- Post is under moderationBMW E46 M3 SMG Issue
/ #BMW-M3-SMG-E46 / #BMW-M3-E46 / #BMW-M3-SMG / #BMW-M3 / #BMW-SMG / #BMW
I thought I’d write in with a query about my car to see if anyone has any suggestions – or if BMW Car’s resident expert, Andrew Everett (my favourite writer), has any thoughts?
I have a #2005-BMW-M3-Convertible-SMG-E46 with the #SMG-transmission and approximately 80,000 miles. It has had the usual issues associated with these cars but I still love it – once you’ve learned how to drive with SMG I strangely prefer it to a manual.
It’s had the boot floor reinforced, the Vanos system rebuilt at Mr Vanos in Darlington (www.mrvanos.com) and the dreaded SMG problem (almost) fixed. The gearbox decided it didn’t want to choose every gear when asked so I drove it to my local BMW dealer recently in Cumbria (used for over 30 years). They looked and diagnosed the hydro-electrical actuator as the problem, unfortunately after this was replaced it still didn’t ix the issue. The detent springs on the gearbox were then replaced and finally gears could be selected with a final bill of £4500. I drove it home and all seemed almost fine with life.
I only use my M3 for longer journeys. After two weeks of it not being used, for the first five minutes first gear was met with some vibration and reluctance for drive to engage. As if the clutch or flywheel were not being engaged properly. All other gears were fine. This problem was not there before the initial SMG problem (the original clutch and flywheel were not replaced). After a few miles the problem disappeared and taking of in first gear was totally fine. I’m not an aggressive driver, I’m mechanically sympathetic to my car and the SMG selector is always left in the middle setting. As for Sport mode... I enjoy having my licence too much so it’s never used.
I again left the car sitting for a couple of weeks and was met with the exact same problem with first gear. Before I return to my BMW dealer (and yet another bill) I was wondering if anyone could shed any light on this issue?
Stream item published successfully. Item will now be visible on your stream.
- This could be a few things.... We spoke to ex-BMW Master Tech Barry Sheward at BMR Performance (www.bmrperformance.co.uk). Firstly, you need to be takThis could be a few things.... We spoke to ex-BMW Master Tech Barry Sheward at BMR Performance (www.bmrperformance.co.uk). Firstly, you need to be taking this back to the dealer that did all the work as it’s clearly not right. For £4500 we guess it’s had either the actuator on the gearbox replaced or the SMG pump under the inlet manifold/airbox – or both. If it’s on the original clutch then this may be the problem – even if the clutch plate still has meat on it, it could be dragging on the gearbox input shaft splines due to a build-up of dirt on the clutch release fork, the plastic pivot and the metal release bearing sleeve will all be very well worn by now. The release bearing wears a groove on it and can stick. The flywheel should be alright at 80k.
The first thing is to get the fault codes read – these need to be proper BMW codes and not just generic P codes, the clutch should be bled through twice as well. If no fault codes are showing then it is bound to be a mechanical wear issue, and a new clutch with all the parts mentioned above need replacement; clutch kit, clutch fork, release bearing sleeve and plastic pivot pin.
- Post is under moderationE30 M3 STAYS COOL AT 215MPH / #BMW-E30 / #BMW / #BMW-M3-E30
A tuned E30-generation #BMW-M3 has broken the ice speed record in Sweden. Buldre Racing Team recorded an average speed of 212mph at the Swedish Speedweek in Årsunda, recording a high of 215.5mph on one run.
As you might have guessed, it’s no factory-spec M3, though – under the bonnet is a #Toyota-2JZ pumping out 1300bhp. This beats the team’s previous effort in an Audi RS4, which had the safety net of four-wheel drive...Watch it at
Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationMARK B’S #BMW-E30 / #BMW-M3 / #BMW-M3-E30 / #BMW-3-Series / #BMW-3-Series-E30 / #BMW
Well it’s been a busy month or so and I’m pleased to be able to say that all remains well with my E30 M3. In fact, a recent trip up to Silverstone for the Pistonheads Sunday Service saw me cover nigh-on 550 miles in one day.
The only real drawback with living here in Cornwall is everything else is just so bloody far away! Oh and that we don’t have a race circuit, although once my lottery millions roll in I plan to remedy that situation with a mini Nürburgring! I simply need to win the lottery first! Anyway, I had never driven Silverstone before, but the Pistonheads event had 30 minute sessions available for just £40, so I figured it was worth the trip. As well as a chance to get out on track there is usually a good mix of cars there to drool over and there was even a bit of sun forecast to make an appearance. I also knew that Sam Ratcliffe was due to be there in his stunning E46 M3 track car, which is just about my perfect specification. Added to which he can pedal a bit and who doesn’t like seeing an M3 getting used properly on track? In fact, look up DannyDC2 on YouTube and you can see both Sam and Dan driving their M3s back at Silverstone a week or so later.
