Details
VW Beetle Classic Club More
Blogs in Group
    No posts created yet.
Link copied to your clipboard
Items tagged with #VW-Beetle
Pinned Items
Recent Activities
  •   Russ Smith reacted to this post about 1 year ago
    CAR #VW-Beetle / #VW / #Volkswagen-Beetle / #Volkswagen / #Volkswagen-Beetle-MkI

    RUN BY Martin Port
    OWNED SINCE March 2011
    PREVIOUS REPORT May 2017

    Some cars just don’t get the love they deserve, and I’m embarrassed to admit that the Beetle is definitely one of them. It has given reliable service for years now and, despite my many promises to carry out major work, I’ve failed to deliver. Even worse, it took the failure of the MoT test to propel me into action, and even then it was at the pace of an anaesthetised sloth.

    What did it fail on? Surprisingly, it was really ‘only’ some rust (and a broken anti-roll-bar clamp). I’d seen much worse, but its proximity to the rear suspension mounts meant that it was an immediate ‘x’ in the box. So, the Beetle was back in the garage while I examined the options for repair. Since this coincided with winter’s first dusting of grit on the roads, I deliberately didn’t hurry – though it’s too late to take evasive action, of course.

    Eventually, once I’d cut out the rot, my brother-in-law Pat crafted some repair sections and we set to work. Between us we welded in the fix, which was a tricky under-seat corner piece, but while I was inspecting inside the wheelarch I noticed some more rust.

    I cleaned up and welded in a couple more off-cuts of steel from Pat’s workshop, and applied seam-sealer to the inner repair. That meant I now had to underseal the inner arch, which I knew desperately needed doing to the entire underside. Fortunately, it’s still in remarkably solid condition.

    I’ve used Dinitrol before and found it to be very effective, so opted for the same again this time. Without a compressor rigged up at home currently, I plumped for several 500ml cans of its 4941 aerosol because I knew it would be fairly simple to apply where needed. Getting the Beetle up in the air was easy thanks to my old set of ramps and large axle stands, offering just enough clearance for a good wire-brushing of the underside.

    Then it was time to put the Dinitrol to good use and slowly apply it to the underneath of the vehicle and into the wheelarches. An hour later I was very pleased with how the floorpans looked. Compared to using a schutz gun in a confined space, the aerosol allows you to get into all the smaller areas with ease – perfect if you don’t have access to a four-post lift.

    With the welding done I sent my spare set of period wheel rims to Berkshire-based company Procoat to be blasted, primed and powdercoated.

    A five-minute chat with the owner turned into an hour as his enthusiasm for classics became obvious, having been given the name Aston Martin by a father with a clear sense of humour. It’s little wonder that not only does he now run a company that specialises in blasting and coating car parts, but he also owns several Astons.

    Having heard him wax lyrical about what makes a good process and the importance of how many microns of coating you need on a rim, it was nice to see the fruits of his expertise when I collected the finished wheels. The gloss black is fantastic, and the finish almost mirror-like – the colour isn’t standard, but our choice for the Beetle.

    We had agreed to help Vintage Tyres out by evaluating some whitewall rubber, so these were fitted, and suddenly the combination of new tyres and shiny rims put the rest of the car to shame.

    It might be back on the road, but it looks as if the bodywork and a respray have to be the next steps.

    THANKS TO
    Procoat: 01635 200017; www.professionalcoatings.co.uk
    Dinitrol: www.dinitroldirect.com

    Whitewalls always provoke a ‘Marmite’ response, but even if they stay on just for the summer, they certainly look the part when coupled with the freshly painted rims.

    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Antonio Ghini reacted to this post about 3 years ago
    Car #VW-Beetle / #VW / #Volkswagen-Beetle / #Volkswagen / #Volkswagen-Beetle-MkI
    Run by Martin Port
    Owned since March 2011
    Total mileage 87,698
    Miles since February report 1053
    Latest costs £137

    SERVICE TIME FOR MISFIRING BUG

    The Beetle had been doing what was asked of it for some time without any purposeful maintenance, so it came as no surprise when it suddenly developed a misfire one day without warning. A cursory look failed to throw up anything obvious, so I figured that it was time to carry out a full service and see if that resulted in an improvement.

    VW Heritage markets a kit that includes plugs, leads, distributor cap and rotor arm (the car is already running a points-less ignition system), but I knew that I also needed to check the valve clearances, and that was a slight issue.

    With no replacement for the C&SC workshop in sight, my own garage out of action thanks to ongoing construction work, and the driveway full of building materials, I was faced with carrying out the service at the side of the road.

    I’m no stranger to kerbside maintenance but, with a wet winter in full swing, the thought of having to check the clearances while lying in the gutter didn’t appeal much. I was always going to be tempted by an offer from friend and Our classics regular Oli Cottrell to do the job in exchange for a few notes!

    When he delivered the car back to me, he was full of praise for how it drove – an assessment that I was pleased with, given that he worked for a time at a classic VW specialist. As suspected, the valve clearances were out and one had closed up, but with everything adjusted the Beetle was full of pep once more… until the following day, when a text from Mrs P read: “Fine going into town, but stuttered all the way back.”

    Sorting a loose ignition lead helped a little, but we also decided to look at the carburettor settings. The manual suggests that the volume control screw needs to be somewhere between two-and-a-half and three turns out, but this one was at six, which would explain the black electrodes on the new plugs. After a road test, we settled on three turns and, with a tweak to the air bypass, normal service was resumed.

    Typically, with the Beetle ousted from its cosy garage, the cold snap took its toll and killed the battery. That was easily sorted with a visit to the auto factor, but outdoor living is also proving detrimental to the chrome. That is disappointing, because it isn’t even a couple of years old – raising the issue of quality when it comes to parts. With that in mind, when the wash/wipe switch appeared to fail, I was about to order an OEM replacement, but decided to check the rest of the system first. It turned out that the switch was fine and that the upper pipework and nozzle were gummed up.

    After dismantling the whole assembly from the water tank upwards and repeatedly sucking out all the muck, the washers function again – but in the process I had succeeded in drowning the adjacent radio. It now only partially works, and out of only one speaker. I’ve never been particularly enamoured with this unit, though, so plans are afoot to conceal an alternative in the glovebox and reinstate the dashboard blanking plate.

    With the underbonnet area emptied to attend to the washers, I noticed that the pipe from the fresh air box had disintegrated. This is meant to enable water to drain out, helping to reduce condensation on the windscreen. If, however, the pipe is absent or broken, water just collects in a pool above the fuel tank and will quickly corrode the metal. A new one was bought for £11 and so this is at least one part of the bodywork that won’t be disappearing anytime soon.

    THANKS TO Oli Cottrell: 0118 971 2091 / #VW-Heritage : 01273 444000; www.vwheritage.com


    Not a Californian sunset, but sunrise over a multistorey in Twickenham. Inset: replacement air box drain tube will help to prevent corrosion.

    Air box removed to access washer system Recent chrome already attacked by rust. Pipes and jets were thick with black gunk. Oli doing his best James Herriot impression while attempting to solve the ongoing misfire.
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Martin reacted to this post about 3 years ago
    We Europeans have a pretty exact imagination in regards to the american automotive lifestyle. A home in a friendly housing estate, wide driveway including a big garage and probably one or two palm trees around. Exactly what we got when we followed an invitation from the .Busted Knuckle Garage' to Garden Grove CA. 3 crawlies were frolicking around the driveway entrance and when we were asked about which we would shoot, we chose all of them. Like a scene from a movie we cruised across Orange County and picked up plenty of looks and appreciation along the way.

