), a pair of deep Sparco buckets with 6-point harnesses, and a tactile Nardi wheel. Once snuggly ensconced within this setup, the driver can concentrate on the task in hand – going incredibly fast. A smattering of gauges keeps Pasi abreast of the engine’s health – and that’s about it.

    For me, the best bit of this monstrous little saloon is the looks. There’s no poncey ‘patina’ about this badboy. It’s battered, battle scarred, and proud – like those old fellas with flat noses you see in the pub – you can tell it’s lived an exciting life.

    The styling is heavily influenced by the Sport quattro – and why not? It’s one of the most iconic and downright cool looking cars ever made. There’s a Sport quattro-style front bumper, grille and even bonnet. The bonnet features vents to help cool the engine, but it’s not all show – it’s made from carbon fibre. And so is the roof for that matter.

    The front bumper has been viciously cut out to allow maximum airflow to the large intercooler and rad. To the rear you’ll find a Ur-quattro style bumper, plus a cheeky Audi 80 V8 rear light panel that’s been modified to fit and a cool looking rear diffuser. But, for me, the icing on the cake is the full set of custom steel fabricated arches designed to mimic the Sport quattro’s wide shouldered look. The rear doors have also been heavily worked on to complete the look – it’s as if Audi made a four-door Sport quattro. This Audi 80 looks squat, muscular and ready for business.

    So what’s next for this 600hp snow plough? Well, according to Pasi, the engine is being taken to 800-900hp for next season. Looks like things are set to get a whole lot crazier in Finland!

    Top: Front is all about the airflow Above: Ice, ice, baby...

    SPECIFICATION #Audi-80-GTE-Quattro / #1986 / #Audi-80-GTE / #Audi-80-Quattro / #Audi-80 / #Audi-80-B2 / #Audi-80-GTE-Quattro-B2 / #Audi / #Ur-S4 / #Ur-S4-AAN / #Audi-S4-01E /

    Engine #Audi-Ur-S4-AAN 2.2 5-cyl 20v turbo engine, #Eagle con rods, #Mahle pistons, upgraded piston pins, #Schrick high-lift cams, upgraded valve springs, Revo adjustable cam gear, #Dahlback-Racing pulley, 4in #Revo downpipe, #Holset-HX40 Super turbocharger, #Tial wastegate, custom intercooler, VW Vento radiator, 034 Motorsport coils, #Tatech ECU, 3in custom exhaust, #Fuellab fuel pump, fuel cell in boot.

    Power 603hp and 660Nm

    Transmission #Audi S4 01E six-speed box, 4WD, #Ojennus lightened flywheel, #Sachs Race 3-paddle clutch, S2 driveshafts

    Brakes SEAT Leon Cupra R #Brembo calipers (f/r), Leon Cupra R front discs, S2 rear discs

    Suspension: #H&R S2 coilovers, S2 anti-roll bars, faster steering rack (RS2), polyurethane bushes

    Wheels & Tyres Summer: RH ZW1 10x17in (f) with 11.25x17in (r), 235/45 (f) with 255/40 (r). Winter: Fondmetal 8.5x17in with 9.5x17in, 225/45 (f) with 245/40 (r) studded.

    Interior: #Sparco Evo racing seats, #Sabelt 6-point harnesses, roll cage, Nardi steering wheel, rear seat deleted, stripped interior, #VDO 300km/h speedometer, A’PEXi rev counter, #VDO gauges for boost, water temperature, oil temperature, oil pressure and voltage, #PLX gauges for fuel pressure and AFR.

    Exterior: Sport #Quattro -style front bumper, #Sport-quattro-style grille, carbon fibre bonnet with Aerocatches, VW Transporter front lights, Sport quattro-style custom steel wheel arches, custom steel side skirts, custom rear diffuser, Audi 80 V8 model rear light panel modified to fit, #Audi-Ur-quattro style rear bumper, carbon fibre roof.

    Tuning contacts/thanks www.erihinaus.fi


    Facing page: Pasi runs a towing company Top: Custom rear diffuser Above: Full cage and Sparco seats Left: Just the essential dials.

    “Big, four-wheel drifts are easy in this thing”

    Above: Big Holset turbo dominates the bay Below left: 20v turbo five makes over 600hp Bottom: Boot houses the alloy fuel cell.

    Above: Are you winding me up?! Below: The ultimate snow toy Bottom: Side-exit pipes.


    See it in action… To see a video of Pasi hooning around in some full-on Finnish snow, head to https://drive-my.com/en/social/stream/item/7610.html
    Stream item published successfully. Item will now be visible on your stream.
  • Post is under moderation
    NOW AND THEN, A BAD-ASS MUSCLE CAR ROLLS INTO TOWN AND TRUE TO TRADITION, WE’RE THE FIRST TO GIVE YOU THE SCOOP!

    Gavin Wilkins gave us a call explaining to us that he has a very important car laying in his workshop. In true Gavin Wilkins' tradition, he gave us a few basic clues, like the car was supposedly an American muscle car with a hefty 8-cylinder motor, and was supposedly modified there too. But a few weeks before, we came to hear of a rather unique #1971 #Plymouth #Cuda , a 2-door coupe which had arrived on our shores, and I began wondering if this was the said Unicorn. Now, dear readers: photos and print media do not tell the true mastery of this Cuda. It has to be seen in person to understand this car's enormity. A few years back, a chassis building company in the USA named Morrison were commissioned to oversee the project of restoring an old Plymouth. Over and above the channelling process where the Cuda's body was lowered to hang 4" over the frame, subtle mods such as shaved drip rails, a custom front valance and air dam, and those erotic side fender grilles were all crafted by the team at Morrison.