Anyway, the trip up in the E30 went without incident, although it has to be said that the Nankang AR-1 tyres aren’t exactly ideal on a cold autumn morning. I did consider swapping over to my spare wheels that wear an all-weather Toyo TR1, but as the forecast was for dry and bright weather I figured it best to stay with the Nankang and just be a bit more careful driving up. Once I was within a few miles of Silverstone I soon began to spot other cars heading to the same event. I ended up in convoy with a pair of serious-looking Caterhams, a stunning blue 911 GT3 and a Clio Sport. It reminded me just how useful a roof and windscreen are as the Caterham looked a bit of a chilly and damp place to be thanks to the early morning drizzle.
Once we reached the circuit I was directed to the pit garages, while the rest of the convoy went into the main car park and joined the rest of the event. There were so many great cars there and a few rarities, such as the Renault 5 Turbo 2 and a pair of Nobles. There were several of the usual suspects that you see at track days, such as a 911 GT3 RS and the later incarnations of the M3 and M5, with a lovely track-prepared E34 M5 being a favourite of mine. The drizzle had stopped but the track was still pretty wet and there was certainly no visible dry line. Sadly one unlucky M3 owner had a pretty big off and wiped out the front of his car in a big way. Fortunately he wasn’t hurt, though, and an initial inspection suggested his M3 wasn’t beyond repair. It was still a sobering reminder of how quickly things can go wrong if you push a little too hard or get caught unaware by changing track conditions.
The time for my sessions soon rolled around and I lined up in the pit lane behind a lovely-looking Noble. The track had been drying out but there were still lots of wet patches to look out for and I knew my tyres needed a bit of heat before they’d have any real grip. There was also the added factor that my only experience of Silverstone was driving it at home on the PS4 and Project Cars, where spinning out in a Group A E30 M3 doesn’t matter. I opted to try and stay to the right (letting the faster cars past with a cursory flick of the indicators to confirm my intentions) and simply enjoy being on such a historic track and being able to really stretch the E30’s legs. One of the many things I love about the E30 M3 is just how communicative the chassis is. It’s just so easy to feel exactly what the car is doing beneath you and the feedback through the steering means that even clumsy amateurs like myself can make a reasonable job of putting a respectable lap in. The more laps I did, the drier the racing line got and the more my confidence grew. The only downside was that the KW Competition suspension I run is just a bit too firm for wet conditions. Ideally you want a bit of body roll, so the weight shifts and pushes the tyre contact patch into the tarmac, so I could have disconnected the ARB if I’d had more time, but it was still great fun all the same and reminded me just how capable the E30 M3 really is out on track. I had a couple of moments going into the faster corners where the inside rear caught the wet outer edge of the track and lost grip but it just made me more determined to go back once spring gets here next year.
The drive home (after checking the engine oil, coolant, tyre pressures etc.) was just as uneventful as the drive up. I always enjoy seeing people react to spotting a track prep’d E30 M3 go past amongst a sea of modern Euro boxes, though. The engine has been great and, even out on track, the oil and coolant temperatures stayed perfectly constant, as did the oil pressure. I’m off to Mallory Park in late November so will need to change the oil and filter before then and have Joe at ARM BMW do a spanner check. I also plan on fitting some new brake pads from Pagid and fitting a vinyl sun strip on the windscreen now that the winter sun is so much lower, as the cage stops the OE sun visors from being used. I’m also thinking of getting Apex to supply a set of their stunning dished ARC-8 alloys.