    / #1967 / #Volkswagen-Kafer / #Volkswagen / #VW-Beetle / #Volkswagen-Beetle / #Volkswagen / #VW / #Volkswagen-Beetle-MkI / VW /

    We don't know if the .Busted Knuckle Garage' boys forget to press the suspension's ,up button' every time they go for a drive, but when we were there we really just scraped towards our photo location, a large warehouse area, well aged like our subjects. Positions were quickly found and on Nick Ramirez', 67 Bug, the 9" wide steelies pressed themselves well towards the fenders. That these look a little worn is not a work in progress but exactly what he wanted. Similar to all the details - partially original parts from good old Germany - this mirrors the style that Nick wanted to achieve.
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Martin reacted to this post about 3 years ago


    JUST BUGGIN’ Late-spec air-cooled Beetle gets left-field makeover we canʼt get enough of

    MAX HARDCORE

    Max Edward’s late-model Beetle, running uncharacteristic wheels, may be frowned upon by the air-cooled fraternity but we just love it. What do you think? Words: Elliott Roberts. Photos: Ade Brannan.

    We don’t tend to feature many air-cooled Dubs in the pages of Performance VW. Now that’s not because we don’t like them you understand. Far from it. It’s more the fact that there are already plenty of other publications around specialising in non-water pumpers. That’s not to say we won’t run them in the mag though. Every now and again something ‘air cooled’ turns up that’s just so off the wall that we can’t resist the urge.

    In fact, there have been a few instances of late where that’s happened. It’s actually been like the early days of PVW when we specifically highlighted one air-cooled Dub per issue. Only last month we featured Richard Jones’ stunning Type 34 Karmann Ghia (albeit it with a 13B rotary motor out back) from Las Vegas. Then, back in the January issue, it was the turn of Jo Riley and his custom ’1972 Karmann Ghia (this one running an MR2 turbo engine). It doesn’t stop there either, because the month prior to that we brought you news of a car we’d been chasing for quite some time: the electric-powered ‘Black Current’ drag racing Beetle. Like we said, it’s only the ‘out there’ cars that really appeal and while Max Edwards, owner of the creation on this very page, has retained an air-cooled motor, his Bug is anything but conventional.

    Okay, so we admit, it was the wheels that initially drew us to Max’s ’1978 Beetle, but we soon discovered the car as a whole has been built with a slightly different approach. “Cars have always been a big part of my life for as long as I can remember,” he says. “My dad had air-cooled Dubs in the ’80s. That’s when we started to go to shows and I fell in love with VWs and, more specifically, Bugs.” Amazingly, at the tender age of just 22, Max doesn’t only own this Beetle but also his own restoration business, called EVA VW Retro. “We specialise in air-cooled and early water-cooled VWs mainly.”

    Although he’s owned more air-cooled Dubs than anything else, Max admits he prefers the approach to building a water-cooled show car.

    “I find the air-cooled scene incredibly samey,” he reveals. Perhaps that’s why we are so fond of his Beetle, he’s put a water-cooled spin on it! “There are just so many people running the same tried and tested looks and not doing anything different. The water-cooled scene always struck me as being a bit more experimental, so I wanted to take some of this and apply it to my air-cooled car.”

    He may be in his early twenties but Max has already had 11 cars so far. From Type 3s, a couple of E30 Beemers, and even a Porsche 924, he’s had the lot, but the Beetle was his first car at the tender age of 16. Did he ever expect it to get this out of hand, though? “The car was shiny and solid but neglected when I bought it. It had been repainted in its original silver but nothing else has been done.” According to Max it began life as a ‘Last Edition’ 1200L and it still has a numbered plaque inside that ranks it at number 213 of 300 of the last ever Beetles sold in the UK.

    “I couldn’t afford an early car back then, but this was pretty solid, just needing small bits doing that, at 16-years-old, I could fix myself. If I had an early car then I probably wouldn’t have ended up going this far with it.” Apparently the car’s been through a number of different looks along the way and despite his plan to lower it and just do the odd bit here and there, Max never envisaged a full restoration with a colour change and a set of wheels that cost the same as buying the car in the first place!

    So what style, if any, influenced him? “I’ve always liked the ‘German-look’, which usually features Porsche parts and engineering on fast road and track Beetles.” Max was obviously heavily influenced by the whole stance movement, too: “The car has always had a bit of Porsche flavour to it I guess. In fact, the BBS RSs are actually spec’d for a 930 Turbo with wider rears and relatively skinny fronts, giving it the perfect stance.” We’re getting a bit ahead of ourselves though, so let’s rewind a bit.

    The first thing Max did when he got the car was sort out the interior. “When I bought the car it looked like a bear had been living in it, so I fitted replacement OE seat covers, prior to the 964 Tombstones going in.” Having done his thing with the car for a couple of years, it was actually the summer of 2013 that the it came off the road for the mother of all strip downs. “It was pretty tough taking my lovely, dependable Beetle off the road and stripping it down to nothing more than a bare shell, chassis, and a box of bits. It wasn’t the build that was hard part but more being unable to drive the thing,” he says.

    Apparently most people thought he was mad taking the car off the road but he knew that behind the tidy façade there were some nasty areas that would soon be exposed, so he decided to get in there first. “The car had a fair bit of rust repair welding done, requiring some small panels and localised repairs,” he explains. In the end the chassis had brand-new pan halves, too, with everything being blasted and either painted or powdercoated during the rebuild. It was truly like a brand-new car when it hit the road again. When it came to paint, Max fancied white – not just some factory shade, though, but RAL 400 white. “None of the VW whites were white enough,” he says, “but I now know why manufacturers don’t paint their cars pure white as I practically need to wear sunglasses now every time I wash it.”


    When it comes to chassis mods, Max claims the car is mainly stock, with a few ‘enhancing’ modifications: “The front end is narrowed 2” to allow for the aggressive fitment and runs long travel ball joints, dropped spindles and strengthened shock towers.” Sounds quite serious to us! Out back Max choose to go down the IRS route: “There are a lot of Beetles dropped dirty-nasty low on standard swing-arm suspension but it just doesn’t perform too well. Mine uses semi-trailing arms and CV-jointed driveshafts. It drives as good low as it does at standard ride height, without the crazy camber, too.” Max claims the rear end had to be notched a fair bit but he’s so happy with the way it looks and drives. “I went for air-ride as well, as I wanted it a lot lower but without compromising the way it drove. It was just way too soft static and used to bottom-out all the time.”

    Max claims the wheels are one of his favourite parts of the car: “I know RSs are a bit played-out on the water-cooled scene and yet they’re almost unheard of in air-cooled circles.” He had considered doing Autostradta Modenas but is pleased he went with the RSs and being direct fit, they couldn’t be any better. “I really, really didn’t have the money for the wheels at the time but I just had to have them,” he reveals.

    “I struggled money-wise for a while but don’t regret them one bit.”

    If anything, Max wishes he’d done a bit more to the bodywork, which is still very much stock (other than the graphics) but we reckon it looks perfect as it is. Okay, we’re obviously massive fans of the look but how has the car been received on the air-cooled scene? “It’s been a bit of a mix, with some people not even noticing it at all and then others just totally getting it,” Max tells us. He reckons the air-cooled scene is very set in its way and if it’s not an early-type car, done the right way, on the right wheels, then it just won’t get a look in. “They probably look at mine and wonder why I’m running Mk1 Golf wheels. It’s one of those cars you either get or you don’t, I guess,” he grins.