    But in all honesty, I think it’s the way the meticulous matte paintwork contrasts against the bits of orange which adorn the rear fenders. Or maybe it's the way the fenders hug those devilishly custom-made Intro Wheels which are 20 and 18" large? Or could it be the way the Strange coilovers are joined in holy matrimony with the Watts link rear suspension and the Corvette C5 front suspension which together, have created the perfect stance for the perfect American muscle car? I just don’t know. But what I do know is that this blurry indecision makes me yearn for a cup of tea.

    Swing open the driver's door, and nothing much grabs your attention except for those white dials, the Momo steering wheel and those RCi 5-point race harnesses. But weirdly though, once you sit in those superbly covered sport seats, and run your hand over the suede roof lining and notice the Morrison-built rollcage, you begin to understand that everything inside the cockpit is there for a reason. Besides the welcoming addition of electric windows, those elegant billet pieces on the steering column, and the TCi Outlaw shifter - which screams to be grabbed - is all part and parcel of the Cuda's theatre.

    The front of the car is where the party happens: Over and above the grille and headlights which came off a 2009 Challenger, the hand built shaker hood (a fancier name for the air intake which moves with the engine f movement)is what lures you to the bonnet in a trancelike state.

    Unclick the bonnet latches to pop the Cuda's hood and the motor resembles something out of Hollywood. Coated in what looks like sugary candied orange, the Hemi motor is a work of art, and when it awakens, things start a-shaking...

    I can honestly say that the engine is massive. Last time I saw something this huge, I flew in it to Europe. Barely squeezed into that painstakingly smoothed and shaven engine bay, lies an angry, 605 cubic inches Hemi monster, and let me tell you, it swallows fuel at an alarming rate.

    “Look, this thing guzzles hey." laughs Gavin. “You can let it idle, and in a few minutes, that fuel gauge needle will start going down. If you had to drive from Alberton to Eastgate, you’ll probably run out of fuel." The impetus for this whole project began in Indiana by a specialist cylinder head company named Indy Cylinder Heads. In addition to their line of big and small block #Mopar and AMC heads, Indy also build complete engines and are synonymous for the being the best at what they do.

    The motor powering this 'Cuda is a spare-no-expense, take-no-prisoners powerplant using a Maxx aluminum block, an Eagle 4750 steel crank, and humungous Diamond 4.500 forged pistons-115mm in diameter (let that sink in for a while)- down below.

    Topside is a pair of their Legend series heads with full CNC port and polish, bigger valves and thicker L19 ARP bolts and studs. Naturally, a COMP Cams solid roller thumps the lifters up and down and gives just the right signal to the big #King-Demon-1,050-cfm carb sitting atop the high-rise intake. In addition to the 511 hp on the wheels - which Gavin proudly states is the highest street car reading he's ever had at GWR - this bad boy rips the dyno in half with over 780Nm of torque, even more impressive on pump gas!

    “When the car arrived at my workshop, the engine needed some TLC - it was tired and the body had to be reprayed by Dinos. There were so many other niggles which we sorted out too - mainly after hours because there was no way I was going to work on an engine of this magnitude with other distractions happening around me. One mistake can be very costly."

    When the metal industry closes up shop for the weekend, and the roads in and around GWR have quietened down, Gavin takes the car around the block for a quick test and returns with a smile from ear to ear.

    “The car rides beautifully. It's built right and it shows as it drives perfectly and solidly without any drama. It's a real cruiser and attention grabber!" explains Gavin as he switches off the car.

    The car is to be returned to the owner in a matter of days, and as Gav wipes off a bit of dirt off the fender, he ends, "This particular owner loves his cars to be done right: he's a perfectionist who appreciates the finer forms of the automobile, and I'm grateful to have worked on this' Cuda. It's a one of a kind car, with a one of a kind attitude."


    THE ENGINE BAY LOOKS LIKE SOMETHING FROM A TRANSFORMERS MOVIE.

    QUKKSPECS #1971 #Plymouth-Cuda-2 Door-Coupe / #Plymouth-Cuda-2-Door-Coupe / #Plymouth-Cuda

    ENGINE: #605-Hemi / #Hemi - Maxx aluminium Hemi block - Eagle con-rods - #Eagle 4.750 crank - #Diamond 4500 pistons – #Federal-Mogul race bearings - #ARP L19 bolts and studs - Indy aluminium hemi cylinder heads - Indy roller rockers - #Comp-Cams solid roller camshafts - 3" exhaust - #Flowmaster mufflers - MSD 6AL custom fuel tank - Edelbrock fuel pump and fuel pressure regulator – #King-Demon 1050cfm carburetor.

    TRANSMISSION / DRIVETRAIN: 2-speed auto transmission - 9" Ford rear differential - TCi heavy case #Powerglide transmission - 3" Morrison propshaft - 35-spline #Morrison driveshafts.

    WHEELS / TYRES: Custom 20" x 12j Intro Wheels (rear) and matching 18" x 8j (front) Intro wheels in the front - #Pirelli tyres. Suspension: Full Corvette C5 front suspension - Watts Link rear suspension - Strange coilovers.

    BRAKES: 6-pot Wilwood calipers -14" #Wilwood brake discs. Exterior: Full respray by Dino’s Autobody - Morrison-built full chassis - 2009 Challenger grille and headlights - hand-built #Shaker hood - billet hood hinges - shaved drip rails - custom front valance and air dam.

    INTERIOR: Full leather and suede interior - RCi 5-point harnesses electric windows with power steering - Morrison-built rollcage - TCi shifter - custom white guages - billet aluminium column stalks.

    The custom intro wheels are spectacular. Wilwood provides the stopping power. The rear is rounded off with two Flowmaster mufflers. The modern #MOMO steering wheel pops against the classic interior. RCi 5-point harnesses clip you in.
    Stream item published successfully. Item will now be visible on your stream.