THANKS Joe @ ARM as ever Pistonheads Sunday Service Silverstone Circuit Nankang UK Apex
BMW E30 M3 felt at home around Silverstone.Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationMARK B’S #BMW-E30-Coupe / #BMW-M3 / #BMW-E30 / #BMW-M3-E30 / #BMW / #BMW-S14
Since rebuilding the engine a few months back, I have tried to use the M3 whenever I can and it finally has the reliability it should have had. The engine performance is really strong and using the M3 in competition meant I was able to really drive it harder than regular driving allows. I kept the rev limit to just over 8000rpm for longevity and while 250hp isn’t much by modern M3 standards, combined with a shorter final drive and the low weight of a partially-stripped #BMW-E30 , you have a car that’s quicker than you might imagine. The combination of induction noise (thanks to the DTM carbon air box) and harder edged exhaust tone (from Eisenmann’s excellent Race exhaust system) only add to the experience. Whilst I always loved the look of the old ex-works race car clocks, they just didn’t allow me to keep close enough an eye on what was going on within the engine, which is why STACK suggested I run their classic analogue rev counter and LCD display. I must say, I am glad I followed their advice as having literally every parameter covered and the information available at my finger tips has meant I have total confidence in the BMW-S14 and its health. I can’t say it hasn’t been a pretty steep learning curve, especially when it comes down to learning which modifications work and which don’t, but I’m finally at a point where everything has come together. The additional cooling (thanks Rad-Tec) and tricks like remounting the oil cooler (albeit a slightly larger Mocal unit) mean the engine now runs at its optimum with power and performance being consistent no matter ambient temperature and altitude, thanks to running DTA Fast engine management. This wasn’t the case with Alpha-N, when the car could feel totally different from one day to the next. It just seemed incredibly sensitive to changes and I’m sure that wasn’t good for the engine. Thankfully that’s all in the past now.
This past week saw MOT time roll around again (where does the time go?!). Thankfully ARM take care of this for me and as I know there’s no corrosion to worry about, plus the mechanical side is about as well maintained as it’s possible to be, I really didn’t have too many concerns. Usually it’s something trivial like the headlight adjustment or a blown bulb but this time it was a straight pass with no advisories. Job done! We also did a gearbox and LSD oil change as I plan on doing a track session at Silverstone at the end of November. I’ve never driven Silverstone before, apart from in Project Cars on the PS4, so I’m really looking forward to driving such an iconic track. The video from Petrolicious is also live now and I must say thank you for the positive comments. It’s been a tough few years if I’m honest and I have some more tough times ahead, so I’m extremely grateful. Sadly this may mean my selling the E30, although I am currently trying to find an alternative solution, but please feel free to contact me should you be interested.
Mark’s awesome M3 in action
Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationTOM WRIGLEY’S #BMW-M3-Competition-Pack-F80 / #BMW-M3-F80-Competition-Package / #BMW-M3 / #BMW-F80 / #BMW / #BMW-3-Series / #BMW-3-Series-F80
I started my last ‘Our Cars’ entry back in the Summer issue apologising for missing a few months’-worth of updates, and here I am writing this this month having done exactly the same thing. Even the excuse is the same – I’ve just been so busy with work at the karting centre and with my racing in the Porsche Carrera Cup GB with team MSS Kits that I’ve just not had time to put fingers to keyboard. Nor have I done much to the M3 either, but I do have a reason for that. You see, I’ve decided I’ve had my time with the #BMW-M3-DCT-F80 M3 Competition Pack and I fancy something different.
Don’t get me wrong, I’ve thoroughly enjoyed my time driving and modifying her, and she definitely ranks as one of my favourite cars I’ve owned, but it’s time for a change. But don’t worry, I’m not straying from my beloved BMW. I thought to myself, what could possibly be better than an F80 M3? Well I guess, logically, the answer is an F90 M5! I’ve been a bit obsessed with the latest M5 since seeing and reading the reviews a little while back, and while some people weren’t sure about the M5 losing one of its USPs at first, personally I liked the idea of that clever four-wheel-drive system, and of course its 600hp and 553lb ft V8 engine too. So, it’s time to say goodbye to the M3. As so often happens (I’ve read enough PBMW features to know I’m not alone in having done this!), I’d gotten her right where I wanted her and then… decided to sell. I know, I know, but you know what it’s like when you get the taste of a new car. Anyway, before I wave her off to pastures new I thought I’d run down the final spec how she stands now.
The highlight of the whole build for me was definitely the #Tom-Wrigley-Performance #AP-Radi-CAL II 390mm six-pot and 380mm four-pot front and rear brakes I developed. They absolutely transformed the way the car stopped on the road and on the track, giving such a nicer pedal feel and, on track, being much less prone to fade. I liked the way the M Performance carbon exterior pack and the CS front splitter looked on the outside, just as much, in fact, as I liked the M Performance carbon and Alcantara interior pack, the trick LED wheel, the amazing sounding and performance-boosting exhaust and, in my eyes anyway, the awesome looking #763M-wheels . In fact, I liked pretty much everything about this car it’s got to be said. Under the bonnet I fitted the three-piece CSF cooling kit, which did definitely make a difference in keeping things cool on track, the stunning looking (and sounding!) Arma Speed carbon intake and of course the Evolve Automotive cat-less downpipes. Finally, and probably the thing that made the most difference performance-wise, I had Evolve install one of its Stage 2 maps, with pop and crackle overrun for the giggles. In fact I liked the noises it made so much that the fact Evolve’s brilliant map really made a noticeable difference to the car’s responsiveness and overall drivability and added an extra 60-70hp and 70-80lb ft torque too was almost a bit of a bonus!