    When it comes to the motor, Max is running a 1641cc lump with an Engle 110 cam, straight- cut gears, all high-rev valve gear, 1.25:1 ratio rockers, a pair of Solex Kadron carbs, and a Vintagespeed stainless exhaust. The engine runs on electronic ignition with a custom breather box setup, MST serpentine pulley kit with all-gold tinware and powdercoated black auxiliaries. “It all runs through a Freeway Flyer gearbox with a longer fourth and final drive. I’ve had the car into triple figures a few times and it just keeps on pulling,” Max smiles.

    It hasn’t all been plain sailing, though. “The car’s been super reliable, always starts and runs great. There was this one time, though. We were on the way to our local meet, gunning it down the motorway at a fair pace, when all of a sudden there was a big plume of white smoke out the back,” Max says. He killed the engine and coasted to the hard shoulder. Turns out the main oil line for the remote filter on the exhaust had melted. “As I didn’t have any more oil line with me we had to wait for a recovery vehicle, but that just gave us chance to air it out and take a couple of ‘scene’ photos for social media,” he laughs. We like the fact Max doesn’t take himself or the car too seriously. Max is the first to admit he never set out to get attention. “I’m honestly so chuffed when people do get it. I never expected a magazine like PVW to be interested in my air-cooled car. I’m still as in love with the car now as I was when I drove it daily at 17.”

    As for the future, well, Max has already retrimmed the interior since our shoot with Porsche Pasha pattern and half leather seats and doorcards, plus a trimmed boot build along with Alcantara headliner and a new air controller. This year he just intends to enjoy the car for now, but when it does start looking a little tired then it will get torn down and the colour changed, as he explains: “I’ll probably go for some super-deep Nutmeg brown metallic or maybe even classic Porsche Guards red.” It sounds like Max has put some thought into this already. “I certainly never plan to sell the car. I’d like to make it properly fast one day too,” he adds. We’ll just have to watch this space. This is certainly not the last we’ve heard of Max or his Beetle for that matter.


    You can’t beat a Bug for mod-cos, you know, like a steering wheel, seats, erm…
    “I’ve had the car into triple figures a few times and it just keeps on pulling”
    “The water-cooled scene always struck me as being a bit more experimental, so I wanted to apply this to my air-cooled car”

    Dub Details #1978 / #Volkswagen-Beetle / #VW / #1978-Volkswagen-Beetle / #Volkswagen / #VW-Beetle

    ENGINE: 1641cc four-cylinder with Engle 110 cam, straight cut gears, all high rev valve gear, 1.25:1 ratio rockers, twin #Solex-Kadron carburettors, Vintagespeed stainless steel exhaust, electronic ignition, custom breather box setup, MST serpentine pulley kit and other dress parts, all gold tinware and powdercoated black parts. Freeway Flyer gearbox with longer fourth and final drive

    CHASSIS: Stock VW spine and floorpans, #IRS converted. Six-point braced rear, 2” narrowed front. #Air-Lift suspension all-round

    EXTERIOR: Pure white paint, vinyl stripes, aluminium running boards, body-coloured bumpers, yellow headlight covers, rear window slats

    INTERIOR: Porsche 964 leather front seats, stock basket weave rear, charcoal carpets, cream vinyl headliner, Porsche three- spoke wheel, Auto Meter tach, ‘boot’ build with exposed tank and Air Lift 3P manifold

    SHOUT: My dad for help on the bodywork of the car and other stuff along the way, girlfriend Emma for emotional support and when I’ve needed a hand! Best mate Ed for tons of support and helping out where possible, plus all my other good mates for being the best company ever to do all the shows with!
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Elliott Roberts reacted to this post about 3 years ago
    FEATURE: ELECTRIC CLASSIC CARS

    Jonathan Musk pays a visit to Wales where a new company is converting old classics to electric power and drives a #1965 / #VW-Beetle / #VW / #Volkswagen-Beetle / #VW-Beetle-Electric / #Volkswagen-Beetle-Electric / #Electric-Car / #Volkswagen / #Electric-Classic-Cars

    ELECTRIC CLASSIC CARS / WORDS & PHOTOS: Jonathan Musk / #2016

    I’m in a classic Volkswagen Beetle and it’s raining… in Wales. Surprisingly, the Beetle is powered by an electric motor and is at least twice as powerful as the original car, has a range of 100-miles and has been beautifully restored. I’m driving a classic car, but the experience is strangely modern. There are no fumes, no angry exhaust note and brakes that actually work. It’s definitely classic, but without the usual sensations.

    Driving through the Welsh mountains is a joy to behold in most cars. It’s not about going fast, it’s about travelling well. To enhance the experience, I’m in a classic 1965 Volkswagen Beetle. It’s electric, literally.

    In mid-Wales, Richard Morgan and Graham Swann have started something special. They converts classic cars to electric power and do so with such passion and skill, it’s hard not to be moved by the beauty of their work. I’m paying a visit to Richard, who’s intriguing past is in the world of Rally, where trees and metal meet with the sound of flying gravel and revving engines. Rally is loud, brash and a petrolhead’s idea of heaven. It’s the rugby of the motoring world and, like rugby, rally is a thug’s sport played by gentlemen so it’s perhaps a surprise that Richard has turned his attention to electric vehicles at all. More surprising is that the cars start out as classics.

    Understandably, the key is not to lose the original vehicle’s credibility, sense of nostalgia and classic charm. Electric Classic Cars are not trying to reinvent the original, but rather enhance it with modern tech and for the thrill of creating something new from something old. It’s a careful balance that if done correctly can work astoundingly well, like sweet and sour sauce.

    The non-metallic red 1965 Beetle is a stunning example of professional craftsmanship. The car has been restored to near perfect condition, but crucially without over doing it. It’s been stripped back, enhanced, modified and tinkered with so delicately that initially it’s difficult to tell that it’s an electric car at all, save for the massive advertising sticker in the rear window. If subtlety is an art, Richard has it figured.

    For those familiar with the original Beetle, it was a car that saved the German automotive industry after the Second World War. Rejuvenated by the Allies, the Beetle was seen as a quick way to provide transport through a devastated landscape. Despite an unsettling Nazi past and antiquated 30’s Ferdinand Porsche design, the Beetle next became the darling of the swinging sixties and an ironic icon of the hippie movement. Many were sadly destroyed through lack of care before being recognised as a true motoring icon. Unable to keep up with modern cars even as far back as the 1950’s, the Beetle was never meant to be a performance car. Only when modified as a beach buggy did the Beetle ever truly find performance from its aged flat-four engine. The performance, or lack thereof, didn’t dissuade Hollywood from portraying the Beetle as the star of the ‘Love Bug’ movies. Since then, the Beetle has attracted a huge global following, with people having tried just about everything with, and in, one. There’s hot-rod Beetles powered by massive tuned Porsche engines and even an incredibly powerful electric drag racer, called Black Current.

    The modernising of classics is not entirely unusual and there’s a universal appeal to recreating old classics, as demonstrated by the modern Fiat 500, BMW MINI and even new VW Beetle.
    However, there’s a risk that with each modernisation the classic character is lost and this is the exact opposite of what Richard aims to do with his conversions.

    Instead, each conversion is kept as original as possible to maintain the patina and ownership experience, but without the typical irritations associated with classic ownership; namely grease, smell, noise, discomfort and unreliability.

    Most conversions undertaken are custom orders, so if a customer is on a tight budget Richard won’t look at the bodywork and instead concentrates on the powertrain. For the Beetle, however, it was stripped right back to its bare skin. A fresh coat of striking red paint and a new interior trim later and the car looks factory fresh but it hasn’t lost its aged appeal. Unfortunately, Richard’s the sort of chap who gets stuck into the work so there’s no before-after photo to show.

    Things are kept as straightforward as possible for the mechanicals. Richard has spent many years trialling various electric components to reach the point that he’s happy to sell a conversion to a paying customer.

    Learning what controller works with what motor and charging unit is all a matter of expensive trial and error and invaluable knowledge he’s enviably learnt. So much so that he is now regularly contacted by others for advice, including well-known setups like EV West in America. It’s not all one way though, as if EV West has completed a conversion on a car that Electric Classic Cars’ has not attempted, there’s mutual benefit in sharing expertise.

    Obviously, conversions start with the removal of the oily bits. Engine, exhaust, fuel tank, insulation, oil pipes, cooling paraphernalia etc. are all removed. “The weight saving is significant,” states Richard. He shows me a 1980’s Porsche 911 that’s being stripped down. Interestingly, the assorted items that have been removed weigh nearly as much as the electrical components he plans to install.

    Once the engine has been removed, work begins on planning. Using the original gearbox keeps things simpler and a special conversion plate is fabricated using 3D scanning, geometry and CAD to get it spot on. The conversion plate is milled from a single aluminium block to ensure it is strong, light and accurately machined. The electric motor is then mounted to this and attached to the gearbox, just like the engine it replaces.

    Consequently, the electric motor powers the car through the same gears and clutch as the original car. Each conversion brings its own complications, for example the electrification of brake servos and power steering that would have been powered by the engine. However, the Volkswagen Beetle is a simple machine with no complex electronics or powered anything to worry about, which makes conversion that much simpler and this is part of the appeal in converting a classic. A modern car to electric conversion has much more to consider.


    Once the motor position is sorted, preparation for the power electronics and positioning can begin. Planning is crucial for doing the job properly; there are no half measures here.

    Of course, planning where the components fit is more easily achieved if they’re a known quantity and this is where Richard’s knowledge is really called upon. The most space-sensitive item in any EV is the batteries, which Richard sources from around the globe. Lots come from written-off electric cars, like Tesla that have been rear-ended and this is his preferred battery to work with too. “Nissan Leaf batteries just aren’t powerful enough,” he tells me as he shows me a bank of cells recently repurposed from a Tesla Roadster. High energy density is important for a number of reasons. Firstly, the battery takes up less space in the car and secondly it’s lighter too. This is all the more important in a car that was never designed to take the additional weight of an electric powertrain, let alone its additional power. The original Beetle weighed around 725kg – Richard’s electrified version is around 800kg. The difference is small enough not to have to worry about upgrading the original suspension and brakes.

    However, the original car was barely able to reach 60mph while the electric version can easily get there within ten seconds. Enhanced anchors are therefore wise and this Beetle now sports new disc brakes at the front. Appearance is kept original though, as they’re handily hidden behind the delightfully gleaming chrome hubcaps. Richard’s rally background ensures he’s more than capable at setting a car up properly and this is important as the weight distribution is now near 50/50. Suspension is original apart from the addition of an anti-roll bar to aid handling.

    Most of the batteries are tucked neatly away under the bonnet, but more are to be found hidden under the rear parcel shelf. It’s remarkable to think 22kWh of li-ion cells have somehow been hidden in a car never designed to accept them, when modern car makers still struggle to do the same with a purpose designed vehicle. Even the charge port has been hidden behind the rear number plate that acts as a protective rain flap too. This level of intricate detail and intelligent thinking is repeated throughout the car. The dashboard has been lovingly restored and its clear Richard’s perfectionism has paid off. The one addition that gives the electric game away is a #LinkPRO battery monitor – but even this has been given a chrome dial and slate grey background to match the original speedo it sits beside.

    The level of perfectionism is impressive, but that’s not to say it’s over the top. For instance the steering wheel has a large worn area that only adds to the nostalgia of the car. A fresh one was installed, but Richard felt it was too bright and detracted from the overall classic appeal. Having had a good look around, I was eager to get out on the open road. Would this drive like a Tesla, Jonny’s Flux Capacitor or a classic Beetle?

    Turning the car on is undramatic as the ignition key merely illuminates a small green light LED at the base of the speedometer. It’s alien for a classic car, there’s no vibration, no noise, no smoke, no smell. Ignore the clutch and first, select second and accelerate. It’s that simple. Because the motor isn’t spinning at standstill, the clutch is only needed when on the move. Likewise, there’s little point depressing it when coming to a stop. You can drive the Beetle much like a regular automatic, leaving it in third gear will give a good blend of performance and top speed, but Richard’s discovered second gear is great for humiliating the ever-eager Audi behind. Fourth (top) is good for long runs and motorway cruising, which the Beetle will now happily do. As for range, Richard says it will cover 100-miles with ease. The battery monitor shows percentage loss at approximately the same rate as the miles glide by.

    Steering is heavy until you get it rolling, no power steering here and the thin-rim wheel is a delight to hold. Manoeuvring the car reminds me of old black & white movies when actors inexplicably exaggerated steering. The experience is definitely classic and not far removed from driving the original car, only without the thumping soundtrack, a lot more speed and – I’m told – better handling. The Beetle accelerates like a modern electric car, although it has a unique whine all of its own, akin to a small turbine. On the return approach, there’s a steep climb to navigate. Richard suggests quickly whipping it into first and I hesitate for a moment. We’re now stopped facing up the hill. I fall into modern driving mode and attempt a classic hill start, only I’ve given it a few too many Amps and have managed to spin the rear wheels. We’re doing a burnout in a 1965 electric Beetle. It’s an accidental thrill I’m hugely apologetic about. However, this nicely demonstrates the torque available from the AC electric motor and would have been an impossibility in the original petrol car. It’s fun and we both return with larger grins than a Cheshire cat.

    The big question for many is, did I miss the flat-four engine sound? No, while I can appreciate a classic that’s been restored for originality, a part of me has always wondered why people put all that effort in and not take the opportunity to improve a car if they can. There are countless examples in the classic car world, like Triumph Stags that were built with a design flaw that meant many overheated, ruining the engine. Long after the cars were built, a modification now exists to correct this. Would a purist complain that a modified Stag no longer overheats? I doubt it. Applying the same logic, what Electric Classic Cars has done is take an old obsolete car and make it usable in today’s modern driving conditions. That, surely, is the whole point and the best form of recycling.

    And the cost for this? Well, that’s a bit like asking a builder to construct a house without first saying how many rooms it has and what size it will be. However, Richard advises a conversion costs around £25,000. That’s fair considering the effort required, technical know-how and actual cost of components used, which amount to well over £10,000.

    The Volkswagen Beetle isn’t the only car Electric Classic Cars convert, although it is the vehicle they have most expertise on. In the workshop while I was there was a Porsche 911 (964) and Range Rover Series 1, as well as another Beetle. Richard told me of more customer cars he’s about to start on too, including a special Jaguar E-Type that will out accelerate a Tesla Model S and have a 200-mile range too. Would I be tempted to have a classic converted to electric power? After my experience in the VW Beetle the answer is a very definite yes.

    Wales, wet, mountains, autumn, red, Volkswagen, classic, wind, whirr, electric, smiles.
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Adam Towler reacted to this post about 4 years ago
    CAR / #VW-Beetle / #Volkswagen-Beetle / #Volkswagen / #VW / #Volkswagen-Beetle-MkI
    Run by Martin Port
    Owned since March 2011
    Total mileage 89,144
    Miles since May
    report 1446
    Latest costs £8.50

    The Port family with the ‘back-up’ classic and its new friend at Bicester Scramble. Inset: snapped window regulator arm.

    A FAMILY OUTING ON DRIVE IT DAY

    Yet again, without realising it, the Beetle adopted the role of ‘back-up’ classic when the Landie suffered its catastrophic hub-bearing failure.