I also want to take this opportunity to thank #Evolve-Motorsport , CSF and #Arma-Speed for working with me on the car and I look forward to fitting some of their brilliant products to my cars in the future. You know a product is good when you’re already thinking of going down the same route with your next car! So anyway, that’s that, that’s how the M3 looked. I’ll definitely miss it, it was brilliant in standard form but even better modified just a little. Where’s the fun in leaving a car standard after all? And I know what you’re all thinking, what’s going to happen to the M5 when it comes? Well, to be honest, I’m not sure. All I can say is I’ll see how it goes…
It’s the end of the road for Tom’s #BMW-M3-F80 . Three-piece #CSF-cooling-kit made a big difference M3 looked fantastic on the 763M wheels. Sexy interior carbon pack. #BBK the best mod Tom did.
Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationMARK B’S E30 M3 #BMW-E30 / #BMW-M3 / #BMW-M3-E30 / #BMW-3-Series / #BMW-3-Series-E30 / #BMW / #BMW-S14 / #resto-mod /
There are some events that simply stand head and shoulders above the rest and the Retro Rides Gathering is one of them. Despite a few location changes over the years, it continues to be the class of the field as far as I am concerned. This year saw a multitude of cars descend upon Shelsey Walsh where, set in the hills of Worcestershire, is one of the UK’s premier hill climb tracks. Established in 1905 it has seen a glorious array of cars and drivers, stopping only for the two world wars. I had been before, so knew what to expect and although this was very much a ‘for fun’ event, it doesn’t stop you trying once the light goes green.
In the days before Retro Rides I was able to get Joe Geach of ARM BMW and Motorsport to spanner check the car and change the oil. I had already backed off the KW suspension to full soft, so as to afford as much compliance as possible. It’s still very firm but allows for some roll and better grip on the slower, tighter corners. In the quick stuff the M3 still felt totally planted and gave me loads of confidence to push on. Now, I’m no natural talent and certainly haven’t missed out on a career in the BTCC or DTM, but I’ve driven a fair few race cars (including an outing in a Formula Opel Euroseries car. A genuine slicks and wings formula) and my personal best in a race-prepared E30 325i is a 59.7. Now considering I’m built for comfort and not speed, I was pretty happy with that.
I usually leave Cornwall at 3am and make my way up to Shelsey, but this time I went all posh and got myself an Air BnB in Hereford. This meant I could have a lie-in till 7am, grab a shower and enjoy some of the beautiful roads that area has to offer. I’d driven up the day before and crossed the Severn Bridge for some B road fun en route. I even managed to find a jet wash close to Shelsey and got the M3 pretty clean considering the 250+ miles I’d covered and beat the queues to boot. Driving from Hereford to Shelsey, with the sun shining, windows down and the S14 singing, is a cracking start to any Sunday, let alone one with the Gathering to follow.
One of the great things about Retro Rides is the eclectic mix of cars, with nothing newer than 1995. It really doesn’t matter what you drive so long as it’s old enough, and the atmosphere is terrific. On a personal note, I’m always made to feel so very welcome and it’s a real pleasure seeing the many familiar faces year-on-year. It’s that which keeps me going back time and again.
As those of you who read my ramblings will know, it has been a tough year or so with my M3. It seemed that every time I left Cornwall the engine would let me down, and not in a small way. Much as I love the S14, it is extremely expensive to rebuild and I’ve been chasing reliability issues for months now. The biggest problem has been with the bearings and the supply of OE quality from independent suppliers. Hopefully, it appears to have been third time lucky and the M3 is now running better than it ever it has. Even with some of the hottest ambient temperatures of 2018, power was a strong 250hp+ on ARM’s dyno, with the rev limit set at 8.5k for engine longevity. It sounds absolutely glorious, especially now there are a few miles on the Eisenmann/Supersprint exhaust system. The pops and crackles on overrun are epic and, along with the induction noise from the carbon air box, it almost sounds like a proper DTM car.
The mix of cars at Shelsey included a selection of Bavaria’s finest, including a ’60s 1600-2 with a supercharged M42 that was owned and built by James of JFi Classics in Brecon. There was also an S54-powered E28 flying up the hill and sounding glorious. Very much a home-brewed M5 and one of my personal favourites of the day.