    With a visit to Bicester Heritage long planned for the April Sunday Scramble, there was always going to be only one vehicle for the job. But, with the IIA suddenly stranded on the driveway, we squeezed into the hastily polished VW for the trip up the A34 to the former RAF base.

    Although the Beetle was sold as family transport, there are limitations once you’ve fitted a child seat in the rear and wedged a lanky teenager into the front. Certainly Mrs P, whose selfless attitude dictated that she sat in the back, suffered from a lack of legroom once I’d made myself comfortable! That said, the relatively short hop north to Bicester was uneventful and we pulled onto the field next to a slightly later Beetle before proceeding to extricate the family from the Volkswagen.

    A good day was had by all and, with a chilly wind blowing, it was quite pleasant to make our way home with a little warmth passing over our feet thanks to the stuck flap on one of the heat exchangers. As nice as that was, though, it served as a reminder that I needed to sort it out. With temperatures on the rise, said heat was becoming a bit much – particularly when Mrs P transports guinea pigs in the footwell (that’s not a euphemism and is a story for another time).

    Giving the lever and spring beneath the vehicle a good dousing with WD40 got things moving once again, although I noted just how corroded the exchangers are becoming so they will need to be replaced before winter for sure.

    The seat runners had also been on the ‘to do’ list for a while. Moving the driver’s chair was becoming increasingly difficult and it was also rocking on the fittings.

    Investigation revealed that one of the packing strips that sit between the runner and seat base had split and come adrift. Clearly the other one was heading the same way, too.

    A fresh set arrived in the post and I took advantage of a spare lunch hour to remove the seat, fit the new strips and then give them a coat of lubricant. I also refitted the main tensioning spring, which had come adrift and had been jamming the sliding mechanism.

    The seat now moves nicely, but there was another one of those little jobs nearby. Tightening the loose window winder became irrelevant because the arm snapped, leaving the glass in the down position at the most inconvenient moment: just prior to the school run and Mrs P’s commute to work. She managed to wrestle it closed with determination, and I had a rummage in my spares drawer to dig out a replacement that I’d put somewhere.

    Undoubtedly more important than making sure that the Beetle works though, is having a fully functioning stereo. After the windscreen washer had doused the RetroSound item, the tuner had become even more temperamental than usual. With several spare FM head units in the garage, I pulled out a Clarion system that had previously been in my Scimitar GTE.

    Adapting the wiring from the old to the new stereo was straightforward, although I didn’t want to have a modern set-up in the dash so I hid it in the glovebox. This was complicated slightly by the shallow dimensions and because the bonnet release is also in there, but I didn’t mind cutting the scrappy liner so that the head unit could protrude into the underbonnet area.

    A replacement glassfibre liner made to house a radio is available but apparently the fit is poor. While I give that aspect some further thought, I have made a temporary fascia from plywood and mounted it within the liner at an angle so as not to obstruct the bonnet release.


    I was then finally able to refit the original factory blanking plate that I had safely tucked away when we fitted the RetroSound unit. The dash now has a cleaner appearance and the reception is better with the Clarion, plus the sound is clearer and its built-in USB slot means that we can keep iPhones charged while on the move. This will eventually be upgraded to a DAB unit as installed in the Land-Rover, but it’s a more than adequate solution for now.

    Front seat simply slides forward and out. Fresh packing strips are slightly shorter. Plywood fascia for ‘new’ hi-fi in glovebox. Rear of liner had to be cut to allow fitting. Blanking plate restores the original look.
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Martin reacted to this post about 4 years ago
    DEAD PAN / #VW-Beetle / #Volkswagen-Beetle / #Volkswagen / #VW /

    It’s not very often that the pages of DRIVE-MY are graced with a car that isn’t water-cooled, but on some occasions we can definitely break the rules. Words and photos: Tony Matthews.

    Just look at this menace. Its owner is a man that comes from sunny Spain, from a small town just on the outskirts of Barcelona. He is responsible for creating one of the most notorious air-cooled car clubs in the whole of Europe, ‘The Panscrapers’. The club was established way back in 2005, born out of Carlo’s passion for the VW Beetle. It gives him a place where he can get away from everything with the guys and just live out his dreams inside a garage.

    These guys truly live the ‘low lifestyle’ by scraping pan without the help of air bags! Yes that’s right, this car is this low and it’s static… crazy huh?

    Well, the Panscrapers are different to most groups of people and love to create some of the most outrageous projects you will ever see. There are no show ’n’ shine queens here, just lots of grease with spanners in hand, late night project builds, friendly banter and the must-have barbecues made out of oil drums. I first came across these guys through Facebook over four years ago and I made it my mission to one day make the trip to Barcelona to hang out with them. I mean, who wouldn’t want to chill with some down-to-earth passionate car guys at their garage and watch them build some epic dubs?

    So after several years of liking their project photos on their Instagram feed, the time came to take that trip and this black Oval was the icing on the cake. I’d seen their previous builds, but when I saw a front three-quarter photo of ‘Darth Vader’ as Carlos calls her, it just blew me away! That stance, that deep black paint, those 15-inch BRM wheels and then those headlights… It’s the complete package and what a classic custom Beetle should be all about in this writer’s book. As we arrived at the Panscrapers garage, we were greeted by all the crew who are an awesome bunch of guys, mainly because they are just so chilled out. As they opened the garage doors we were presented with a mix of Beetles, Karmamn Ghias and Campers and Vans, some completed and some to be future builds. Then out of the corner in the dark, was sitting Carlos’ Darth Vader.

    This is Carlos’ dream car which he purchased over 16 years ago and it took him one year to build with the help of his Panscrapers crew. Having been a fan of the classic Beetle since he was a young boy, he made it his mission to own his very own Beetle. But, it’s not Carlos’ first project – he has had a 1952 Split, a ’57 Oval, a Type 3 Squareback, a ’61 Singlecab and many more besides.

    So, why Darth Vader? “He’s damn cool, no? I love the Star Wars movies and I remember watching it one time and thinking how cool it would be to add a touch of Darth Vader to the Beetle I was building,” said Carlos. We think it’s a really cool idea and we particularly love that he didn’t go for some over-the-top, filler-type body kit to bring across that Darth flavour. He just kept it simple, going all black and then adding that finishing touch – those headlights!



    “I wanted to make the front end look mean and I was scratching my head on how I could do this,” recalls Carlos. As he didn’t want to alter the original lines of the Beetle, he looked at the headlights. His inspiration came from the KDF headlight covers that military vehicles used back in World War Two which were fitted so that during night time black outs, the driver could still have some light to see the road. I have to say, when I first saw those headlights, I had no idea where they came from, so for me, it was a brief history lesson that day. Who would have thought that a part used to help save soldiers’ lives would end up being one of the coolest modifications I’ve seen on a classic Beetle?

    Whilst Carlos and the rest of the Panscrapers crew got busy stripping the Beetle for its makeover, the engine was sent to the guys over at Kombiman Garage for a complete rebuild, with some added parts for that extra grunt. I mean, if you’re going to slam the heck out of a car and scrape pan, the engine has to also sound super mean.

    First things first, the main modifications were to the floor pan to get it as smooth as possible and then Carlos had the original front beam narrowed by four inches. He then added dropped spindles and some Peugeot 106 Rallye shocks at the rear. As you can see, the drop is just perfect and gives the Beetle one tough stance. Wheel choice-wise, Carlos used to have a set of Porsche 944 wheels, but then decided on these 15-inch BRM Flat4s, which were then custom-painted to match the bodywork.

    Whilst the engine was still at Kombiman Garage, they had the entire bodywork and then got busy with the interior, retrimming the seats in black and cream leather with matching doorcards and adding Simpson seat belts. Not much more was done inside, apart from adding a Empi GTV Flat4 steering wheel, a large Autometer gauge and a Gene Berg gear shifter – Beetle classics if ever there were any.

    A few days after the interior was ready to be put back in, and the engine was also delivered with all the parts needed so Carlos and the boys could put it back in. After a week’s worth of hard graft in the evenings, Darth Vader was ready. And like any project car when it’s finished, you have to go for a test drive.

    Carlos remembers that day so clearly. “It drove like a dream! It handled perfectly, the engine was incredible, it was super low and then when I added the headlight covers, it was just jaw-dropping,” recalls Carlos. DRIVE-MY doesn’t do air-cooled that often, but when we do…

    Look at this lot, they’re so happy, loving the air-cooled life and all that. Excellent sandal game going on with the guy on the bottom left too…


    Dub Details

    ENGINE: Specially built 1776cc by #Kombiman-Garage with 1776 Mahle forged pistons, Engle 100 camshaft, lightened flywheel with 0.9kg removed, 40 #Dellorto carburettors, #Pierburg electric fuel pump, #Bosch-009 , Type 3 gearbox, #Kennedy clutch

    CHASSIS: 4.5x15” and 5.5x16” #BRM-Flat4 wheels, custom painted with 135/70/15 and 145/80/15 tyres. Floor pan is entirely smoothed, beam narrowed -16cm no shocks, dropped spindles (front), three splines rear, Peugeot 106 Rallye rear shocks, restored Porsche 356B drum brakes

    EXTERIOR: #KDF headlight covers, paint is black L041

    INTERIOR: Custom leather retrim, Simpson seat belts, Empi GTV Flat4 steering wheel, Autometer gauges and Gene Berg gearstick
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Adam Towler reacted to this post about 4 years ago
    GOODBYE TO THE RUSTY WINGS

    Car #VW-Beetle 1300
    Run by Martin Port
    Owned since March 2011
    Total mileage 83,510
    Miles since January
    report 1760
    Latest costs £230

    It’s now over a year since I took delivery of the replacement front wings for the Beetle. They stayed in the box all through last winter because there seemed little point in fitting them while there was salt on the roads, but eventually I dropped them off to Berkshire Bodyshop in Newbury to have them painted.

    They also took the fuel flap to use for colour-matching the paint and all was going to plan until the #VW got rear-ended (DRIVE-MY in January site update), but once that hiccup was sorted it was time to press on with the wing replacement.

    When I finally got around to collecting the painted items, they looked great and the freshly applied Iberian Red was a decent match, even when seen alongside the car’s ageing original panels.

    So, with the car occupying the #Drive-My workshop once more, I set about dismantling the front end in preparation for the refit. Now I shan’t lie – there are occasional perks to working for a car magazine and having titles such as Autocar and What Car? as stable mates. In this instance, that meant Volkswagen UK handing me the keys to one of the latest Beetles while ours underwent surgery.

    Of course, it would be unfair of me to directly compare the little #Volkswagen 1300 #Beetle flat-four original to the turbocharged six-speed Sport model of #2015 , but needless to say both are a lot of fun… albeit in different ways and at very different speeds. I was perhaps ever so slightly disappointed by the lack of that typical Beetle hallmark in the new model, though – the faint whiff of exhaust fumes coming through the heater! What I can testify, however, is that Volkswagen build quality appears to be as good as ever – something that I was very glad of as the bolts securing the wings to the body undid without fuss or the need for a grinder. And yes, before Volkswagen starts looking closely at its loan car, I’m back to talking about the old one again.

    In fact, I was not only pleased to note that the corrosion on the original wings was restricted to just around the headlights, but the panels to which they bolted showed almost no sign of anything untoward – not bad for a 44-year-old car that gets used in all weather.

    I had been a little nervous about the quality of the new wings, because the budget hadn’t quite run to original-equipment parts. Pleas-ingly, however, the fit of the VW Heritage-supplied panels was excellent, and I managed to get both wings loosely positioned in about 20 minutes. Only the bolthole attaching the rear of one wing to the running board needing a bit of minor fettling with the Dremel. Prior to fitting the wings, I’d made a shortlist of parts that I felt needed replacing instead of refitting.

    The headlights had always been pitiful so I’d ordered some 60/55w halogen bulbs as an upgrade to the standard 50/45w tungsten ones, as well as a new bumper, plus rubbers for where the mounts pass through the wings. With a little adjustment, the freshly polished headlamp assemblies and wing-top indicators were refitted once I’d fixed a snapped stud by drilling it out and replacing it with a discreet nut and bolt.

    I then fixed the new bumper to the mounts and slotted them through the rubber inserts before bolting in place, leaving just one more job to do: thoroughly coating the inside of the new wings with Dinitrol in a bid to keep any future corrosion at bay.

    Of course, while the wings now look fantastic, the rest of the body is getting a little tired and so it would be great to have the remaining panels resprayed at some point. In the meantime, though, the next job will be to address the growing hole in the bottom of the driver’s door. The easiest solution will probably be to replace it with a solid secondhand unit that can be repainted.
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Adam Towler reacted to this post about 4 years ago
    This splendid May #1955 (ribbed door) Oval #VW-Beetle / #Volkswagen has been in my family since 1957. It was first owned by my dad’s brother then sold to my dad, Cliff, in 1959. ‘Pappa’s Car’, as my 5 year old son Nathan calls the Oval (and all other Beetles for that matter), was a car destined to never leave the Sedgman fold. My dad had owned many a Volkswagen, mainly Type 3 Wagons for transporting the family around, and he also owned one of the first Split Window Beetles ever to come into Australia and started the #VW Split Window Club of Australia in the early 80s. There were 13 owners back then.

    My dad’s love of Beetles was well known amongst the VW fraternity, both nationally and internationally, and our doorstep was forever awash with boxes of parts ordered in from overseas. This was in the days of pre-internet and fast air delivery, so my dad built up quite a rapport with the local postal and courier people. Patience was a virtue in the 80s, and sea freight did require a lack of urgency when restoring and repairing classic VWs, but people never seemed time poor or in quite so much a hurry as they are these days.


    This even applied to photography. Dad and I would always go to the annual DOVW in Melbourne, and I vividly remember taking photos of my favourite cars on my Kodak Instamatic camera and then waiting to take them to the pharmacy for developing. No instant image gratification back then.

    Family trips and holidays were very much VW orientated, with my dad always hiding an ulterior motive for wanting to visit a certain place. My mum quickly woke up to this ploy, but it never bothered her too much. My dad was also the ‘go-to’ person for those in the VW circle who needed parts over the years, and although he still attends regular swap meets, his stocks are beginning to run thin. Along with his parts and car, my dad has a keen interest in Beetle models and early literature, something he is still very passionate about. But it is the ‘55 that still gets all the attention.

    As an iconic Melbourne Beetle in the 80s, my dad spent many hours doting over the small window bug and modernising it to keep up with the times.

    This included 1970s taillights and front fender indicators, a 1500 decklid with chrome vent covers and rear valance, 1500 front bonnet and badge, 1500 headlights and front and rear bars, 1500 seats, a 1835cc engine with 1500 transmission. There were also a plethora of accessories such as a flying #VW-Beetle / #Volkswagen-Beetle emblem, rear stone guard protectors, driver’s side wind deflector, mesh headlight protectors, clear green sun visor, custom hubcaps he adapted from a Humber (pop riveted to 4.5” rims), whitewalls and even a set of Lucas Flamethrower spot lights as used on British cars.