As well as having fun on the hill at Shelsey Walsh, I have been working with Thomas Garner Films and Mumbo Vlogs, who were shooting on behalf of Petrolicious. I’m going to hazard a guess that if you’re reading this, you’ll know Petrolicious and the content they put out on YouTube. If you don’t, you’re in for a real treat. The video will be up in October so just search for ‘Petrolicious BMW E30 M3,’ sit back and enjoy. You’ll also find relevant content on Instagram at mark_e30m3 and official-mumbo.
Finally, if you’re in Cornwall around mid September, be sure to pay a visit to Watergate Bay and see what is billed as being the UK’s first closed road speed event. It takes place over the weekend of the 15/16th September 2018 and you’ll see a brace of E30 M3s being driven as they were designed to be. There are some very special cars and drivers entered so check out www.watergatebayhillclimb.co.uk for further information. Feel free to come say hello if you visit the pits too! If you can’t make it, I’ll try and bring you an in depth report after the event.
E30 looked the part at Shelsey Walsh. BMW M3 E30 will be a YouTube star very soon. M3 received plenty of attention.Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationOUR CARS MARK B’S E30 M3
/ #BMW-E30 / #BMW-M3 / #BMW-M3-E30 / #BMW-3-Series / #BMW-3-Series-E30 / #BMW / #BMW-S14 / #resto-mod /
As I write this, last week was the first Retro Rides Gathering at Goodwood and a date I had marked in my diary a good few months back. The chaps at Retro Rides always put on a good show, with their August events at Shelsey Walsh being just about my favourite of the year. Goodwood was a first, though, and with a combination of static show and track action it was also going to be popular. There was also bound to be a good selection of classic BMWs, with many having a resto-mod flavour.
Personally though, I was looking forward to getting my E30 M3 out on track and enjoying all the hard work done over the past year or so. Living in Cornwall is lovely but the only real downside is everywhere being so far away. I could have camped at Goodwood but opted to use Airbnb and find myself a place to stay close by instead. Before leaving, though, I figured I would get local valeters iShine to come work their magic and get the M3 looking its best. Much as I love my car, detailing just isn’t my thing! I also did a thorough spanner and fluid check to make certain all was as it should be, before loading my suitcase and crash helmet, then heading off towards Goodwood. In fact, it was Chichester I was staying at and the journey up couldn’t have been better. The weather was absolutely gorgeous and the M3 was in its element on the twisting A roads of Cornwall, Devon and Dorset. Being so warm, as I headed through the New Forest I opened the windows and enjoyed the induction noise, with pops and bangs from the exhaust on overrun. It had to rank as one of the best journeys I’ve done in the M3. I arrived at the #B&B in good time and was up early on Saturday, getting petrol en route to the circuit, with the sun still shining.
Goodwood is a fantastic circuit. It’s fast and flowing, with some double-apex right-handers that really suit the E30 M3. The warm ambient temperature also meant the Nankang AR-1 tyres were at their best and I was looking forward to putting them through their paces. I knew they were good from using them on the street but that simply doesn’t compare to lapping a circuit. On a track day I would have dropped cold air pressures to around 20 psi but this was a sprint format that consisted of a standing start from the pit lane and two flying laps. There was also a second chicane that had been added to the back straight, in an effort to slow things down a little. There were morning and afternoon sessions, with 40 cars in each that were divided into groups of five. Cars were released one at a time, with about 15 seconds between them, so as to spread the cars out on track. Overtaking was also forbidden. The track action was always going to be about fun rather than competition with such an eclectic group of cars anyway. I had a Studebaker ahead of me and a ’60s Ford Galaxy behind, so you see what I mean.
My first two laps were more about remembering the corners than pushing the limits of the car. Even so, it wasn’t long before I found myself riding the rear of the Studebaker. I backed off, enjoyed the views and once the gap had grown again, nailed the accelerator, enjoying the sound of the S14 revving up toward its redline. I know I’m biased but it sounded glorious. In the past I have always tried to short-shift the gears and get the M3 settled into the corners, carrying as much speed as I can.