    The car over the years has appeared in many publications, including Issue of #Drive-My , the British Beetling magazine and Melbourne’s The Age and The Sun newspapers to name a few.

    This was how my dad used the car as his daily driver, and considering the Beetle covered a 50km round trip every day, it remained a reliable and remarkably sound Beetle. Of course my dad cared for the car in a way a car enthusiast only can. He would always wash and dry the car each time it was out in the rain, and during the day he even convinced the management at Melbourne airport (where he worked) to have it parked in the lock-up area normally reserved for pilots. So when it came time for dad to pass the car onto me, I was given a big responsibility of continuing the ‘55 legacy.

    The Oval was in a good used condition when I took the wheel, and I was torn between a full period restoration or keeping the iconic 80s look of the car that had become so well known. In the end, and with my dad’s blessing, I decided to essentially return the Oval to factory specifications along a vintage speed theme with period accessories. Given how heavily modified the car had become, this would be a slow and delicate operation, and my task began with sourcing all the 1954/55 period parts and panels to replace dad’s modernisation design.

    Dad got the ball rolling with some NOS heart shaped taillights and a few other odds and ends, and then it was a case of asking and chasing parts. Rick from Volksrecycle chipped in a few period components, as did Nathan Leversha and Boris Orazem from Vintage VeeDub Supplies in Sydney who had many quality reproduction parts in stock, such as rubbers.

    I purchased a 1200 twin carb Okrasa motor kit from Wolfsburg West in the States, and had Boris Senek from Volkscare in Melbourne to rebuild an early 36hp engine I had also sourced.

    I did keep some of the accessories dad already had on the car, which included the aluminium strips on the vent under the Oval window, the ammeter, Motometer clock and Denhe fuel gauge on the dash and the collapsible gear stick, but of course the 80s mods were all removed. My next challenge was finding somewhere to work on the Oval, and a big shout goes out to my mate Damien Prunty for the loan of his garage during the 4 year restoration. Damien’s garage was where I stripped the ‘55 back to its bare bones and began the transformation.

    The build agenda began with Jason Carroll at Chequered Flag Restorations welding up the front and rear fender indicator holes and replacing all the non-period panels. The only rust of any mention was the battery tray, which I replaced with a new period pan section.

    Dad had painted the shell in a two tone black over grey scheme - neat, but not factory. After the old paint had been removed, I chose the factory black for that period for both body and pan. Now the time had come to bring it all back together. I decided to keep the 1500 transmission rather than source an original syncro box , and added a Wolfsburg West Abarth 36hp exhaust onto the Okrasa inspired motor.

    The drum brakes were also kept, albeit large Type III drums on the rear. I chose to fit an adjustable beam so that I could play with the ride height to achieve a more vintage speed stance. Other than that, the rest of the running gear was refurbished as stock and parts replaced where necessary. The choice of wheels for the car have seen me change styling cues a few times, with Radars, Repro Empi Sprintstars, Porsche Fuchs and even the real deal steel Empi Sprintstars finding their way under the Oval.

    The latest set of boots, and the ones I am the most comfortable with, are the tried and true Mangels, 4.5 front and 5.5 rear colour coded to the car and fitted with Sierra Madre imitation 356 brushed chrome drum covers for that vintage speed look. The wheels are wrapped in Nankang 135/R15 and 165/R tyres front and rear respectively.

    The interior was given the genuine ‘55 makeover, starting with a restoration of an original batwing steering wheel. Original seats were sourced and restored and painted in their correct factory colour, and then Steve Randall reupholstered them in original stitching style whilst replacing the headlining supplied by Wolfsburg West. The original carpet was threadbare after many years of solid use, so Steve laid in fresh German Square Weave. Period lap sash vintage speed belts in contrasting red and slip-on accessory headrests upholstered to match the interior trim helped finish the look I was aiming for.

    I also threw in a few subtle touches that make this ‘55 quite special. Securit rear pop-out windows are a favourite of mine and really add a touch of class, and the bumpers, over-riders, front quarter vent window frames and all handles were rechromed. A combination of NOS and former chrome body moulds make the exterior complete, and I finished with a pair of Amercian style 1955 front turn indicators (basically early Kombi).

    The 80s deletes have not made ‘Pappas Car’ any less the cherished ‘55 that either myself or my dad hold fond memories of. I was always conscious about creating a look that was true to the vintage of the Beetle, rather than follow another trend or fad. Therefore, there is no narrowed beam, clear coat patina or rope and canvas wrapped around the front bars. The restoration was not without its moments, though, and had to be worked around moving house twice with renovations and is still being stored, but I am now in the final stages of completing my own garage so ‘Pappas Car’ can finally come home. I would also not start with a pre-built motor, only having to pull it down and start again, but rather build one from scratch to suit the build goals.

    And although the collective price of parts used and labour invested into the resto are probably more than the value of the car itself, the ‘55 was well worth every penny and hour spent, and its place in the Sedgman garage is priceless. My son Nathan at 5 years old has started asking me when it will be his - he will have to wait patiently like I did! ‏ — at Melbourne Airport (MEL), Departure Dr, Melbourne Airport VIC 3045, Australia feeling blessed
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Adam Towler reacted to this post about 4 years ago
    BIG BAD WOLFF / #VW-Beetle / #Volkswagen-Beetle / #Volkswagen / #1961 / #VW /


    After over a decade involved with the watercooled VW scene, Andreas Wolff switched his allegiance to worship at the church of air. This ’1961 VW-Beetle is the end result…

    Words: Simon Jackson. Photos: Patrick Hille.

    “For me it’s the only real Volkswagen – I love the Beetle. It’s a special car, not only because of the design, but because young and old people love them – the passion is huge.”

    Berlin-based Andreas Wolff has been into cars, and primarily Volkswagens, since he was a kid. His teenage dream was admittedly pretty humble; he hankered after a Mk2 Polo hatch believe it or not, a dream he fully realised aged just 20 with a hopped-up 1988 86C project running a tidy 240bhp 1.5-litre turbo lump, and shod with deliciously timeless BBS E30 split-rims. That car stayed in Andreas’ possession for ten long years, it transformed numerous times during that period too, leading him on to a bunch of other VW projects afterwards. Two Mk2 Golfs, a rare two-door Mk2 Jetta, and a string of modified VAG daily drivers followed, but after over a decade dabbling in Wolfsburg’s various water-cooled offerings, Andreas made the switch across to the older air-cooled VW motors. In summer 2009 a classic Beetle project finally beckoned.

    “I searched for three long months until I found the car I wanted near Hannover,” Andreas explained, “I wanted a pre-’64 Beetle with a rag-top in good condition and in a rare colour.”

    Andreas came across the green ’61 1200 you see here and instantly knew it was the right car for him. Complete restoration work had been undertaken some 12 years previously, so the vehicle was in decent nick, yet rocking some signs of patina and interior distress. Various parts were either missing or weren’t period correct on the car (which bugged Andreas), but the 31-year-old reasoned that he’d be able to put all that to rights easily enough. This, despite the fact he knew nothing about either sourcing Beetle parts, or working on, and navigating his way around, the cars themselves. Who worries about little details like that, eh?

    Andreas bought and drove the ’61 as it stood (bar the additions of an #EMPI shifter and #K&N filter) a few times a week over a two-month time frame, until winter arrived. With the howl of wind, rain and snow, the car was taken off the road for the planned transformation to commence.

    “I love the colour, it’s one of the rarest; it’s called Beryl green and they only painted Beetles in it between 1961-’63,” he said. “I also love red, so I decided to mix both colours. My inspiration is my wife Astrid.”

    Andreas and Astrid make no excuses for having a crush on the ’50s and ’60s, so Andreas decided to style the car, nicknamed ‘Betty’, in a ’50s Americana vein. While we’re not usually fans of people naming their cars, with the story behind Andreas’ car, we’ll make an exception… “On the aluminium part of the rag-top the name Bettina Giljohann has been scratched in,” he recalled. “It might be the name of a previous owner, so the car is called ‘Betty’. That’s also why Betty Boop is on the mirror inside; a symbol for classic America.”

    So, October 2009 saw Andreas kick-start his planned programme of mods. First the car was fastidiously checked for rust and rot. Fresh rubbers, lights, and other parts went on to the car, and Andreas ripped out its interior, which it turned out wasn’t original, having come out of a later 1968 car. It took eight weeks to track down a period perfect set of 1961 inners, but Andreas used this time wisely to prepare his air-ride setup. Now, many folk we come across have their air-assisted gubbins fitted by an external expert, but Andreas built his up at home (tank, valves, compressor and tubes) learning as he went.

    “The first problem was the spring plates; they were rusted to the torsion bars, so I needed new plates and bars!” Andreas recalled. “Then I worked on the narrowed front beam with lowered steering knuckles, and the air-ride shocks.” Andreas also added his reworked wheels at this point, narrowed at the front from 4” to 3.5x15”, and banded those out back to 5.5”, up from the original 4”.

    Andreas then fitted new carpets and gauges, and refinished the whole cabin in white and red vinyl in a ’50s diner-style, he painstakingly undertook all this work himself. “I put in the new carpet and some details like the VDOs, MPH speedometer, a secret modern stereo and I painted the interior pearl white and put the red/white vinyl leather in by myself. It was a lot of work!” Andreas said.

    With the interior looking far sprightlier, Andreas moved his attentions on to the engine compartment out back. Some brave soul had painted the ’bay orange (we just hope it wasn’t Betty…), so this needed addressing quick smart. Black paint was shot across the bulkheads, accented with Andreas’ white/red theme, and the block was polished up to a presentable level too. And that’s how the Beetle stood for its first show season in 2010.

    “When the next winter came I decided to change something more on the technical side,” Andreas said, “so I fitted a new longer range gearbox and swing axle, which is very difficult to change – it was the first time I’d ever done this!”

    While Andreas had the car apart he also changed that first air-ride install. His original system had employed axle valves, which Andreas switched to single wheel valves: “The air-ride is home-made,” he explained. “I spent weeks on it. I wanted to lower the car as much as possible with the perfect stance. I can now drive it with 0bar of pressure on its shocks.”

    In fact there were a few teething problems with the air-ride system. Andreas found himself chasing a leak around the car for some time, only to discover a dodgy weld on the tank was to blame. With this located and the tank changed in good faith by the supplier, everything has run beautifully since. Andreas also sourced and fitted a rare set of Porsche 356 carburetors. A Piper exhaust and electric ignition setup was slotted on for good measure, excess cables were relocated or removed, and the heater arrangement was deleted for aesthetical purposes.

    The ’bay now looked pretty smart. A couple of cool additional details, like badges and that driving school secondary mirror were added for a splash of personality. Ultimately though, Andreas has tackled the whole lot himself bar any welding, and all in an underground car park where he couldn’t even fully open the car’s doors! After this second stage of the makeover the car now completely reflects Andreas’ original brief; hinting at ’50s and ’60s American themes and colourways, and looking every inch the cool classic.

    “I was a bit doubtful of how people would react to the car at its first outing because of the colour mix, but in Austria for Wörthersee 2010 everyone was positive,” Andreas said. Since the trip to the ’See, the car has been well received all across Europe at events from MIVW in Holland to the Wolfsgruppe VAG Event in Poland, and seeing it in print here we’re sure it won’t surprise you to hear that. Having crossed over from the water- to air-cooled VW scenes, Andreas is better placed than most to pass comment on how the two sides of the Volkswagen coin compare. “Both scenes are very cool, both are special,” he said.

    “But I hate it when guys discriminate against each other because of their preference, we all have the same passion; cars! But the retro car scene is growing up, many of my friends have started projects with old cars (not only VWs). It’s a new love and I think some guys were inspired by Betty!”

    We often joke that project cars are never finished, but could Andreas’ be the exception to that rule? “It’s the first car for me where I can say yes! It is finished, I think Betty is perfect,” he laughed. “There are no new projects planned, but the dream is an American V8, a muscle car or ’rod from the ’30s to the ’60s. We’ll see…”

    Yes, we will see. In fact, we would actually love to see Andreas’ customised take on a thoroughbred period American motor – something tells us it would be pretty damn special.

    “It’s the first car for me where I can say yes! It is finished, I think Betty is perfect”

    Dub Details

    ENGINE: 1600cc air-cooled engine with Porsche 356 #Zenith-NDIX-32 carburetors, #Piper exhaust, 123ignition 12V electrics, heating system deleted, cables and brackets deleted and smooted, ’bay repainted gloss black with red/white details, long Rancho gearbox.

    CHASSIS: Front beam shortened 3.25”, lowered steering knuckles, notched rear spring plates, lowered rear torsion bars, highjackers front/back for the air-ride function, 19L chrome tank with four valves and #VIAIR / #Viair-480 / Viair compressor, front wheels narrowed from 4” to 3.5x15” with 135/70 tyres, banded rear wheels from 4” to 5.5x15” with 185/65 tyres, Ravus system whitewalls with stainless steel hubcaps and beauty rings.

    OUTSIDE: Export bumpers, colour-coded roof, US-spec sealed beam front lights with yellow tints, US-spec red rear clusters, hooded Albert swan-neck mirrors, pop-out rear windows, red window breezies, red/white Berlin badge on the front hood, lots and lots of chrome.


    INSIDE: Red/white interior, EMPI shifter, flower vase with red/white flowers, hidden air-ride control, rabambus storage, MPH-speedometer, RPM and oil temp #VDO in original speedometer optic (needle strips), Venetian shades at rear, driving school double mirror, original #Blaupunkt-Frankfurt radio with one speaker, #Hirschmann antenna, hidden modern stereo with #Pioneer head unit, two-way rear-system and subwoofer.

    SHOUT: Special thanks to my wife (Astrid), Denis, Moosi, Janek, Low-Familia, Watercooled-Customs and Patrick Hille/VWHome.de.
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
No hashtag items to show here
Unable to load tooltip content.

Drive-My.COM MEDIA EN/UK based is United Kingdom’s top cars/retro/classic/modern/tuning/moto/commercial news, test drive, classic cars and classifieds. For car advertisement be it an RETRO/CLASSIC/OLD-TIMER/NEW-TIMER, Coupe, MPV, SUV, Luxury Car, Commercial vehicle, OPC car or even an auction car. We update you with latest information on new car prices from both parallel importers and car authorised dealers with brands such as Aston-Martin, Bristol, TVR, Bentley, Ford, Porsche, Jaguar, Land Rover, Citroen, Tesla, DS, Alfa Romeo, Subaru, Toyota, Acura, Honda, Nissan, Audi, Kia, Hyundai, Volkswagen, Volvo, Mitsubishi, BMW, Mercedes-Benz. Find new car pricelists, new car promotions, new car reviews, latest car news, car reviews & car insurance UK. We are also your information hub for parking, road tax, car insurance and car loan, car audio, car performance parts, car discussion, motor insurance, car grooming, car rental, vehicle insurance, car insurance quotation, car accessories, car workshop, & car sticker, tuning, stance and Cars Clubs

Our Drive-My EN/USA site use cookies