I must say I was incredibly happy with the performance of the #Nankang-AR-1 tyres. The levels of grip were excellent right from the off and they were certainly consistent. My first introduction to Nankang was of a cheap tyre most often used by drifters and, if honest, there was a bit of a stigma attached to the name. It is pretty clear that Nankang have done some serious development and, as a control tyre for the #M3 cup, the general consensus was it’s a very good tyre indeed. It will be interesting to see how well they last, when compared to the likes of the Toyo R888R, but their performance is certainly next level. Yes, they’re not exactly ideal in wet weather but they were never meant to be. It’s hard to see how you could get a better track day tyre for the money, though. The only negative being there isn’t quite the choice in sizes I would like, but hopefully that may change in the future? Anyway, big thanks to Ben Lawson at Nankang UK.
The M3 runs KW Competition suspension and it felt so planted, really giving me the confidence to carry so much speed through the corners. My previous experience had been with my old #BMW-325i-Coupe-E30 race car but the M3 is in a whole other league. As I passed the chequered flag I was able to scroll through the various readings on the Stack dash display and everything was well within the limits so we rolled around to the paddock and awaited our next laps.
Whilst sat in the paddock we shuffled our group of five cars around, with the M3 going first as it was the fastest. Now I could really push on without catching slower traffic, although I was also mindful of this being fun and not competitive. As we had a few minutes I was able to take a look at some of the other cars and especially the other BMWs. How about a 1970 1600-2? I love ’02s anyway, but this one belonged to James of JFi Classics in Brecon. James and I have been friends for a few years now and he has put together some terrific cars. This ’02 has a real sting in the tail, with a supercharged #M42 under the bonnet. The registration plate FLY is pretty apt and the whine of the supercharger is phenomenal. There was also another E30 M3, but rather than being powered by an S14 it has what was the first #LS1-V8 conversion. Power is around 450hp so it was always going to be quick. My personal favourite is a car I have known since I first discovered BMWs 30 plus years ago! It’s a 2002 Touring but with M30 3.5 power and triple Weber carbs. It has to be said, this is just about my perfect ’02 specification and a credit to Ian Elliott who has built and developed it over many years.
As time came around for my next laps, James from JFi’s son jumped in as a passenger, having never ridden in an E30 M3 before. Obviously with such a valuable cargo I wasn’t going to go 10/10ths but after the first lap we were both enjoying the performance of the M3 and all those clichés that have been written for the past 30+ years. The second lap was certainly my quickest of the day, carrying more speed through Woodcote and braking hard for the right, left of Chicane as we entered the pit straight and crossed the finishing line. It was as we passed that line the dash warning light flashed and the Stack display showed ‘Low Oil Pressure!’ accompanied by the unmistakable sound of bearing knocking. I immediately killed the engine and coasted to a halt. My weekend had just taken a nosedive.
The next half hour was mainly spent staring in disbelief. I had done everything I could to guard against this scenario yet here I was, looking at yet another incredibly expensive engine rebuild. What I just couldn’t understand, though, was why? The reason I had installed the digital dash display from Stack Ltd, was that it allowed me to keep a close eye on exactly what goes on with the engine. The custom rad, larger oil cooler and baffled sump were also fitted to allow the S14 to be used as it was designed to be, on track. I’ve been almost obsessive in keeping watch over fluid levels and temperatures yet here I was with another engine failure. As you can imagine, my enthusiasm for the rest of the weekend took quite a knock so I opted to get the M3 transported back home so that ARM could get the engine out and back to the builder.
A could of days later Joe at ARM took off the sump and it was soon clear that cylinder number one’s big end shell had spun. Added to that, the rest of the bearings look to have worn prematurely and you’d never believe this was an engine that had run for just 300 hours. What we couldn’t see though, was a reason to explain the failure and without that I couldn’t rebuild and gamble that it could happen again.
The next couple of days saw me calling and emailing anyone with experience of using BMWs S14 in competition. They all agreed that I appeared to have taken pretty much every precaution and both the ECU and Stack memories confirmed that there were no excessive coolant or oil temperatures, the engine had never been over-revved and the only thing that was shown was a momentary (and pretty catastrophic) loss of oil pressure. It was then that I mentioned that the crank had been subjected to a +0.75 regrind and it is this that seems most likely to have been behind the failure, due to its removing the nitriding that gives the crank strength. In fact a few people have since told me that they just wouldn’t regrind an S14 crankshaft at all, let alone as much as +0.75 and that I need a new crankshaft before I rebuild my engine once again. I also need to replace at least one of the Arrow con rods as the end cap has blued from the heat generated by the spun shell. Thankfully Russ, at JC Racing in Thirsk, has come to the rescue. So there we go. As it stands today (and things may well change between now and your reading this) I have a pretty expensive parts list to fill. I had no idea that the S14 crank couldn’t be reground but as they say, every day is a school day and this was an expensive lesson!
BIG THANKS TO Joe at ARM BMW, Kirby at C3 BMW Russ at JC Racing, James at JFi Classics Nigel at Moseley Motorsport I also owe a huge amount to my long-suffering partner Claire. I think it’s fair to say she hates the M3 and would rather I sold it and took up knitting instead
Nankang AR-1s impressed on track. The M3 was treated to a detailing session. Compbrake #BBK great on track. #BMW-E30-LS1 #V8-swapped-BMW-M3-E30 was also on track.Stream item published successfully. Item will now be visible on your stream.
- Post is under moderation
Classic exhaust for #BMW-E36 / #BMW / #BMW-M3 / #BMW-3-Series / #BMW-3-Series-E36 / #BMW-M3-E36 / #Milltek / #Milltek-Classic-Exhaust-System / #Exhaust-System
Milltek has released detailed specs on its Classic system for the E36 M3, in both 3.0 and 3.2 guises. These exhausts will fit coupé, cabriolet and saloon models and Milltek also offers system solutions for both the E36 325i and 328i models in the same range.
The Milltek Classic range for the E36 offers a solution from the downpipe back, bringing aesthetic improvements and power gains along the way.
A hi-flow catalyst bypass pipe reduces mass by a useful 9.15kg, delivering a helpful performance increase plus an improvement in throttle response.
Manufactured at Milltek Sport’s own UK factory entirely from #Type-304 stainless steel, the Classic’s cat bypass pipes have been designed primarily for track day or race use, and for markets which don’t require the fitment of catalysts under emission laws. Removing the catalysts will offer the best possible flow rates, although a remap may also be required in some cases.
The rest of the system is also made from Type-304 aircraft-grade stainless steel, and features high-flow, mandrel-bent pipework, Each one is gas-flow tested to ensure maximum performance throughout the rev-range, and offers a sonorous straight-six exhaust note.
The finishing touch to this system is the back-box, which can be fitted to either the #Milltek-Classic system, or indeed, in isolation to an OEM front-half, for those enthusiasts looking for an improvement in looks and sound at a cost-effective price. The systems for the 325i and 328i are very similar in design, but offered as half rear systems only. Prices start from £495.97 + VAT (325i/328i half system) and, for more information, visit: www.milltekclassic.com
The new #Milltek-Classic-exhaust-system exhaust system offers options to fit #BMW-325i-E36 and #BMW-328i-E36 models, as well as the M3.
Classic rear silencers and cat-replacement silencers for the E36, from Milltek.Stream item published successfully. Item will now be visible on your stream.
- Post is under moderationCAR: #BMW-E46 / #BMW-M3 / #BMW-M3-E46 / #BMW-E46 / #BMW-M3 / #BMW-M3-E46 / #BMW-3-Series / #BMW-3-Series-E46 / #BMW-3-Series-Coupe / #BMW-3-Series-Coupe-E46 / #BMW-M3-Coupe / #BMW-M3-Coupe-E46
MILEAGE THIS MONTH: 156
TOTAL MILEAGE: 87,276
MPG THIS MONTH: 26.9
TOTAL COST: £167 (tyres & locking nuts)
Clubsport? Lightweight? Race car? Well, not quite; but sitting inside, the M3 does have the look of a car midprep for an attack on a Nürburgring laptime. A couple of delays mean the M3’s interior is still missing a fair proportion of its trim, but the guys at Perfect Coating (www.facebook.com/ perfectcoating) will have that sorted by the next update, so I’m looking forward to photographing the interior in its shiny new glory in time for next month. Talking of next month, with good weather on the cards and some events in the calendar I’m planning to take the M3 to Wales with some mates, and if things work out just-so, a sojourn to the Nürburgring too. Throw in another visit to Bruntingthorpe for VMAX and I’ll have a chance to put some good quality bonding miles on the M3. Truth is, I’ve not used it as much as I’d like of late which may be good for the mileage (a relatively low 87k considering the 2002 year of registration) but this is not a car to be afraid of using – you only need to look at the amount of M3s deep into six figure mileages to know that if well looked after, there is nothing to fear. With the service indicator telling me I have 800 miles left before the next service, she’ll be well looked after very soon, most likely by Highams Park Motor Company in East London.
It’s the perfect time for some routine maintenance, meaning I can look forward to summer fun with her! That’s not say I’ve not had fun in the dark months, and now I’ve had a chance to put some proper miles on the M3 with the 18-inch wheels I’ve really grown to love them. Unsurprisingly, after last month’s sideways fun the rear tyres were looking rather sorry for themselves. Lucky for me, my local tyre shop happened to have a pair of very lightly used correctly sized Pirelli P Zeros in stock; an absolute bargain for £150, and I had some new locking wheel nuts fitted at the same time. The old lockers were looking pretty sorry for themselves, and I had visions of being stranded with a flat, unable to change wheels due to a rounded off key. It’s a small thing, but it gives peace of mind. As I reported last month, initial impressions on the smaller wheels were a marginal trade off in ultimate grip in return for better ride quality and even more benign, playful handling characteristics when pushing on.
With the new Pirellis, a good run on some of my favourite local B roads cemented that impression. I’ve never been one for chasing ultimate grip anyway – I’m not setting lap times – so I’d rather have a car which has grip levels well matched to the power output, with really enjoyable handling which can be exploited at sensible speeds. On the 18-inch wheels, the M3 delivers this by the bucket load. I’ve grown to love the look on the dark grey smaller wheels too; the polished 19-inch wheels always looking a bit bling for my taste.
Despite sharing space with cars worth 50+ times what I paid for the M3, it still managed to turn heads and secure a prime spot at a local breakfast club meet. If you’re an Essex dweller, I’d heartily recommend a trip down to The Hare near Roxwell the first Saturday of most summer months (check its calendar to be sure). Get there early enough and there’s even free coffee. But more importantly an excellent mix of old, new, and sometimes hugely rare and valuable cars to have a look at… and a 15 year old M3 with half the interior missing. It was my morning jaunt to the last meet that gave me the chance to enjoy my favourite local roads, and driving back I was feeling pretty pleased with life. I think it’s fair to say my love affair with the M3 is going pretty strong…Stream item published successfully. Item will now be visible on your stream.
- Post is under moderation/ #BMW-Art-Cars / #BMW-Art-Car / #BMW / #Art-Cars / #BMW-M3-GT2 / #BMW-M3-GT2-E92 / #BMW-M3-E92 / #BMW-M3 / #BMW-E92 / #BMW / #BMW-M3-GT2-Jeff-Koons / #BMW-M3-GT2-Jeff-Koons-E92 / #Jeff-Koons / #2010 / #BMW-M3-GT2-Art-Car / #BMW-M3-GT2-Art-Car-E92 / #BMW-3-Series / #BMW-3-Series-E92
For its 17th Art Car BMW really went back to where it all started and entered an M3 GT2 at Le Mans complete with Jeff Koons’ arresting livery
The first three BMW Art Cars all cut their teeth at Le Mans and for the 17th Art Car BMW returned to the track in 2010 with the E92 M3 GT2. It had high hopes for the car as it arrived on the back of a win at the 2010 Nürburgring 24 Hour race and to ensure there was plenty of interest in BMW’s first return to La Sarthe BMW decided to commission Jeff Koons to add his quirky style to the car.
It was officially unveiled at the Pompidou Centre in Paris with a suitable level of razzmatazz and while the car might have been generating plenty of interest off the track it wasn’t quite so impressive on it. Two M3 GT2s were entered, one in the traditional BMW livery (number 78) and the Koons’ Art Car, number 79, its number chosen as a tribute to the Warhol M1 that had raced at Le Mans ‘79. At the qualifying event the two BMWs came sixth (78) and 11th (79) in class.
Jeff Koons, is one of the most celebrated artists of our time, and was born in York, Pennsylvania, in 1955. Koons’ work has been exhibited internationally and is in numerous public collections, including the Museum of Modern Art in New York, the Whitney Museum of American, the Guggenheim Museum (both in New York) and The National Gallery in Washington, DC.
As part of his creative process, the artist collected images of race cars, related graphics, vibrant colours, speed and explosions. The resulting artwork of bright colours conceived by Koons is evocative of power, motion and bursting energy. With its silver interior along with the powerful exterior design, the Art Car imparts a dynamic appearance even when it’s standing still. “These race cars are like life, they are powerful and there is a lot of energy,” said Koons. “You can participate with it, add to it and let yourself transcend with its energy. There is a lot of power under that hood and I want to let my ideas transcend with the car – it’s really to connect with that power.”
In the event the Art Car didn’t have a great race, making contact with another competitor and having several mechanical maladies. The final ignominy came as Andy Priaulx approached the Indianapolis curve at around the five hour mark when the M3 ran out of fuel – either the consumption was higher than expected or not enough fuel had been added at the previous pit stop. Either way, the car’s race was done. The number 78 car battled on to the end, eventually finishing sixth in class.Stream item published successfully. Item will now be visible on your stream.